Yuefeng Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yuefeng Li has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Xudong Pan
School of Mechatronics Engineering, Harbin Institute of Technology, Harbin 150001, China
5 shared publications - Guo-Li Wang
School of Physics Harbin Institute of Technology 150001 Harbin China
3 shared publications - Yuxin Zhang
School of Mechatronics Engineering, Harbin Institute of Technology, Harbin 150001, China
2 shared publications Changyu Chen
Beijing Institute of Spacecraft Environment Engineering, Beijing, China
1 shared publication- Chengcheng Li
School of Mechatronics Engineering, Harbin Institute of Technology, Harbin, China
1 shared publication Fanwei Meng
Beijing Institute of Spacecraft Environment Engineering, Beijing, China
1 shared publication
Latest Publications
- 15 June 2026
- Published by Springer Nature in Intelligent Service Robotics
- Vol. 19 (4) , 69
Modeling and torque compensation control of double tendon–sheath artificial muscle with time-varying configuration
- 15 June 2026
- Published by Springer Nature in Intelligent Service Robotics
- Vol. 19 (4) , 69
Modeling and torque compensation control of double tendon–sheath artificial muscle with time-varying configuration
- Open Access
- 11 May 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (10) , 4743
High-Voltage Electrical Impulse Rock-Breaking Principle Prototype and Investigation of Electrical Parameters
Due to the complex geological conditions and the low ability to drill into deep strata, the current traditional mechanical methods in deep well drilling have the problems of low production efficiency and high working costs. Aiming at the problem of modularization of industrial applications of pulse generators in high-voltage electric pulse rock breaking technology, a high-voltage electric pulse rock breaking system based on the compound booster method is proposed in this study, and the miniaturization of high-voltage electric pulse rock breaking equipment is realized. A small pulse generator based on the compound booster method is designed. A set of high-voltage electric pulse rock-breaking experimental platforms is set up with a multistage BK booster circuit and a voltage-doubling circuit. Under the condition that the output discharge frequency is 5 Hz and the peak voltage is not less than 500 kV, the platform is used to carry out the fracturing experiment of ~3000 m Yingcheng formation rhyolite. COMSOL Multiphysics software was used to build a rock breakdown simulation model, and the rock-crushing process was revealed under the action of the high-voltage electrical pulse through simulation. The results show that the experimental platform can meet the requirements of the high-voltage electric pulse rock-breaking experiment, and the combined pressure booster method expands the design idea for the industrial application of high-voltage electric pulse drilling technology.
- 11 May 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (10) , 4743
Open AccessHigh-Voltage Electrical Impulse Rock-Breaking Principle Prototype and Investigation of Electrical Parameters
Due to the complex geological conditions and the low ability to drill into deep strata, the current traditional mechanical methods in deep well drilling have the problems of low production efficiency and high working costs. Aiming at the problem of modularization of industrial applications of pulse generators in high-voltage electric pulse rock breaking technology, a high-voltage electric pulse rock breaking system based on the compound booster method is proposed in this study, and the miniaturization of high-voltage electric pulse rock breaking equipment is realized. A small pulse generator based on the compound booster method is designed. A set of high-voltage electric pulse rock-breaking experimental platforms is set up with a multistage BK booster circuit and a voltage-doubling circuit. Under the condition that the output discharge frequency is 5 Hz and the peak voltage is not less than 500 kV, the platform is used to carry out the fracturing experiment of ~3000 m Yingcheng formation rhyolite. COMSOL Multiphysics software was used to build a rock breakdown simulation model, and the rock-crushing process was revealed under the action of the high-voltage electrical pulse through simulation. The results show that the experimental platform can meet the requirements of the high-voltage electric pulse rock-breaking experiment, and the combined pressure booster method expands the design idea for the industrial application of high-voltage electric pulse drilling technology.
- 1 August 2024
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 134 (1-2) , 969-985
Visual guidance method for artificial assembly in visual blind areas based on augmented reality
- 1 August 2024
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 134 (1-2) , 969-985
Visual guidance method for artificial assembly in visual blind areas based on augmented reality
- Open Access
High Voltage Electric Pulse Drilling: A Study of Variables through Simulation and Experimental Tests
With the deepening of drilling depth, the difficulty of drilling engineering increases gradually due to the complex geological conditions. The traditional mechanical drilling method shows the problems of high energy consumption, low efficiency, long cycle and high cost. Because of the characteristics of rock, the high abrasiveness of rock causes great wear to the bit, which becomes an important factor affecting the drilling rate. High voltage electric pulse (Abbreviated as HVEP later in this paper) drilling technology is a new technology developed in the past several decades. The technology uses plasma channel, water jet or shock wave generated by high voltage electric pulse discharge to break rock. It has the characteristics of environmental protection, directional breaking, easy control of rock breaking process and fast speed in the face of complex hard rock. In this paper, the mechanism and technology of rock breaking by high voltage electric pulse method in deep drilling are studied, and the functional test is carried out.
Open AccessHigh Voltage Electric Pulse Drilling: A Study of Variables through Simulation and Experimental Tests
With the deepening of drilling depth, the difficulty of drilling engineering increases gradually due to the complex geological conditions. The traditional mechanical drilling method shows the problems of high energy consumption, low efficiency, long cycle and high cost. Because of the characteristics of rock, the high abrasiveness of rock causes great wear to the bit, which becomes an important factor affecting the drilling rate. High voltage electric pulse (Abbreviated as HVEP later in this paper) drilling technology is a new technology developed in the past several decades. The technology uses plasma channel, water jet or shock wave generated by high voltage electric pulse discharge to break rock. It has the characteristics of environmental protection, directional breaking, easy control of rock breaking process and fast speed in the face of complex hard rock. In this paper, the mechanism and technology of rock breaking by high voltage electric pulse method in deep drilling are studied, and the functional test is carried out.
- Open Access
Meshing Stiffness Calculation of Disposable Harmonic Drive under Full Load
Mechanical equipment in the field of aerospace that is used only once is called disposable machinery. As a piece of typical disposable machinery, disposable harmonic gear exhibit stiffness failure with a large load. This manuscript distinguishes disposable harmonic gear from conventional harmonic gear in terms of the application environment and structure. Then, this paper determines the single-tooth stiffness of the disposable harmonic gear under full load by using the non-uniform beam model and the improved energy method. In addition, the multi-tooth meshing in the disposable harmonic drive is considered, and the improved energy method is modified. Besides, the normal contact force and comprehensive elastic displacement at each meshing position are calculated according to the finite element model. Additionally, curves of the single-tooth stiffness and the comprehensive meshing stiffness are obtained. The theoretical results of the modified analytical method and FEM are compared to verify the correctness of the proposed method in terms of calculating the meshing stiffness of the disposable harmonic drive. Finally, FEM is used to obtain the failure form of the disposable harmonic gear under overload.
Open AccessMeshing Stiffness Calculation of Disposable Harmonic Drive under Full Load
Mechanical equipment in the field of aerospace that is used only once is called disposable machinery. As a piece of typical disposable machinery, disposable harmonic gear exhibit stiffness failure with a large load. This manuscript distinguishes disposable harmonic gear from conventional harmonic gear in terms of the application environment and structure. Then, this paper determines the single-tooth stiffness of the disposable harmonic gear under full load by using the non-uniform beam model and the improved energy method. In addition, the multi-tooth meshing in the disposable harmonic drive is considered, and the improved energy method is modified. Besides, the normal contact force and comprehensive elastic displacement at each meshing position are calculated according to the finite element model. Additionally, curves of the single-tooth stiffness and the comprehensive meshing stiffness are obtained. The theoretical results of the modified analytical method and FEM are compared to verify the correctness of the proposed method in terms of calculating the meshing stiffness of the disposable harmonic drive. Finally, FEM is used to obtain the failure form of the disposable harmonic gear under overload.
- Open Access
Calculating the Load Distribution and Contact Stress of the Disposable Harmonic Drive under Full Load
Mechanical equipment that will not be reused is defined as disposable machinery. Disposable harmonic drives (HDs) are commonly used in the field of aerospace and are sensitive to payloads. Reasonable calculation of the gear strength is essential for structural design. A method of calculating the contact characteristics of HDs under full load by combining a surface contact model with a three-dimensional finite element model (FEM) is proposed in this work. The mathematical model was established for calculating the no-load backlash of conventional and disposable harmonic gears after assembly. Afterward, the tooth load distribution and surface contact stress were determined using the Hertz contact theory. Finally, ABAQUS software was used to establish the FEM of the disposable HD, and the results were compared with those obtained from the theoretical model. The results revealed that the disposable harmonic gear can realize short-term transmission under full load.
Open AccessCalculating the Load Distribution and Contact Stress of the Disposable Harmonic Drive under Full Load
Mechanical equipment that will not be reused is defined as disposable machinery. Disposable harmonic drives (HDs) are commonly used in the field of aerospace and are sensitive to payloads. Reasonable calculation of the gear strength is essential for structural design. A method of calculating the contact characteristics of HDs under full load by combining a surface contact model with a three-dimensional finite element model (FEM) is proposed in this work. The mathematical model was established for calculating the no-load backlash of conventional and disposable harmonic gears after assembly. Afterward, the tooth load distribution and surface contact stress were determined using the Hertz contact theory. Finally, ABAQUS software was used to establish the FEM of the disposable HD, and the results were compared with those obtained from the theoretical model. The results revealed that the disposable harmonic gear can realize short-term transmission under full load.
- 23 July 2020
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 109 (7-8) , 1929-1940
Spherical edge burr formation during servo valve spool shoulder grinding: identifying the formation mechanism and designing a deburring device
- 23 July 2020
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 109 (7-8) , 1929-1940
Spherical edge burr formation during servo valve spool shoulder grinding: identifying the formation mechanism and designing a deburring device
- 12 April 2017
- Published by Taylor & Francis in International Journal of Systems Science
- Vol. 48 (10) , 2091-2103
H∞ output tracking control of uncertain and disturbed nonlinear systems based on neural network model
The work presented in this paper seeks to address the tracking problem for uncertain continuous nonlinear systems with external disturbances. The objective is to obtain a model that uses a reference-based output feedback tracking control law. The control scheme is based on neural networks and a linear difference inclusion (LDI) model, and a PDC structure and H∞ performance criterion are used to attenuate external disturbances. The stability of the whole closed-loop model is investigated using the well-known quadratic Lyapunov function. The key principles of the proposed approach are as follows: neural networks are first used to approximate nonlinearities, to enable a nonlinear system to then be represented as a linearised LDI model. An LMI (linear matrix inequality) formula is obtained for uncertain and disturbed linear systems. This formula enables a solution to be obtained through an interior point optimisation method for some nonlinear output tracking control problems. Finally, simulations and comparisons are provided on two practical examples to illustrate the validity and effectiveness of the proposed method.
- 12 April 2017
- Published by Taylor & Francis in International Journal of Systems Science
- Vol. 48 (10) , 2091-2103
H∞ output tracking control of uncertain and disturbed nonlinear systems based on neural network model
The work presented in this paper seeks to address the tracking problem for uncertain continuous nonlinear systems with external disturbances. The objective is to obtain a model that uses a reference-based output feedback tracking control law. The control scheme is based on neural networks and a linear difference inclusion (LDI) model, and a PDC structure and H∞ performance criterion are used to attenuate external disturbances. The stability of the whole closed-loop model is investigated using the well-known quadratic Lyapunov function. The key principles of the proposed approach are as follows: neural networks are first used to approximate nonlinearities, to enable a nonlinear system to then be represented as a linearised LDI model. An LMI (linear matrix inequality) formula is obtained for uncertain and disturbed linear systems. This formula enables a solution to be obtained through an interior point optimisation method for some nonlinear output tracking control problems. Finally, simulations and comparisons are provided on two practical examples to illustrate the validity and effectiveness of the proposed method.