MZMikhail Mikhailovich Zhileikin

Mikhail Mikhailovich Zhileikin

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Mikhail Mikhailovich Zhileikin has a total of 36 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Experimental validation of a physically based mathematical model of wheel rolling motion on a solid supporting surface during rectilinear driving

    by M. M. Zhileykin, O. A. Kozelkov, A. A. Kosenkov, V. A. Neverov, М. М. Жилейкин, О. А. Козелков, А. А. Косенков, В. А. Неверов

    Introduction.  High-fidelity simulation of off-road and amphibious vehicle motion relies on accurate wheel-surface interaction models. Although empirical and semi-empirical wheel rolling models (Pacejka, Guo and Lu) are dominant on solid surfaces, their input parameters are often ambiguous and do not have a direct physical interpretation, it is significantly limiting their predictive capabilities under complex, multi-mode driving conditions. Expensive and time-consuming specific sample testing is often required to obtain accurate characteristics. Materials and Methods.  This study presents an experimental validation of a physically based wheel dynamics model for non-deformable supporting surfaces. The mathematical description of the tire model with the use of brush analogy has been previously presented. A laboratory test bench was used as a validation environment to measure wheel kinematics and dynamics under a wide range of vertical loads in both driving and driven modes. Key parameters, including rolling radius, longitudinal slip, and torque have been measured directly on the rig. Results.  Experimental data were used to validate the developed mathematical model, implemented in MATLAB/ Simulink. The model demonstrated match with experiment results in free-rolling mode, with a normalized root-meansquare error (RMS) below 1.2% for the covered distance. In driving mode, the error increased to approximately 10%, which, according to the analysis, is explained by the risen complexity of torque application and slip dynamics. Discussion and Conclusion.  Unlike purely empirical models, all parameters of the developed model have a clear physical meaning and can be determined from a limited set of experiments. It makes this model a preferred choice for problems requiring the behavior prediction under various conditions.

  • Open Access

    Lyapunov-based Model for Modern Stabilization Systems of All-wheel Drive Vehicles

    by Mikhail M. Zhilejkin, Oleg A. Kozelkov, Vsevolod A. Neverov

    The study develops a mathematical model of vehicle stability with torque redistribution, aimed at ensuring guaranteed stabilization under non-stationary conditions. Unlike existing methods, the approach combines Lyapunov functions with bifurcation analysis to derive analytical stability criteria for vehicles with mechanical differentials and enables the synthesis of adaptive control strategies that integrate differential locking, wheel braking, and dynamic torque redistribution with formal stability guarantees. The model provides accurate calculations of torque redistribution to the inner or outer wheels during vehicle oversteer or understeer, respectively, ensuring motion stabilization and preserves stability even under sharp steering inputs, as confirmed by phase portraits and transient response analyses. The proposed model was implemented and verified. The model can be incorporated into active safety systems of wheeled vehicles to enhance stability on complex surfaces, reduce computational requirements, and ensure compatibility with existing mechanical drivetrains.

  • Open Access

    Use of a neural network for estimation of vertical force in contact patch for energy efficiency improvement

    by Mikhail M. Zhileikin, Жилейкин Михаил Михайлович

    BACKGROUND: More efficient on-board energy consumption has allowed hybrid powertrains to become firm in the market. The conditions for using a hybrid powertrain as part of small-scale mechanization vehicles intended for off-road use differ significantly from the conditions for use in road vehicles. The development of this type of transmission design, the control system and the algorithm for its efficient operation is a relevant technical problem. AIM: Study of the possibilities of using neural network learning in estimating the vertical force in contact patches of wheels to create algorithms for efficient control of the hybrid powertrain of an all-terrain vehicle. METHODS: Modeling of operation conditions is performed in the MATLAB software and its applications Simulink and Neural Network. Using fundamental blocks of these applications, a model of the hybrid-powered three-axle all-terrain vehicle motion on uneven solid support surface is built. RESULTS: Based on the results of testing the work of the trained neural network, using the simulation modeling method, a conclusion was made about the sufficient accuracy of the indirect estimation method. The root-mean-square deviation of the determined forces from those obtained in the motion model was 9.5%. CONCLUSION: The practical value of the study lies in the possibility of using the proposed approach to determining the vertical force in the contact patch of the wheel with a solid support surface when developing laws for the efficient control of the electric drive of the third axle of an all-terrain vehicle with a hybrid powertrain.


  • Study of the stability of motion in water of amphibious wheeled transport and technological units in the hydroplaning mode

    by Oleg A. Kozelkov, Mikhail M. Zhilejkin, Timur V. Kondratenko, Vsevolod A. Neverov

    BACKGROUND: Amphibious wheeled transport and technological units (AWTTU) are critically important for rescues and other special operations, but their velocity in water is limited due to high wheel resistance and suboptimal hydrodynamics. Existing studies do not take into account the hydroplaning mode in a comprehensive manner. AIM: Development of a mathematical model of the motion in water of an amphibious vehicle in the hydroplaning mode, which takes into account both hydrostatic and hydrodynamic forces. METHODS: Equations for determining excess pressure on the hull surface are derived based on the Cauchy-Lagrange integral, a calculation scheme for the interaction of a flat-bottomed hull with the water surface is developed. Analytical expressions for the lifting hydrodynamic force, resistance force, and hydrodynamic moment are obtained. An analysis of the stability of motion is carried out taking into account the position of the center of gravity, the magnitude of the traction force of the watercraft propeller, and the trim angle. RESULTS: It was found that at Froude numbers Fr 3.0, hydrodynamic forces ensure 95–97% of sustaining the AWTTU afloat. The criteria for the motion stability are obtained: with a negative arm of the propulsion force, the stability depends on the magnitude of the thrust, with a positive arm, the critical speed of motion is determined. It was found that the thickness of the “reverse jet” is proportional to the angle of attack, the resistance force has a quadratic dependence on the velocity, the arm of the hydrodynamic moment is linearly dependent on the trim angle. CONCLUSION: The developed mathematical model allows analyzing the motion of the AWTTU in the hydroplaning mode taking into account key hydrodynamic factors. The obtained results create a theoretical basis for the design of high-velocity amphibious vehicles and require further experimental validation.

  • Open Access

    Complex model of the dynamics of a multi-axle wheeled amphibious vehicle to improve stability and handling in transient and extreme conditions

    by Mikhail M. Zhilejkin, Oleg A. Kozelkov, Vsevolod A. Neverov

    BACKGROUND: The dynamics of multi-axle amphibious wheeled transport and technological vehicles (AWTTV) remain poorly understood, especially under variable grip and extreme driving conditions. Existing studies focus primarily on two- and four-axle vehicles, ignoring complex nonlinear effects of tire slip and interaction between axles, which limit control accuracy for heavy multi-axle vehicles. AIM: Development of a complex mathematical model of AWTTV dynamics that combines torque distribution between axles, real-time correction of wheel steering angles, and consideration of nonlinear effects of slip, to improve stability and handling in transient and extreme conditions. METHODS: The following methods are used in the research: theoretical and analytical study based on the equations of vehicle dynamics, simulation modeling of the motion of an AWTTV with an 8x8 wheel arrangement, comparative analysis of two steering schemes (1-2-0-0 and 1-2-3-4), assessment of the influence of velocity, acceleration and steer angles on stability, verification of the model by means of the analysis of steady-state and transient modes. RESULTS: It was found that the difference in the slip angles of the outer axles increases proportionally to the velocity and the steer angle, reaching 10 degrees at a velocity of 40 km/h. Deviation from the specified path for the 1-2-0-0 scheme reaches 40%, which is 1.6 times higher than for the 1-2-3-4 scheme. In transient modes, an increase in the difference in slip angles by 15-20% was observed compared to the steady-state mode. CONCLUSION: The proposed model demonstrates that the integration of torque distribution and active steering reduces the path deviation and improves the stability of the AWTTV. The results highlight the need for adaptive algorithms for multi-axle vehicles, especially in transient conditions.

  • Open Access

    A highway road train motion model validation based on the experimental studies results of vibration acceleration processes in the truck cabin with suspension system

    by Roman Olegovich Maksimov, Mikhail Mikhailovich Zhileykin, Yury Sergeevich Shchetinin, Vladislav V. Bernatsky, Yury Mikhailovich Furletov, Жилейкин Михаил Михайлович, Фурлетов Юрий Михайлович

    BACKGROUND: The research solves the problem of validating the spatial motion multibody dynamic model of a complete highway road train with spring cabin truck in order to prove its applicability as a tool for analyzing and evaluating the vehicle operational properties and researching their improvement methods. AIM: Conducting a set of highway road train field tests to obtain experimental data on vibration acceleration processes in a truck cabin with suspension followed by an its operational properties analysis and evaluation according to the comfort criteria, and conducting a results-based validation procedure for the spatial motion multibody dynamic model of a complete highway road train developed as a toolkit for vehicle virtual testing. METHODS: The work uses methods of experimental research of a real highway ground vehicle at the road surface using measuring equipment in order to obtain experimental data for analyzing the highway road train dynamics operational parameters. RESULTS: The experimental data obtained in the form of vibration acceleration processes in the sprung truck cab form the validation basis of the research and are used during the vehicle motion model validation procedure to compare and determine whether the behavior of the highway road train dynamics model corresponds to the real world in the claimed field of application. CONCLUSION: According to the results of the vehicle spatial motion simulation model validation, which was the aim of this study, it is found that the normalized RMS errors of the simulation characteristics according to the “comfort” criterion are less than 10%, which corresponds to measurement errors for analyzing vibration load and vehicle comfort and indicates the research objective achievement. The multibody model of a highway road train can be used as a tool for analyzing the vehicle comfort, as well as for evaluating the effectiveness and operability of methods for improving comfort in cargo ground vehicles and the vibration-insulating properties of their suspension systems according to comfort criteria with an error of less than 10%.

  • Open Access

    Mathematical Model of Cabin With Suspension System to Analyze its Oscillatory Stability During Vehicle Movement

    by Roman Maksimov, Mikhail Zhileykin, Aleksandr Klimov, Andrey Keller, Sergey Shadrin, Daria Makarova, Vladimir Ershov, Yury Furletov

    This research focuses on the development of a methodology for the analysis of nonlinear oscillations of a vehicle cab with a suspension system. When designing vehicles with cab suspension systems, it is important to align their operation with other vehicle modules and systems that collectively ensure the required comfort and dynamic parameters and prevent resonant oscillations in the cab. A vehicle cab is a dynamic system with 6 degrees of freedom, therefore its oscillations are spatially complex and feature energy direction switching. Thus, the problems of suspended cab dynamics should be solved in a non-linear spatial setting that can account for oscillation energy redistribution between various spatial direc-tions. The purpose of this work is to develop a mathematical model for the spatial oscillations of a suspended cab relative to the vehicle undercarriage that can help analyze the non-linear oscillations that occur in the cab to study their stability during vehicle movement. This study helped identify the adverse frequency ratios for the disturbing impact on the can suspension system that can reduce cab comfort and result in the instability of its oscillations. The authors developed methods to reduce the amplitudes of suspended cab sway when its spatial oscillations are unstable. The developed methods and mathematical model help identify and prevent resonant spatial phenomena in the cab at all stages of designing vehicle cab suspension systems. The authors proposed specific solutions to design cab suspension systems to improve cab comfort and reduce cab sway, including the usage of air bellows that can form progressive non-linear load characteristics and controllable hydraulic dampers that can increase the damping coefficient in the cab suspension system during cab sway.


  • Open Access

    Diagnostics of inter-turn short circuits in phase stator windings of permanent magnet synchronous machines

    by Mikhail M. Zhileykin, Aleksandr V. Klimov, Baurjan K. Ospanbekov, Stanislav S. Smirnov, Жилейкин Михаил Михайлович

    BACKGROUND: Currently, electric buses are becoming more widespread in the segment of urban passenger transportation due to the absence of harmful emissions and low noise levels. Permanent magnet synchronous machines (PMSM) are widely used as a traction motor. One of the most promising methods of monitoring the technical condition of traction motors is diagnostics using monitoring tools installed on board of a vehicle. The advantages of such methods include the possibility of regular frequent condition checks (as opposed to much rarer diagnostics in stationary maintenance points) and a more rapid response to the development of identified malfunctions, which significantly reduces the cost of maintenance and repair of expensive equipment. The disadvantages include limitations associated with a shortage of layout space for the placement of diagnostic equipment, with the limited capabilities of on-board computer facilities for the transmission and storage of diagnostic information and with the complexity of computational procedures of built-in expert diagnostic systems. Concerning the types of operational failures of PMSMs, which are the most common and the most severe in terms of the cost of restoring operability, these are inter-turn short circuits in the stator windings, increased eccentricity of the air gap between the stator and the rotor, bearing damage, as well as damage of the mechanical gearbox coupled with the electric motor. AIM: Identification the diagnostic signs of inter-turn short circuits in the phase windings of a permanent magnet synchronous machine, helping to detect these malfunctions on board of route urban vehicles at an early stage. METHODS: A mathematical model of a permanent magnet synchronous machine with short-circuited turns of the phase winding, which makes it possible to study the behavior of the motor with a various number of short-circuited turns, has been developed. RESULTS: For the first time, the requirements for diagnostic features for the on-board diagnostic system of an urban electric bus, making it possible to detect inter-turn short circuits in the phase windings of traction electric motors at the early stages of the origin of a malfunction, are formulated. The main parameters of the process of digital registration of phase currents have been obtained, helping to do measurements and to transmit signals through the onboard information network of the electric bus. Using simulation modeling methods, it was found that the peak values of the linear spectrum of the total current vector are stable diagnostic signs that make it possible to detect inter-turn short circuits in the phase windings of traction motors at the early stages of the origin of the malfunction. CONCLUSION: The practical value of the study lies in the opportunity of using the proposed methods for diagnosing the technical condition of traction electric drive units in urban passenger electric transport.

  • Open Access

    Development and verification of a virtual prototype of a vehicle

    by Mikhail M. Zhileykin, Akop V. Antonyan, Yury M. Furletov, Жилейкин Михаил Михайлович

    BACKGROUND: Methods of mathematical modelling are widely used in vehicle development. In order to study vehicle dynamics, stability and handling, as well as to accelerate and to reduce the cost of on-board software development, it is necessary to build a digital twin which contains description of special motion of a vehicle with models of units and subsystems as parts of the vehicle. AIMS: Development and verification of a virtual prototype of a vehicle. METHODS: Development of the virtual prototype and vehicle modelling were done in the MATLAB/Simulink software package. Main derivation of the equations necessary to build the models of vehicle’s units and subsystems is given. Verification testing was conducted using special measuring equipment. RESULTS: The vehicle virtual prototype containing description of combined dynamics of bodyframe, transmission elements, suspension and wheels was developed. Comparison of results of field and virtual testing was made in order to confirm operability and adequacy of the virtual prototype. Main graphs showing dynamics of real and virtual vehicles are presented. CONCLUSIONS: Practical value of development and study lies in ability of using a virtual prototype in vehicle dynamic studies and development of on-board control systems.


  • Open Access

    Improving the stability and handling of tractors when towing trailers and coupled units

    by Mikhail M. Zhileykin, Pavel V. Sirotin, Sergey S. Nosikov, Жилейкин Михаил Михайлович

    BACKGROUND: Currently, almost all agricultural work is performed using tractors. As the transport speed of a tractor train increases, the amplitude of lateral and horizontal oscillations of its coupled units emerges and increases. At certain velocities, these oscillations become so large that they can lead to a rollover, in addition, shock loads occur in coupling devices, which make it difficult to handle a tractor train. The traditional method to prevent this is the velocity limit, which does not guarantee a positive result. AIMS: Development of methods to improve stability, handling and safety of wheeled tractor trains by reducing the galloping and yawing of a truck tractor when towing heavy loads. METHODS: The following options of the design of the system for countering the occurrence of self-oscillations in the design of a wheeled tractor train ensuring a reduction in the level of self-oscillations, increasing the stability, handling and safety of the tractor train have been proposed: the coupling device equipped with hydraulic damping devices operating at longitudinal and lateral folding; the control system for the individual traction electric drive of a truck tractor preventing the loss of wheel grip with the ground surface; the combined use of the control system for the individual traction electric drive of a truck tractor and the coupling device equipped with hydraulic damping devices; the combined use of the coupling device equipped with hydraulic damping devices and a steering correction system. RESULTS: With use of simulation modeling methods, it has been established that the coupling device equipped with hydraulic damping devices adjustable by the folding angle of the tractor train and by the yaw angle oscillations of a truck tractor body should be recognized as the most acceptable and effective system for reducing self-oscillations of a wheeled tractor train at the current state of the art. CONCLUSIONS: The practical value of the study lies in the possibility of using the proposed methods to eliminate the risk of self-oscillating processes in the design of promising types of agricultural machinery.