HZHengji Zhang

Hengji Zhang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Hengji Zhang has a total of 17 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Study on Binder Film Thickness Distribution of Recycled Asphalt Pavements

    by Hengji Zhang, John T. Harvey, Liya Jiao, Hui Li, Mohamed Elkashef

    Binder film thickness (BFT) plays a vital role during the design of asphalt mixture and fine aggregate matrix because BFT can exert a significant effect on the performance of asphalt materials. However, the surface area factors are affected by the different specific gravities of the aggregates, which are always ignored during the calculation of BFT. Moreover, whether the BFT is uniformly distributed in asphalt mixture is controversial. Hence, it is necessary to further study the distribution of asphalt film thickness in asphalt materials and its influence factor. This study analyzed the distribution of BFT in coarse and fine parts of recycled asphalt pavements (RAPs). Firstly, a part of four types of RAP (Teichert, Syar, Vulcan coarse, and Vulcan fine) were sieved by #8 sieve (2.36 mm) to achieve coarse and fine parts of RAP. Secondly, the binder content and aggregate gradation were investigated through the ignition and extraction method. Thirdly, surface area ratio was used to evaluate the influence of the ignition and extraction method on the surface area of aggregate sieved from RAP. Finally, the BFT of different types of RAP were calculated through two different methods to evaluate the effect of specific gravities of the aggregates on BFT. The results indicate that for the coefficient of variation, 30 out of 32 data were less than 15.0 %, which implies the BFT was almost evenly distributed in coarse and fine parts of RAP. In addition, the difference of surface area factors caused by the different specific gravities of the aggregates exerts negligible influence on the surface area and the calculation of BFT.


  • Optimum Filler–Bitumen Ratio of Asphalt Mortar Considering Self-Healing Property

    by Hengji Zhang, Hui Li, Ahmed Abdelhady, Dingcheng Mo, Bing Yang, John Harvey

    Asphalt mortar plays an important role in the performance of asphalt mixtures. Up to now, there have been many studies on the properties of asphalt mortar. However, asphalt mortar requires a balanced design that considers the overall performance including self-healing capability. Therefore, this study aims to analyze the effect of different types of filler with varied ratios (0.11, 0.22, 0.33, 0.44, and 0.55) by volume on the performance of the asphalt mortar and mixture. The examined fillers were limestone, fly ash, diatomite, and four types of red mud, which were mixed with bitumen to prepare asphalt mortar. Then, the rheological properties of the asphalt mortar were investigated through viscosity tests and multiple stress creep recovery (MSCR) testing. In addition, this research explores the impact of filler type and its ratio on the cohesion and self-healing performance in dry and water conditions. Furthermore, the Hamburg wheel tracking test (HWTT) was performed to evaluate the moisture-damage and rutting resistance of asphalt mixtures, which consisted of the same selected mortar. The results indicate that pull-off tensile strength after the first failure-healing (F-H) cycle in the water condition has a good linear relationship with the dynamic stability of the asphalt mixture in the HWTT. Moreover, red mud and diatomite can be applied as promising substitute fillers compared with the other examined fillers in this study, but the chemical components need to be carefully selected.


  • Utilization of Fine Solid Waste in Asphalt Mortar

    by Hengji Zhang, Hui Li, Ahmed Abdelhady, Dingcheng Mo, John Harvey

    Asphalt mortar consists of asphalt and filler and exerts a vital influence on the performance of asphalt materials. Nowadays, plenty of fine solid waste with extremely different physical and chemical properties has been reused in asphalt materials. Therefore, this study aims to analyze the effect of reusing fine solid waste as filler on the performance of asphalt mortar and investigate the possibility of utilizing the fine solid waste in asphalt mortar. Firstly, a scanning electron microscope was used to investigate the microstructure of limestone ore powder, fly ash, diatomite, and red mud. Secondly, the workability, high temperature property, and adhesion ability of asphalt mortars with different filler types and volume ratios have been examined. Thirdly, a critical filler-bitumen ratio range was recommended in view of the aforesaid performances. Finally, analysis of variance was applied to study the relationship between the relative performance of asphalt mortar and physical properties of filler. The results indicated that the Rigden Void of the filler exerts an important influence on the workability and high temperature performance of asphalt mortar, while no significant effect was observed on the elastic and adhesion capacity of the asphalt mortar. Hence, the Rigden Void can be considered a more effective index than the fineness modulus to describe the geometric features of fillers. In addition, asphalt mortar with diatomite and red mud exhibited improvement in the high temperature property and adhesion ability in the case of dry and moist conditions.