Walid Musrati
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Walid Musrati has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Bojan Medjo
University of Belgrade, Faculty of Technology and Metallurgy, Belgrade, Serbia
3 shared publications - Aleksandar Sedmak
University of Belgrade, Faculty of Mechanical Engineering, Belgrade, Serbia
2 shared publications - Nenad Gubeljak
University of Maribor, Faculty of Mechanical Engineering, Maribor, Slovenia
2 shared publications - Darko M. Veljić
Innovation Center of the Faculty of Technology and Metallurgy in Belgrade, Serbia
1 shared publication Darko Veljić
IHIS Techno Experts Research & Development Center, Batajnički drum 23, Belgrade 11000, Serbia
1 shared publication- Ivana Cvijović-Alagić
Center of Excellence “CEXTREME LAB”, Vinča Institute of Nuclear Sciences - National Institute of the Republic of Serbia, University of Belgrade, Belgrade, Serbia
1 shared publication
Latest Publications
- 15 May 2024
- Published by Society for Structural Integrity and Life "Prof. dr Stojan Sedmak" in Structural Integrity and Life
- Vol. 24 (1) , 105-110
Numerical simulation of friction stir welding - the plunge stage in T-joint
This paper deals with the tool plunge stage of friction stir welding which precedes the formation of the T-joint. A three-dimensional numerical model, developed in software package Simulia Abaqus® is applied for numerical analysis. The material of the welding plates is high strength aluminium alloy 2024-T3 of 3 mm thickness. The change of thermomechanical conditions in the welding zones has been analysed, as well as the conditions for eliminating the joining line in the weld root. The tool rotation speed and shoulder plunge depth are varied. Two tools are used for analysis with different tool pin lengths: 2.6 mm and 3 mm. Increase in tool rotation speed raises the temperature in the welding zone and creates conditions for eliminating the joining line in the weld root. In addition, the increased tool pin length is also beneficial. It is obtained that the tool rotation speed exceeding 500 min–1 is necessary for this joint and tool geometries.
- 15 May 2024
- Published by Society for Structural Integrity and Life "Prof. dr Stojan Sedmak" in Structural Integrity and Life
- Vol. 24 (1) , 105-110
Numerical simulation of friction stir welding - the plunge stage in T-joint
This paper deals with the tool plunge stage of friction stir welding which precedes the formation of the T-joint. A three-dimensional numerical model, developed in software package Simulia Abaqus® is applied for numerical analysis. The material of the welding plates is high strength aluminium alloy 2024-T3 of 3 mm thickness. The change of thermomechanical conditions in the welding zones has been analysed, as well as the conditions for eliminating the joining line in the weld root. The tool rotation speed and shoulder plunge depth are varied. Two tools are used for analysis with different tool pin lengths: 2.6 mm and 3 mm. Increase in tool rotation speed raises the temperature in the welding zone and creates conditions for eliminating the joining line in the weld root. In addition, the increased tool pin length is also beneficial. It is obtained that the tool rotation speed exceeding 500 min–1 is necessary for this joint and tool geometries.
- Open Access
- 1 January 2023
- Published by National Library of Serbia in Hemijska industrija
- Vol. 77 (2) , 155-165
Microstructure, hardness and fracture resistance of P235TR1 seam steel pipes of different diameters
Steel pipelines in industrial plants consist of different elements, including seamless and/or welded (seam) pipes. Properties of welded pipes, including their fracture behaviour, depend on the characteristics of both, the base metal, and the weld metal. In this work, two seam pipes are considered having different diameters and manufactured of P235TR1 steel. Hardness and microstructure were examined on the samples which contained the seam zone, to capture the influence of heterogeneity. Fracture resistance of the pipeline material, i.e. of both base metals and both seams, was determined by experimental examination of the recently proposed Pipe ring notch bending specimens with sharp stress concentrators. Differences between the two tested pipes, including the influence of the heterogeneity caused by the welded joint, were determined by comparison of the crack growth resistance curves. Effects of the initial stress concentrator shape, sharp machined notch or fatigue pre-crack are discussed.
- 1 January 2023
- Published by National Library of Serbia in Hemijska industrija
- Vol. 77 (2) , 155-165
Open AccessMicrostructure, hardness and fracture resistance of P235TR1 seam steel pipes of different diameters
Steel pipelines in industrial plants consist of different elements, including seamless and/or welded (seam) pipes. Properties of welded pipes, including their fracture behaviour, depend on the characteristics of both, the base metal, and the weld metal. In this work, two seam pipes are considered having different diameters and manufactured of P235TR1 steel. Hardness and microstructure were examined on the samples which contained the seam zone, to capture the influence of heterogeneity. Fracture resistance of the pipeline material, i.e. of both base metals and both seams, was determined by experimental examination of the recently proposed Pipe ring notch bending specimens with sharp stress concentrators. Differences between the two tested pipes, including the influence of the heterogeneity caused by the welded joint, were determined by comparison of the crack growth resistance curves. Effects of the initial stress concentrator shape, sharp machined notch or fatigue pre-crack are discussed.
- Open Access
- 1 January 2018
- Published by Elsevier in Procedia Structural Integrity
- Vol. 13, 1828-1833
Fracture analysis of axially flawed ring-shaped bending specimen
- 1 January 2018
- Published by Elsevier in Procedia Structural Integrity
- Vol. 13, 1828-1833
Open AccessFracture analysis of axially flawed ring-shaped bending specimen