Iker Urresti
Research Subjects
Iker Urresti has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Iñigo Llanos
Ideko Research Centre, Arriaga industrialdea 2, E-20870 Elgoibar, Spain
2 shared publications A. Robles
1 shared publication- David Bilbatua
Danobat S. Coop., Arriaga Industrialdea 21, E-20870 Elgoibar, Spain
1 shared publication H. Zabala
Ikerlan Technology Research Centre, Basque Research and Technology Alliance (BRTA), Arrasate-Mondragon, Spain
1 shared publication- Iñaki Leciñana
Basque Res & Technol Alliance BRTA, IKERLAN Technol Res Ctr, Gipuzkoa, Spain
1 shared publication Iñigo Llanos
Ideko - Basque Research and Technology Alliance (BRTA), Elgoibar, Spain
1 shared publication
Latest Publications
- Open Access
- 19 November 2024
- Published by MDPI AG in Sustainability
- Vol. 16 (22) , 10078
Evaluation of Sustainability and Cost Effectiveness of Using LCO2 as Cutting Fluid in Industrial Hard-Turning Installations
Conventional oil-based emulsions used in hard-turning processes present significant environmental and economic challenges, including high waste generation and hazardous disposal requirements. In response, cryogenic CO2 cooling has gained attention as a sustainable alternative, offering improved productivity, reduced tool wear and a diminished environmental footprint. While technical advances have been reported, the industrial adoption of cryogenic cooling is still limited due to the lack of clear data on its actual viability. This paper moves beyond the analysis of the technical performance of cryogenic CO2 cooling analyzed in previous works to conduct a detailed evaluation of its environmental and economic performance when machining roller bearing components with pCBN tools on a hard-turning installation. Utilizing Life Cycle Assessment (LCA) and Return-on-Investment (ROI) methodologies, this study compares cryogenic CO2 with traditional cooling methods, quantitatively assessing the environmental impact and economic viability across different manufacturing scenarios. The findings reveal that cryogenic cooling can outperform conventional cooling regarding both environmental impact and cost-effectiveness thanks to the tool life improvements provided by cryogenic cooling, specifically in cases where high tool consumption is generated during hard-turning operations. These results provide critical insights for selecting cooling strategies during the design phase of industrial turnkey projects, highlighting the potential of cryogenic CO2 as a superior solution for sustainable and efficient hard-turning operations.
- 19 November 2024
- Published by MDPI AG in Sustainability
- Vol. 16 (22) , 10078
Open AccessEvaluation of Sustainability and Cost Effectiveness of Using LCO2 as Cutting Fluid in Industrial Hard-Turning Installations
Conventional oil-based emulsions used in hard-turning processes present significant environmental and economic challenges, including high waste generation and hazardous disposal requirements. In response, cryogenic CO2 cooling has gained attention as a sustainable alternative, offering improved productivity, reduced tool wear and a diminished environmental footprint. While technical advances have been reported, the industrial adoption of cryogenic cooling is still limited due to the lack of clear data on its actual viability. This paper moves beyond the analysis of the technical performance of cryogenic CO2 cooling analyzed in previous works to conduct a detailed evaluation of its environmental and economic performance when machining roller bearing components with pCBN tools on a hard-turning installation. Utilizing Life Cycle Assessment (LCA) and Return-on-Investment (ROI) methodologies, this study compares cryogenic CO2 with traditional cooling methods, quantitatively assessing the environmental impact and economic viability across different manufacturing scenarios. The findings reveal that cryogenic cooling can outperform conventional cooling regarding both environmental impact and cost-effectiveness thanks to the tool life improvements provided by cryogenic cooling, specifically in cases where high tool consumption is generated during hard-turning operations. These results provide critical insights for selecting cooling strategies during the design phase of industrial turnkey projects, highlighting the potential of cryogenic CO2 as a superior solution for sustainable and efficient hard-turning operations.
- Open Access
- 2 May 2023
- Published by Elsevier in Procedia CIRP
- Vol. 117, 86-91
Surface Integrity Modelling for Cryogenic-assisted Hard Turning: A hybrid approach
- 2 May 2023
- Published by Elsevier in Procedia CIRP
- Vol. 117, 86-91
Open AccessSurface Integrity Modelling for Cryogenic-assisted Hard Turning: A hybrid approach
- Open Access
- 9 December 2021
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 98 (6) , 739-757
Lifetime prediction of bonded structural patch repairs for wind turbine pitch bearing strengthening
There is a growing trend in the use of adhesively bonded patches to repair structures that are subjected to fatigue loads in an attempt to reduce the propagation of an existing crack. The fatigue lifetime prediction of the adhesive used in bonded patch repair is a state-of-the-art challenge, especially when in-service conditions must also be considered. Different approaches have been identified in the literature to analyse structural failure; the methods based on fracture mechanics seem more promising for adhesives because the presence of defects is also considered in the analysis. A considerable amount of work has been undertaken to analyse the delamination of layered structures using cohesive zone modelling (CZM). However, research analysing fatigue delamination in bonded thick-walled structures (> 30 mm) is lacking. The present work proposes a methodology to predict the lifetime of an adhesively bonded patch repair applied to a thick-walled structure, specifically looking at the bearing ring structural fatigue (RSF) life extension of a pitch bearing commonly used in wind turbines.
- 9 December 2021
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 98 (6) , 739-757
Open AccessLifetime prediction of bonded structural patch repairs for wind turbine pitch bearing strengthening
There is a growing trend in the use of adhesively bonded patches to repair structures that are subjected to fatigue loads in an attempt to reduce the propagation of an existing crack. The fatigue lifetime prediction of the adhesive used in bonded patch repair is a state-of-the-art challenge, especially when in-service conditions must also be considered. Different approaches have been identified in the literature to analyse structural failure; the methods based on fracture mechanics seem more promising for adhesives because the presence of defects is also considered in the analysis. A considerable amount of work has been undertaken to analyse the delamination of layered structures using cohesive zone modelling (CZM). However, research analysing fatigue delamination in bonded thick-walled structures (> 30 mm) is lacking. The present work proposes a methodology to predict the lifetime of an adhesively bonded patch repair applied to a thick-walled structure, specifically looking at the bearing ring structural fatigue (RSF) life extension of a pitch bearing commonly used in wind turbines.
- 1 January 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1960 (1) , 070026
High productivity mould robotic milling in Al-5083
Industrial serial robots were usually limited to welding, handling or spray painting operations until very recent years. However, some industries have already realized about their important capabilities in terms of flexibility, working space, adaptability and cost. Hence, currently they are seriously being considered to carry out certain metal machining tasks. Therefore, robot based machining is presented as a cost-saving and flexible manufacturing alternative compared to conventional CNC machines especially for roughing or even pre-roughing of large parts. Nevertheless, there are still some drawbacks usually referred as low rigidity, accuracy and repeatability. Thus, the process productivity is usually sacrificed getting low Material Removal Rates (MRR), and consequently not being competitive. Nevertheless, in this paper different techniques to obtain increased productivity are presented, though an appropriate selection of cutting strategies and parameters that are essential for it. During this research some rough milling tests in Al-5083 are presented where High Feed Milling (HFM) is implemented as productive cutting strategy and the experimental modal analysis named Tap-testing is used for the suitable choice of cutting conditions. Competitive productivity rates are experienced while process stability is checked through the cutting forces measurements in order to prove the effectiveness of the experimental modal analysis for robotic machining.
- 1 January 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1960 (1) , 070026
High productivity mould robotic milling in Al-5083
Industrial serial robots were usually limited to welding, handling or spray painting operations until very recent years. However, some industries have already realized about their important capabilities in terms of flexibility, working space, adaptability and cost. Hence, currently they are seriously being considered to carry out certain metal machining tasks. Therefore, robot based machining is presented as a cost-saving and flexible manufacturing alternative compared to conventional CNC machines especially for roughing or even pre-roughing of large parts. Nevertheless, there are still some drawbacks usually referred as low rigidity, accuracy and repeatability. Thus, the process productivity is usually sacrificed getting low Material Removal Rates (MRR), and consequently not being competitive. Nevertheless, in this paper different techniques to obtain increased productivity are presented, though an appropriate selection of cutting strategies and parameters that are essential for it. During this research some rough milling tests in Al-5083 are presented where High Feed Milling (HFM) is implemented as productive cutting strategy and the experimental modal analysis named Tap-testing is used for the suitable choice of cutting conditions. Competitive productivity rates are experienced while process stability is checked through the cutting forces measurements in order to prove the effectiveness of the experimental modal analysis for robotic machining.