Asrin Piroutiniya
Research Subjects
Asrin Piroutiniya has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Mohamad Hosein Rasekhmanesh
Group of RadioFrequency: Circuits and Systems (RFCAS), Escuela Politécnica Superior, Universidad Autónoma de Madrid, 28049 Madrid, Spain
3 shared publications - Jorge Alfonso Ruiz-Cruz
Applied Electromagnetics Group, Information Processing and Telecommunications Center, E.T.S. de Ingenieros de Telecomunicacin, Universidad Politcnica de Madrid, Madrid, Spain
2 shared publications - Jose Luis Masa-Campos
Information Processing and Telecommunications Center (IPTC), ETSI Telecomunicacin, Universidad Politcnica de Madrid, Madrid, Spain
2 shared publications - Adrian Tamayo-Dominguez
Universidad Politécnica de Madrid
1 shared publication - Ashish Kumar
Department of Electronics technology, Opto-electronics and Laser Technology Group, Universidad Carlos III de Madrid, Madrid, Spain
1 shared publication - Daniel Gallego-Cabo
Leapwave Technology 2 , 28919 Leganés, Madrid
1 shared publication
Latest Publications
- Open Access
- 23 July 2026
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 140 (4)
Low-index and thin-film material characterization in the terahertz range via dielectric waveguide evanescent-field interaction
Terahertz (THz) and millimeter-wave (mmW) spectroscopy provide non-ionizing, label-free access to the electromagnetic response of a wide range of materials, enabling applications in quality control, biomedical diagnostics, and non-destructive evaluation. Conventional free-space THz spectroscopy, however, often suffers from limited interaction length and reduced sensitivity when the sample is thin, spatially localized, available only in small volume, or incompatible with beam-based fixtures. In this work, we present an integrated, non-contact approach for broadband material-property extraction based on the evanescent field of a low-loss high-resistivity silicon dielectric waveguide. The material under test (MUT) is placed in the cladding region, where it perturbs the guided-mode propagation constant and attenuation. By measuring the complex transmission through a reference waveguide and a waveguide loaded with the MUT and by combining these data with mode simulations and a perturbation-based inversion, we extract the complex permittivity over a continuous frequency band. The approach leverages an evanescent-field-based non-destructive method, a compact measurement setup, and feasibility to rescale toward higher frequencies for broadband material screening in the mmW to THz range.
- 23 July 2026
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 140 (4)
Open AccessLow-index and thin-film material characterization in the terahertz range via dielectric waveguide evanescent-field interaction
Terahertz (THz) and millimeter-wave (mmW) spectroscopy provide non-ionizing, label-free access to the electromagnetic response of a wide range of materials, enabling applications in quality control, biomedical diagnostics, and non-destructive evaluation. Conventional free-space THz spectroscopy, however, often suffers from limited interaction length and reduced sensitivity when the sample is thin, spatially localized, available only in small volume, or incompatible with beam-based fixtures. In this work, we present an integrated, non-contact approach for broadband material-property extraction based on the evanescent field of a low-loss high-resistivity silicon dielectric waveguide. The material under test (MUT) is placed in the cladding region, where it perturbs the guided-mode propagation constant and attenuation. By measuring the complex transmission through a reference waveguide and a waveguide loaded with the MUT and by combining these data with mode simulations and a perturbation-based inversion, we extract the complex permittivity over a continuous frequency band. The approach leverages an evanescent-field-based non-destructive method, a compact measurement setup, and feasibility to rescale toward higher frequencies for broadband material screening in the mmW to THz range.
- Open Access
Dual-Mode Conical Horn Antenna with 2-D Azimuthal Monopulse Pattern for Millimeter-Wave Applications
In this paper, a novel concept of a three-dimensional full metal system including a Dual-Mode Converter (DMC) network integrated with a high-gain Conical Horn Antenna (CHA) is presented. This system is designed for 5G millimeter wave applications requiring monopulse operation at K-band (). The DMC integrates two mode converters. They excite either the or the modes of the circular waveguide of the CHA. The input of the mode converters is the mode of two independent WR-28 standard rectangular waveguide ports. By integrating the DMC with the CHA, the whole system, called a Dual-Mode Conical Horn Antenna (DM-CHA), is formed, radiating the sum () and difference () patterns associated to the monopulse operation. To adequately prevent the propagation of higher order modes and mode mutual coupling, this integration procedure is carefully designed and fabricated. To prove the performance of the design, the DMC network was fabricated using subtractive manufacturing by Computer Numerical Control (CNC) technology. The CHA was fabricated using additive manufacturing by Direct Metal Laser Sintering (DLMS) technology. Finally, the simulation and measurement results were exhaustively compared, including return loss, isolation, radiation pattern, and gain of the full DM-CHA structure. It is noteworthy that this system provided up to per beam in the angular of arrival detection to support the high data rate operation for 5G satellite communications in the millimeter-wave band.Open AccessDual-Mode Conical Horn Antenna with 2-D Azimuthal Monopulse Pattern for Millimeter-Wave Applications
In this paper, a novel concept of a three-dimensional full metal system including a Dual-Mode Converter (DMC) network integrated with a high-gain Conical Horn Antenna (CHA) is presented. This system is designed for 5G millimeter wave applications requiring monopulse operation at K-band (). The DMC integrates two mode converters. They excite either the or the modes of the circular waveguide of the CHA. The input of the mode converters is the mode of two independent WR-28 standard rectangular waveguide ports. By integrating the DMC with the CHA, the whole system, called a Dual-Mode Conical Horn Antenna (DM-CHA), is formed, radiating the sum () and difference () patterns associated to the monopulse operation. To adequately prevent the propagation of higher order modes and mode mutual coupling, this integration procedure is carefully designed and fabricated. To prove the performance of the design, the DMC network was fabricated using subtractive manufacturing by Computer Numerical Control (CNC) technology. The CHA was fabricated using additive manufacturing by Direct Metal Laser Sintering (DLMS) technology. Finally, the simulation and measurement results were exhaustively compared, including return loss, isolation, radiation pattern, and gain of the full DM-CHA structure. It is noteworthy that this system provided up to per beam in the angular of arrival detection to support the high data rate operation for 5G satellite communications in the millimeter-wave band. - Open Access
Beam Steering 3D Printed Dielectric Lens Antennas for Millimeter-Wave and 5G Applications
Two types of cost-efficient antennas based on dielectric gradient index dielectric lens have been designed for 5G applications at . The first is a linearly polarized flat lens antenna (LP-FLA) for terrestrial 5G communications. The second is a novel circularly polarized stepped lens antenna (CP-SLA) for 5G satellite services. An efficient design method is presented to optimize and conform the lens topology to the radiation pattern coming from the antenna feeder. The LP-FLA is fed by a traditional linearly polarized pyramidal horn antenna (PHA). The CP-SLA is fed by an open-ended bow-tie waveguide cavity (BCA) antenna. This cavity feeder (BCA), using cross-sections with bow-tie shapes, allows having circular polarization at the desired frequency bandwidth. The two types of presented antennas have been manufactured in order to verify their performance by an easy, low-cost, three-dimensional (3D) printing technique based on stereolithography. The peak realized gain value for the flat (LP-FLA) and stepped (CP-SLA) lens antennas have been increased at to and , respectively, by disposing the lens structures at the appropriated distance from the feeders. Likewise, using an array of horns (PHA) or open-ended bow-tie waveguide cavity (BCA) antenna feeders, it is possible to obtain a maximum steering angle range of 20° and 35°, for a directivity over and , in the planar and stepped lens antennas, respectively.Open AccessBeam Steering 3D Printed Dielectric Lens Antennas for Millimeter-Wave and 5G Applications
Two types of cost-efficient antennas based on dielectric gradient index dielectric lens have been designed for 5G applications at . The first is a linearly polarized flat lens antenna (LP-FLA) for terrestrial 5G communications. The second is a novel circularly polarized stepped lens antenna (CP-SLA) for 5G satellite services. An efficient design method is presented to optimize and conform the lens topology to the radiation pattern coming from the antenna feeder. The LP-FLA is fed by a traditional linearly polarized pyramidal horn antenna (PHA). The CP-SLA is fed by an open-ended bow-tie waveguide cavity (BCA) antenna. This cavity feeder (BCA), using cross-sections with bow-tie shapes, allows having circular polarization at the desired frequency bandwidth. The two types of presented antennas have been manufactured in order to verify their performance by an easy, low-cost, three-dimensional (3D) printing technique based on stereolithography. The peak realized gain value for the flat (LP-FLA) and stepped (CP-SLA) lens antennas have been increased at to and , respectively, by disposing the lens structures at the appropriated distance from the feeders. Likewise, using an array of horns (PHA) or open-ended bow-tie waveguide cavity (BCA) antenna feeders, it is possible to obtain a maximum steering angle range of 20° and 35°, for a directivity over and , in the planar and stepped lens antennas, respectively.