Toshihiro Shiratori
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Toshihiro Shiratori has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
- Hidetoshi Takahashi
Keio University
11 shared publications - Ohga Nomura
School of Integrated Design Engineering, Graduate School of Science and Technology, Keio University, Yokohama, Japan
3 shared publications Ryusei Ando
School of Integrated Design Engineering, Graduate School of Science and Technology, Keio University, Yokohama, Japan
3 shared publications- Takuto Kishimoto
School of Integrated Design Engineering, Graduate School of Science and Technology, Keio University, Yokohama, Japan
3 shared publications - Yukitake Nakahara
School of Integrated Design Engineering, Graduate School of Science and Technology, Keio University, Yokohama, Kanagawa, Japan
3 shared publications Kyota Shimada
School of Integrated Design Engineering, Graduate School of Science and Technology, Keio University, Yokohama, Japan
2 shared publications
Latest Publications
- 1 November 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (21) , 32163-32170
Six-Axis Force Plate Utilizing Sampling Moiré Method and Mirror-Based Optical System With a Single Camera
- 1 November 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (21) , 32163-32170
Six-Axis Force Plate Utilizing Sampling Moiré Method and Mirror-Based Optical System With a Single Camera
- 11 June 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Letters
- Vol. 10 (7) , 2503404
An Evs-Based Stand-Alone Water Flow Sensor With Accumulation-Time Feedback Control
Measuring water flow velocity is essential in a wide range of fields, including the operation of underwater drones and studies of marine animals. Conventionally, screw- and Pitot-tube-type sensors have been used as compact sensors; however, these approaches suffer from reduced sensitivity at low flow rates, resulting in degraded measurement accuracy. Here, we propose a water flow sensor that enables measurements under low-flow conditions utilizing an event-based vision sensor (EVS). The flow speed is estimated from the trajectory lengths of naturally occurring tracer particles, such as bubbles and debris, in accumulated event images, using a particle tracking velocimetry (PTV) approach. By adaptively controlling the accumulation time based on the flow speed, the trajectory length is maintained. Water-tunnel experiments conducted over 0.16-0.57 m/s using seeded tracer particles showed a linear response with a linear fit of V = 1.61 Vref + 0.30 and R2 = 0.98. These results demonstrate the feasibility of EVS-based trajectory sensing with accumulation-time feedback control in the tested low-speed range
- 11 June 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Letters
- Vol. 10 (7) , 2503404
An Evs-Based Stand-Alone Water Flow Sensor With Accumulation-Time Feedback Control
Measuring water flow velocity is essential in a wide range of fields, including the operation of underwater drones and studies of marine animals. Conventionally, screw- and Pitot-tube-type sensors have been used as compact sensors; however, these approaches suffer from reduced sensitivity at low flow rates, resulting in degraded measurement accuracy. Here, we propose a water flow sensor that enables measurements under low-flow conditions utilizing an event-based vision sensor (EVS). The flow speed is estimated from the trajectory lengths of naturally occurring tracer particles, such as bubbles and debris, in accumulated event images, using a particle tracking velocimetry (PTV) approach. By adaptively controlling the accumulation time based on the flow speed, the trajectory length is maintained. Water-tunnel experiments conducted over 0.16-0.57 m/s using seeded tracer particles showed a linear response with a linear fit of V = 1.61 Vref + 0.30 and R2 = 0.98. These results demonstrate the feasibility of EVS-based trajectory sensing with accumulation-time feedback control in the tested low-speed range
- 2 June 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Letters
- Vol. 10 (7) , 2503504
Biaxial Optical Cantilever Combining On-Chip Patterned Laser and Sampling Moiré Method
The optical lever method is a widely used high-resolution displacement sensing technique in various micro- and nanoscale sensing systems. In this method, cantilever displacement is evaluated by detecting changes in the position of reflected light using a photodiode; however, precise optical alignment is required during setup. To address this issue, optical lever systems combining a cantilever with the sampling moiré (SM) method have been proposed. More recently, approaches using on-chip pattern lasers that directly project periodic patterns have attracted attention, as they simplify both system configuration and cantilever fabrication. In many applications, not only normal displacement but also torsional deformation must be measured to evaluate multi-axis forces and moments. Although the SM method is well suited for analyzing two-dimensional periodic patterns, generating well-defined two-dimensional lattice patterns using mechanical gratings is technically challenging. In this study, we propose a biaxial optical cantilever sensor that integrates the SM method with an on-chip pattern laser capable of directly projecting a two-dimensional checkerboard pattern. The projected pattern was captured using a lens-less camera and analyzed using the SM method. Experimental results confirmed that the checkerboard pattern shifted independently in two directions depending on the force application point. The achieved resolutions were 32.4 nN for the normal force Fz and 201 μN·μm for the bending moment Mx, demonstrating the feasibility of simple and high-resolution two-axis force measurement.
- 2 June 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Letters
- Vol. 10 (7) , 2503504
Biaxial Optical Cantilever Combining On-Chip Patterned Laser and Sampling Moiré Method
The optical lever method is a widely used high-resolution displacement sensing technique in various micro- and nanoscale sensing systems. In this method, cantilever displacement is evaluated by detecting changes in the position of reflected light using a photodiode; however, precise optical alignment is required during setup. To address this issue, optical lever systems combining a cantilever with the sampling moiré (SM) method have been proposed. More recently, approaches using on-chip pattern lasers that directly project periodic patterns have attracted attention, as they simplify both system configuration and cantilever fabrication. In many applications, not only normal displacement but also torsional deformation must be measured to evaluate multi-axis forces and moments. Although the SM method is well suited for analyzing two-dimensional periodic patterns, generating well-defined two-dimensional lattice patterns using mechanical gratings is technically challenging. In this study, we propose a biaxial optical cantilever sensor that integrates the SM method with an on-chip pattern laser capable of directly projecting a two-dimensional checkerboard pattern. The projected pattern was captured using a lens-less camera and analyzed using the SM method. Experimental results confirmed that the checkerboard pattern shifted independently in two directions depending on the force application point. The achieved resolutions were 32.4 nN for the normal force Fz and 201 μN·μm for the bending moment Mx, demonstrating the feasibility of simple and high-resolution two-axis force measurement.
- 6 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (10) , 15095-15102
Two-Axis Transparent Force Plate for Droplet Collision Measurement Using High-Speed Line-Scan Camera and Sampling Moiré Method
Force measurement and interface observation during droplet impact are essential for understanding droplet behavior in both scientific and industrial applications. However, achieving both backside optical transparency for interface observation and two-axis force measurement for quantifying shear-force effects has been challenging with conventional force-sensing methods using a single device. In this study, we propose a transparent two-axis force plate based on the sampling moiré (SM) method combined with a line-scan camera, which enables high-temporal-resolution force measurement while permitting optical observation beneath the impacted surface. The proposed device consists of a spring-supported, laser-cut glass plate with a periodic striped pattern and a prism-based optical system. A line-scan camera is employed to overcome the inherent trade-off between spatial resolution and frame rate associated with area-scan cameras. By duplicating the pattern image using a prism and analyzing the resulting displacements via the SM method, in-plane and out-of-plane forces are independently measured from one-dimensional images. Calibration experiments confirm linear force–displacement characteristics, with force resolutions of Fx = 0.39 mN and Fz =0.12 mN, respectively. Positional errors remained below 2% in-plane and 6% out-of-plane. The fabricated device exhibits a minimum resonant frequency of 656 Hz, which is sufficient to capture short-duration impact events. Finally, droplet impact experiments are conducted under both vertical and tilted conditions. Compared with the vertical configuration, the inclined condition demonstrates Fx values comparable in magnitude to Fz and a clear elongation of the droplet induced by shear forces. Overall, the proposed force plate provides a customizable platform for high-precision, high-speed force measurements in droplet dynamics.
- 6 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (10) , 15095-15102
Two-Axis Transparent Force Plate for Droplet Collision Measurement Using High-Speed Line-Scan Camera and Sampling Moiré Method
Force measurement and interface observation during droplet impact are essential for understanding droplet behavior in both scientific and industrial applications. However, achieving both backside optical transparency for interface observation and two-axis force measurement for quantifying shear-force effects has been challenging with conventional force-sensing methods using a single device. In this study, we propose a transparent two-axis force plate based on the sampling moiré (SM) method combined with a line-scan camera, which enables high-temporal-resolution force measurement while permitting optical observation beneath the impacted surface. The proposed device consists of a spring-supported, laser-cut glass plate with a periodic striped pattern and a prism-based optical system. A line-scan camera is employed to overcome the inherent trade-off between spatial resolution and frame rate associated with area-scan cameras. By duplicating the pattern image using a prism and analyzing the resulting displacements via the SM method, in-plane and out-of-plane forces are independently measured from one-dimensional images. Calibration experiments confirm linear force–displacement characteristics, with force resolutions of Fx = 0.39 mN and Fz =0.12 mN, respectively. Positional errors remained below 2% in-plane and 6% out-of-plane. The fabricated device exhibits a minimum resonant frequency of 656 Hz, which is sufficient to capture short-duration impact events. Finally, droplet impact experiments are conducted under both vertical and tilted conditions. Compared with the vertical configuration, the inclined condition demonstrates Fx values comparable in magnitude to Fz and a clear elongation of the droplet induced by shear forces. Overall, the proposed force plate provides a customizable platform for high-precision, high-speed force measurements in droplet dynamics.
- 15 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Letters
- Vol. 9 (10) , 1-4
Corrugated Glass Diaphragm Differential Pressure Sensor Using Sampling Moiré Method
Various types of pressure sensors have been developed because pressure monitoring is essential in a variety of fields. Among these, optical methods have attracted attention due to their high sensitivity and low drift; however, they often require complex setups. Recently, the sampling Moiré (SM) method has emerged as an optical measurement technique, offering both simplicity and high resolution. In this letter, we propose a vision-based differential pressure sensor using the SM method. The proposed sensor consists of a corrugated glass diaphragm with a stripe pattern, a right-angle prism, and a microcontroller-based board camera. From the images of the stripe pattern captured before and after diaphragm displacement, the applied differential pressure is calculated using the SM method. We designed and fabricated a corrugated glass diaphragm with a thickness of 50 µm using laser processing. A stripe pattern with a pitch of 0.4 mm was formed at the center of the diaphragm. Then, the sensor was fabricated by assembling the corrugated glass diaphragm, the prism, and the camera. The pressure calibration experiments were conducted to evaluate the sensor response. When a differential pressure of −200 to +200 Pa was applied to the sensor, the measured displacement was linear, with a resolution of less than 10 Pa. These results suggest that the proposed vision-based sensor can effectively measure differential pressure with a simple setup.
- 15 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Letters
- Vol. 9 (10) , 1-4
Corrugated Glass Diaphragm Differential Pressure Sensor Using Sampling Moiré Method
Various types of pressure sensors have been developed because pressure monitoring is essential in a variety of fields. Among these, optical methods have attracted attention due to their high sensitivity and low drift; however, they often require complex setups. Recently, the sampling Moiré (SM) method has emerged as an optical measurement technique, offering both simplicity and high resolution. In this letter, we propose a vision-based differential pressure sensor using the SM method. The proposed sensor consists of a corrugated glass diaphragm with a stripe pattern, a right-angle prism, and a microcontroller-based board camera. From the images of the stripe pattern captured before and after diaphragm displacement, the applied differential pressure is calculated using the SM method. We designed and fabricated a corrugated glass diaphragm with a thickness of 50 µm using laser processing. A stripe pattern with a pitch of 0.4 mm was formed at the center of the diaphragm. Then, the sensor was fabricated by assembling the corrugated glass diaphragm, the prism, and the camera. The pressure calibration experiments were conducted to evaluate the sensor response. When a differential pressure of −200 to +200 Pa was applied to the sensor, the measured displacement was linear, with a resolution of less than 10 Pa. These results suggest that the proposed vision-based sensor can effectively measure differential pressure with a simple setup.
- 11 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (18) , 34480-34490
Triaxial Micro Force Plate Array for Measuring Ground Reaction Force in Ant Locomotion
Terrestrial insects, such as ants, are known for their agile locomotion on six legs. However, the ground reaction force (GRF) of each leg has not been well characterized due to its difficulty in measurement. In this report, a micro force plate array is presented that uses the sampling Moiré (SM) method, a prism, and a single camera to simultaneously measure the triaxial GRFs of multiple legs of an ant during its locomotion. The SM method is a high-resolution measurement method that measures the amount of displacement based on the shift of a captured grid pattern. The proposed micro force plate array consists of a$3 \times 3$ array of$2900 \times 2900 \times 70 \; \mu $ m plate bases with a gap of$100 \; \mu $ m as the contact surface of the ant legs. The plate base is supported by a spring structure with a grid pattern. By capturing this grid pattern from the backside via a prism, a camera can capture images from two different directions, allowing the triaxial displacement to be measured. By dividing the plate surface into nine sections and evaluating the error based on the position of the force application in the z-direction force, a maximum measurement error of 6% was found. The average force resolution in the x-, y-, and z-directions for the nine plates was 3.34, 2.47, and$1.20 \; \mu $ N, respectively. With the developed force plate array, it was possible to measure the GRF of each leg simultaneously while the ant was walking.- 11 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (18) , 34480-34490
Triaxial Micro Force Plate Array for Measuring Ground Reaction Force in Ant Locomotion
Terrestrial insects, such as ants, are known for their agile locomotion on six legs. However, the ground reaction force (GRF) of each leg has not been well characterized due to its difficulty in measurement. In this report, a micro force plate array is presented that uses the sampling Moiré (SM) method, a prism, and a single camera to simultaneously measure the triaxial GRFs of multiple legs of an ant during its locomotion. The SM method is a high-resolution measurement method that measures the amount of displacement based on the shift of a captured grid pattern. The proposed micro force plate array consists of a$3 \times 3$ array of$2900 \times 2900 \times 70 \; \mu $ m plate bases with a gap of$100 \; \mu $ m as the contact surface of the ant legs. The plate base is supported by a spring structure with a grid pattern. By capturing this grid pattern from the backside via a prism, a camera can capture images from two different directions, allowing the triaxial displacement to be measured. By dividing the plate surface into nine sections and evaluating the error based on the position of the force application in the z-direction force, a maximum measurement error of 6% was found. The average force resolution in the x-, y-, and z-directions for the nine plates was 3.34, 2.47, and$1.20 \; \mu $ N, respectively. With the developed force plate array, it was possible to measure the GRF of each leg simultaneously while the ant was walking.- 8 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Letters
- Vol. 9 (9) , 1-4
Sampling Moiré Method-Based Weight Scale Utilizing Dual-Pitch Stripe Pattern for High Resolution and Wide Range
Continuous measurement of the body mass of seabird chicks during the nestling period is valuable for investigating their growth ecology. To periodically measure their body mass without excessive disturbance, weight scales have been installed inside nests that have been constructed previously. Conventional weight scales had difficulty with low output drift and maintaining low power consumption. A force plate utilizing the sampling Moiré (SM) method, achieving high resolution and drift robustness in human use, was proposed. An applied force was calculated from a displacement detected by analyzing the stripe pattern captured by a camera. However, if there is a change of more than half the pattern pitch between frames, it cannot be measured correctly. Then, we propose an SM method-based weight scale that can be installed in nests and is suitable for time-lapse measurements, reducing power consumption. The proposed weight scale comprises a top plate supported with springs, an optical prism, and a microcontroller-based camera board. A dual-pitch stripe pattern, incorporating both short- and wide-pitch components, is attached to the backside of the top plate. Plate displacement is measured by analyzing images of the stripe pattern captured through the prism. Correction of the short-pitch results using the long-pitch results resolves phase wrapping and enables both high resolution and a wide measurement range. Calibration experiments of the developed weight scale demonstrated that the dual-pitch approach measured weights up to 2 kg while maintaining a high resolution of 45 mN, which corresponds to 4.6 g. The proposed weight scale is suitable for time-lapse monitoring of body mass in seabird chicks.
- 8 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Letters
- Vol. 9 (9) , 1-4
Sampling Moiré Method-Based Weight Scale Utilizing Dual-Pitch Stripe Pattern for High Resolution and Wide Range
Continuous measurement of the body mass of seabird chicks during the nestling period is valuable for investigating their growth ecology. To periodically measure their body mass without excessive disturbance, weight scales have been installed inside nests that have been constructed previously. Conventional weight scales had difficulty with low output drift and maintaining low power consumption. A force plate utilizing the sampling Moiré (SM) method, achieving high resolution and drift robustness in human use, was proposed. An applied force was calculated from a displacement detected by analyzing the stripe pattern captured by a camera. However, if there is a change of more than half the pattern pitch between frames, it cannot be measured correctly. Then, we propose an SM method-based weight scale that can be installed in nests and is suitable for time-lapse measurements, reducing power consumption. The proposed weight scale comprises a top plate supported with springs, an optical prism, and a microcontroller-based camera board. A dual-pitch stripe pattern, incorporating both short- and wide-pitch components, is attached to the backside of the top plate. Plate displacement is measured by analyzing images of the stripe pattern captured through the prism. Correction of the short-pitch results using the long-pitch results resolves phase wrapping and enables both high resolution and a wide measurement range. Calibration experiments of the developed weight scale demonstrated that the dual-pitch approach measured weights up to 2 kg while maintaining a high resolution of 45 mN, which corresponds to 4.6 g. The proposed weight scale is suitable for time-lapse monitoring of body mass in seabird chicks.
- 24 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. PP (1530437X) , 1
Optical Cantilever for High-Resolution Displacement Measurement Using Diffraction Grating and Sampling Moiré Method
Cantilever-type sensors play a critical role in precision measurement across various fields. Among the available detection principles, the optical lever method detects minute cantilever displacements via the reflection angle of a laser, achieving high-resolution displacement and force detection. Generally, a bi-cell or quadrant photodiode is used, and the reflected light must be initially positioned at the center. Additionally, if the reflected light moves beyond the dividing line of the photodiode, measurement becomes impossible. Conversely, the sampling moiré method has attracted attention for similar optical displacement measurement methods. The sampling moiré method enables high-resolution displacement measurement of the captured periodic pattern. The periodic pattern is captured in camera images, eliminating the need to adjust the light centered on photodiodes, and the detectable range of displacement in the sensing mechanism is not limited. This study proposes a measurement method that integrates the optical lever and the sampling moiré methods using a glass cantilever with a diffraction grating. When the cantilever is irradiated with a laser light, the grating diffracts the reflected light at the cantilever surface, forming a diffraction pattern. As the cantilever is deformed, the diffraction pattern shift is captured by a camera and analyzed using the sampling moiré method, yielding the displacement value. In experiment, the diffraction pattern spanning over approximately 200 μm was captured by a lens-less camera. With a cantilever displacement of 4 μm, the diffraction pattern captured by the camera shifted by 80 μm, corresponding to a 20-fold amplification of the cantilever displacement. The resolution of cantilever displacement, determined through an analysis of patten shifts, was calculated to be under 3.5 nm. The proposed method offers a robust and adjustment-free technique for cantilever-type sensor measurements.
- 24 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. PP (1530437X) , 1
Optical Cantilever for High-Resolution Displacement Measurement Using Diffraction Grating and Sampling Moiré Method
Cantilever-type sensors play a critical role in precision measurement across various fields. Among the available detection principles, the optical lever method detects minute cantilever displacements via the reflection angle of a laser, achieving high-resolution displacement and force detection. Generally, a bi-cell or quadrant photodiode is used, and the reflected light must be initially positioned at the center. Additionally, if the reflected light moves beyond the dividing line of the photodiode, measurement becomes impossible. Conversely, the sampling moiré method has attracted attention for similar optical displacement measurement methods. The sampling moiré method enables high-resolution displacement measurement of the captured periodic pattern. The periodic pattern is captured in camera images, eliminating the need to adjust the light centered on photodiodes, and the detectable range of displacement in the sensing mechanism is not limited. This study proposes a measurement method that integrates the optical lever and the sampling moiré methods using a glass cantilever with a diffraction grating. When the cantilever is irradiated with a laser light, the grating diffracts the reflected light at the cantilever surface, forming a diffraction pattern. As the cantilever is deformed, the diffraction pattern shift is captured by a camera and analyzed using the sampling moiré method, yielding the displacement value. In experiment, the diffraction pattern spanning over approximately 200 μm was captured by a lens-less camera. With a cantilever displacement of 4 μm, the diffraction pattern captured by the camera shifted by 80 μm, corresponding to a 20-fold amplification of the cantilever displacement. The resolution of cantilever displacement, determined through an analysis of patten shifts, was calculated to be under 3.5 nm. The proposed method offers a robust and adjustment-free technique for cantilever-type sensor measurements.