OKOleg A. Kozelkov

Oleg A. Kozelkov

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Oleg A. Kozelkov has a total of 17 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Experimental validation of a physically based mathematical model of wheel rolling motion on a solid supporting surface during rectilinear driving

    by M. M. Zhileykin, O. A. Kozelkov, A. A. Kosenkov, V. A. Neverov, М. М. Жилейкин, О. А. Козелков, А. А. Косенков, В. А. Неверов

    Introduction.  High-fidelity simulation of off-road and amphibious vehicle motion relies on accurate wheel-surface interaction models. Although empirical and semi-empirical wheel rolling models (Pacejka, Guo and Lu) are dominant on solid surfaces, their input parameters are often ambiguous and do not have a direct physical interpretation, it is significantly limiting their predictive capabilities under complex, multi-mode driving conditions. Expensive and time-consuming specific sample testing is often required to obtain accurate characteristics. Materials and Methods.  This study presents an experimental validation of a physically based wheel dynamics model for non-deformable supporting surfaces. The mathematical description of the tire model with the use of brush analogy has been previously presented. A laboratory test bench was used as a validation environment to measure wheel kinematics and dynamics under a wide range of vertical loads in both driving and driven modes. Key parameters, including rolling radius, longitudinal slip, and torque have been measured directly on the rig. Results.  Experimental data were used to validate the developed mathematical model, implemented in MATLAB/ Simulink. The model demonstrated match with experiment results in free-rolling mode, with a normalized root-meansquare error (RMS) below 1.2% for the covered distance. In driving mode, the error increased to approximately 10%, which, according to the analysis, is explained by the risen complexity of torque application and slip dynamics. Discussion and Conclusion.  Unlike purely empirical models, all parameters of the developed model have a clear physical meaning and can be determined from a limited set of experiments. It makes this model a preferred choice for problems requiring the behavior prediction under various conditions.

  • On-board diagnostics method for detecting bearing defects in traction synchronous permanent magnet motors based on stator current spectrum

    by E. A. Dvoeglazov, O. A. Kozelkov, P. K. Dyakov

    Introduction. The reliability of traction electric drive is a key factor determining the operational efficiency of urban electric transport. Bearing assemblies of electric motors remain one of the most common causes of failures leading to vehicle downtime. Materials and methods. A method has been developed for on-board diagnostics of rolling bearing defects in a traction synchronous motor with permanent magnets (SDM) based on the analysis of stator current spectrum (MCSA) with equivalent three-phase current used to normalize diagnostic features. In the study simulation modeling in the MATLAB/Simulink environment was carried out, covering the range of defect angular dimension from 0° to 8° and speeds from 1500 to 8000 rpm. Results. The method proposed sets clear limits to efficiency: the maximum speed for reliable defect detection is 5,000 rpm. At these and lower speeds in the stator current spectrum, a peak is observed of the mechanical rotor speed (fr), the amplitude of which correlates with the defect angular dimension. Normalization by equivalent operating current increases diagnostic accuracy. Discussion and conclusions. The proposed method makes it possible to implement an on-board diagnostic system without installing additional sensors, which is especially important for urban electric buses operating mainly in the range of 2000-5000 rpm. A new method has been developed that integrates normalization by equivalent operating current to quantify the diagnostic sensitivity of the analysis of the stator current spectrum depending on the rotor rotation speed in a permanent magnet synchronous motor and determines the critical speed threshold of 5000 rpm.

  • Open Access

    Lyapunov-based Model for Modern Stabilization Systems of All-wheel Drive Vehicles

    by Mikhail M. Zhilejkin, Oleg A. Kozelkov, Vsevolod A. Neverov

    The study develops a mathematical model of vehicle stability with torque redistribution, aimed at ensuring guaranteed stabilization under non-stationary conditions. Unlike existing methods, the approach combines Lyapunov functions with bifurcation analysis to derive analytical stability criteria for vehicles with mechanical differentials and enables the synthesis of adaptive control strategies that integrate differential locking, wheel braking, and dynamic torque redistribution with formal stability guarantees. The model provides accurate calculations of torque redistribution to the inner or outer wheels during vehicle oversteer or understeer, respectively, ensuring motion stabilization and preserves stability even under sharp steering inputs, as confirmed by phase portraits and transient response analyses. The proposed model was implemented and verified. The model can be incorporated into active safety systems of wheeled vehicles to enhance stability on complex surfaces, reduce computational requirements, and ensure compatibility with existing mechanical drivetrains.

  • Study of the stability of motion in water of amphibious wheeled transport and technological units in the hydroplaning mode

    by Oleg A. Kozelkov, Mikhail M. Zhilejkin, Timur V. Kondratenko, Vsevolod A. Neverov

    BACKGROUND: Amphibious wheeled transport and technological units (AWTTU) are critically important for rescues and other special operations, but their velocity in water is limited due to high wheel resistance and suboptimal hydrodynamics. Existing studies do not take into account the hydroplaning mode in a comprehensive manner. AIM: Development of a mathematical model of the motion in water of an amphibious vehicle in the hydroplaning mode, which takes into account both hydrostatic and hydrodynamic forces. METHODS: Equations for determining excess pressure on the hull surface are derived based on the Cauchy-Lagrange integral, a calculation scheme for the interaction of a flat-bottomed hull with the water surface is developed. Analytical expressions for the lifting hydrodynamic force, resistance force, and hydrodynamic moment are obtained. An analysis of the stability of motion is carried out taking into account the position of the center of gravity, the magnitude of the traction force of the watercraft propeller, and the trim angle. RESULTS: It was found that at Froude numbers Fr 3.0, hydrodynamic forces ensure 95–97% of sustaining the AWTTU afloat. The criteria for the motion stability are obtained: with a negative arm of the propulsion force, the stability depends on the magnitude of the thrust, with a positive arm, the critical speed of motion is determined. It was found that the thickness of the “reverse jet” is proportional to the angle of attack, the resistance force has a quadratic dependence on the velocity, the arm of the hydrodynamic moment is linearly dependent on the trim angle. CONCLUSION: The developed mathematical model allows analyzing the motion of the AWTTU in the hydroplaning mode taking into account key hydrodynamic factors. The obtained results create a theoretical basis for the design of high-velocity amphibious vehicles and require further experimental validation.

  • Open Access

    Complex model of the dynamics of a multi-axle wheeled amphibious vehicle to improve stability and handling in transient and extreme conditions

    by Mikhail M. Zhilejkin, Oleg A. Kozelkov, Vsevolod A. Neverov

    BACKGROUND: The dynamics of multi-axle amphibious wheeled transport and technological vehicles (AWTTV) remain poorly understood, especially under variable grip and extreme driving conditions. Existing studies focus primarily on two- and four-axle vehicles, ignoring complex nonlinear effects of tire slip and interaction between axles, which limit control accuracy for heavy multi-axle vehicles. AIM: Development of a complex mathematical model of AWTTV dynamics that combines torque distribution between axles, real-time correction of wheel steering angles, and consideration of nonlinear effects of slip, to improve stability and handling in transient and extreme conditions. METHODS: The following methods are used in the research: theoretical and analytical study based on the equations of vehicle dynamics, simulation modeling of the motion of an AWTTV with an 8x8 wheel arrangement, comparative analysis of two steering schemes (1-2-0-0 and 1-2-3-4), assessment of the influence of velocity, acceleration and steer angles on stability, verification of the model by means of the analysis of steady-state and transient modes. RESULTS: It was found that the difference in the slip angles of the outer axles increases proportionally to the velocity and the steer angle, reaching 10 degrees at a velocity of 40 km/h. Deviation from the specified path for the 1-2-0-0 scheme reaches 40%, which is 1.6 times higher than for the 1-2-3-4 scheme. In transient modes, an increase in the difference in slip angles by 15-20% was observed compared to the steady-state mode. CONCLUSION: The proposed model demonstrates that the integration of torque distribution and active steering reduces the path deviation and improves the stability of the AWTTV. The results highlight the need for adaptive algorithms for multi-axle vehicles, especially in transient conditions.

  • Investigation of the stability of the movement of mainline road trains with semi-trailers having a rotary controlled undercarriage module

    by Vlasov N. D., Jileykin M. M., Kozelkov O. A.

    In the modern world, the demand for highway transportation involving special vehicles is increasing every year. To solve such problems, two-link road trains are widely used due to their increased load capacity, cross-country ability and large dimensions of trailer and semi-trailer links, which make it possible to solve transport problems most effectively. When designing mainline road trains, they strive to maximize the length of trailed links with pivoting undercarriage modules. In this regard, a number of difficulties arise due to the need to improve the operational properties of road trains, such as maneuverability, controllability and stability of movement. However, despite the fact that semi-trailers with pivoting undercarriage modules are being manufactured and are in operation, the theoretical issues related to their stability and controllability in various driving conditions have not been sufficiently worked out. The purpose of the work is to study the stability of the movement of mainline road trains with semi-trailers having a rotary controlled undercarriage module. A study was conducted on the risks of loss of stability of mainline road trains with semi-trailers having a rotary controlled undercarriage module in various operating modes. It has been established that in order to ensure stable movement of the trailer link with a rotary support module, it is necessary to introduce corrective steering of the trolley in order to maintain the calculated folding angle of the road train and limit the angular folding speed of the road train.

  • Establishment of harmonized requirements for the transport of dangerous goods by road

    by Kirillov K. A.

    The current and future state in the field of tests of shells and fittings of tanks for the transport of dangerous goods for the purpose of improving road safety is analyzed. The conclusions contain proposals for further ways of action by domestic manufacturers of tankers&equipment for the transport of dangerous goods.

  • Comparative assessment of the level of road safety on routes

    by Pogodaev A. K., Evtyukov S. A., Klyavin V. E., Syisoev A. S., Jihoreva S. V.

    The possibility of assessing the level of road safety of traffic routes formed to service transport and logistics systems is considered. The assessment methodology allows not only identifying the risks of emergency situations on the formed route, but also determining the necessary measures to reduce these risks on the most problematic sections of the route.

  • Planning the volume of procurements of car spare parts during state and municipal procurements

    by Zagorskiy I.O. Lanyugova A.E.

    The article discusses methods for calculating the required number of spare parts, which allow you to save budget funds. A classification of consumption rates for spare parts is given. The parameters of the forecast model for the number of spare parts were calculated using the extrapolation method. Keywords planning, spare parts, state and municipal procurement, costs, forecast

  • Establishment of harmonized requirements for the transport of dangerous goods by road. Chapter 1

    by Anikeev S.A. Petrakov A.M. Kirillov K.A.

    Statistics on road accidents (crashes) with wheeled vehicles intended for the transport of dangerous goods have been collected and analysed. Proposals have been developed to reduce the severity of the consequences of such accidents. Recommendations are made on development directions for the purpose of improving road safety. The current and prospective state of conformity assessment of tank vehicles for the transport of dangerous goods is analysed. Keywords dangerous goods, accident, road safety, ADR, tank-vehicles