Yanqing Duan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yanqing Duan has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Zhihong Liu
College of Environmental Science and Engineering, Taiyuan University of Technology, Taiyuan 030024, China
4 shared publications - Aijuan Zhou
Taiyuan University of Technology
3 shared publications - Wenzong Liu
Harbin Institute of Technology Shenzhen
2 shared publications - Xiuping Yue
College of Environmental Science and Engineering, Taiyuan University of Technology, Taiyuan, 030024, China
2 shared publications - Zhang-Wei He
Key Laboratory of Northwest Water Resource, Environment and Ecology, Ministry of Education, School of Environmental and Municipal Engineering, Xi'an University of Architecture and Technology, Xi'an 710055, China; Shaanxi Key Laboratory of Environmental Engineering, Xi'an University of Architecture and Technology, Xi'an 710055, China
2 shared publications - Haokun Wu
College of Environmental Science and Engineering, Taiyuan University of Technology, Taiyuan 030024, China
1 shared publication
Latest Publications
- Open Access
- 4 October 2026
- Published by MDPI AG in Fermentation
- Vol. 12 (10) , 470
3D-Printed Hierarchical Porous MgAl-Layered Double Hydroxide/Sodium Alginate Monoliths for Efficient Recovery of Volatile Fatty Acids from Anaerobic Fermentation Broth
Recovering volatile fatty acids (VFAs) from anaerobic fermentation broth as preferred carbon sources is often hindered by the poor recoverability of powdered adsorbents and the slow mass transfer within conventional hydrogel beads. Herein, we report a MgAl-layered double hydroxide (LDH) and sodium alginate (SA) composite ink tailored for extrusion-based 3D printing, followed by Ca2+ crosslinking and freeze-drying to fabricate monolithic adsorbents. Rheological tests show that the ink exhibits shear-thinning behavior and elastic-dominated viscoelasticity (G′ > G″), ensuring smooth extrusion and high shape fidelity during printing. Under optimized conditions (25 °C, 3.0 g/L, 120 min, pH 7.0), the 3D-printed monolith removed 55.74% of total VFAs. Kinetic analysis reveals that the adsorption follows the pseudo-second-order model (R2 = 0.915), consistent with a chemically controlled adsorption contribution and yielding a calculated equilibrium capacity of 286.5 mg/g. Notably, the adsorbent exhibits a pronounced selectivity toward acetic acid, which accounts for 62% of the total adsorbed VFAs. These findings demonstrate that 3D printing offers a viable strategy to overcome the intrinsic limitations of LDH-based adsorbents, namely, difficult separation and limited internal diffusion, thereby enabling efficient and selective VFA recovery from complex fermentation streams.
- 4 October 2026
- Published by MDPI AG in Fermentation
- Vol. 12 (10) , 470
Open Access3D-Printed Hierarchical Porous MgAl-Layered Double Hydroxide/Sodium Alginate Monoliths for Efficient Recovery of Volatile Fatty Acids from Anaerobic Fermentation Broth
Recovering volatile fatty acids (VFAs) from anaerobic fermentation broth as preferred carbon sources is often hindered by the poor recoverability of powdered adsorbents and the slow mass transfer within conventional hydrogel beads. Herein, we report a MgAl-layered double hydroxide (LDH) and sodium alginate (SA) composite ink tailored for extrusion-based 3D printing, followed by Ca2+ crosslinking and freeze-drying to fabricate monolithic adsorbents. Rheological tests show that the ink exhibits shear-thinning behavior and elastic-dominated viscoelasticity (G′ > G″), ensuring smooth extrusion and high shape fidelity during printing. Under optimized conditions (25 °C, 3.0 g/L, 120 min, pH 7.0), the 3D-printed monolith removed 55.74% of total VFAs. Kinetic analysis reveals that the adsorption follows the pseudo-second-order model (R2 = 0.915), consistent with a chemically controlled adsorption contribution and yielding a calculated equilibrium capacity of 286.5 mg/g. Notably, the adsorbent exhibits a pronounced selectivity toward acetic acid, which accounts for 62% of the total adsorbed VFAs. These findings demonstrate that 3D printing offers a viable strategy to overcome the intrinsic limitations of LDH-based adsorbents, namely, difficult separation and limited internal diffusion, thereby enabling efficient and selective VFA recovery from complex fermentation streams.
- Open Access
- 13 September 2024
- Published by MDPI AG in Fermentation
- Vol. 10 (9) , 476
Upgrading Denitrification by Optimal Adsorption of SCFAs from Sludge Alkaline Fermentation Liquid by Acid-Modified Sepiolite
Sludge alkaline fermentation liquid (AFL) is a potential carbon source for biological denitrification. However, its effectiveness is limited due to the presence of nutrients and heavy metals. In this study, acid-modified sepiolite (MSEP) was used to extract short-chain fatty acids (SCFAs) from AFL under optimized conditions and then with the prepared MSEP-AFL as a carbon source for denitrification. The optimal condition with an MSEP dosage of 1.96 g/L and pH 7.93 at 30 °C was obtained based on single-factor experiments and response surface methodology (RSM). Carbon balance revealed that 96.2% of the SCFAs, including 43.7% acetate and 23.5% propionic acid, was retained in the MSEP, demonstrating its high selectivity. The adsorption process followed the pseudo-second-order kinetic and Langmuir isothermal model, indicating dominant physical adsorption on the surface or in the fiber pores. This was further supported by the changes in the morphological features and surface properties of the MSEP. In the batch nitrate utilization experiments, the prepared MSEP-AFL was proven to be efficient as a carbon source, with a nitrate removal efficiency of 88.7% and a specific denitrification rate of 8.2 mg NOx-N/g VSS·h, which was 22% higher than that of the AFL. This was due to the establishment of a delicate “release–utilization” balance. These findings contribute to our understanding of the use of AFL for denitrification.
- 13 September 2024
- Published by MDPI AG in Fermentation
- Vol. 10 (9) , 476
Open AccessUpgrading Denitrification by Optimal Adsorption of SCFAs from Sludge Alkaline Fermentation Liquid by Acid-Modified Sepiolite
Sludge alkaline fermentation liquid (AFL) is a potential carbon source for biological denitrification. However, its effectiveness is limited due to the presence of nutrients and heavy metals. In this study, acid-modified sepiolite (MSEP) was used to extract short-chain fatty acids (SCFAs) from AFL under optimized conditions and then with the prepared MSEP-AFL as a carbon source for denitrification. The optimal condition with an MSEP dosage of 1.96 g/L and pH 7.93 at 30 °C was obtained based on single-factor experiments and response surface methodology (RSM). Carbon balance revealed that 96.2% of the SCFAs, including 43.7% acetate and 23.5% propionic acid, was retained in the MSEP, demonstrating its high selectivity. The adsorption process followed the pseudo-second-order kinetic and Langmuir isothermal model, indicating dominant physical adsorption on the surface or in the fiber pores. This was further supported by the changes in the morphological features and surface properties of the MSEP. In the batch nitrate utilization experiments, the prepared MSEP-AFL was proven to be efficient as a carbon source, with a nitrate removal efficiency of 88.7% and a specific denitrification rate of 8.2 mg NOx-N/g VSS·h, which was 22% higher than that of the AFL. This was due to the establishment of a delicate “release–utilization” balance. These findings contribute to our understanding of the use of AFL for denitrification.
- Open Access
- 3 May 2024
- Published by MDPI AG in Fermentation
- Vol. 10 (5) , 243
Syntrophic Jiont of Sulfate-Reducing Bacteria and Hydrogen-Producing Acetogen Stimulated Methane Production from Waste Activated Sludge Digestion
Anaerobic digestion of waste-activated sludge (WAS) towards biogas recovery is constrained by the limited hydrolysis and inhibited acetogenesis steps that hinder subsequent energy recovery. This study employed Fe(VI)/S(IV) oxidation to enhance the WAS solubilization and coupled it with the syntrophic interaction of hydrogen-producing acetogen (HPA) and sulfate-reducing bacteria (SRB) to stimulate the successive procedure towards methane production. Results showed that the dosage ratio of HPA-SRB to WAS (H-S-W) with 1:1:50 outperformed with the highest methane production potential (11.63 ± 1.87 mL CH4/(g VSS·d). Meanwhile, the efficient and sequential process from acetogenesis to methanogenesis stimulated by HPA-SRB was evidenced by a significant decrease of 30.2% in the acetate concentration. The microbial community structure further manifested the crucial role of HPA-SRB with increased abundance of Desulfobulbus (2.07%), Syntrophomonas (1.24%) and Smithella (1.63%), which stimulated acetophilic methanogen boost with Methanobacterium dominating with 77.51% in H-S-W100. Furthermore, the positive syntrophic relationships among HPA-SRB and acetophilic methanogens towards methane production were confirmed via molecular ecological network and canonical correspondence analysis. This study highlighted the syntrophic cooperation of the mixed consortia of HPA and SRB on methane production based on Fe(VI)/S(IV) pretreatment and provided the theoretical and technical basis for the potential implementation of novel methanogenesis technology for WAS treatment.
- 3 May 2024
- Published by MDPI AG in Fermentation
- Vol. 10 (5) , 243
Open AccessSyntrophic Jiont of Sulfate-Reducing Bacteria and Hydrogen-Producing Acetogen Stimulated Methane Production from Waste Activated Sludge Digestion
Anaerobic digestion of waste-activated sludge (WAS) towards biogas recovery is constrained by the limited hydrolysis and inhibited acetogenesis steps that hinder subsequent energy recovery. This study employed Fe(VI)/S(IV) oxidation to enhance the WAS solubilization and coupled it with the syntrophic interaction of hydrogen-producing acetogen (HPA) and sulfate-reducing bacteria (SRB) to stimulate the successive procedure towards methane production. Results showed that the dosage ratio of HPA-SRB to WAS (H-S-W) with 1:1:50 outperformed with the highest methane production potential (11.63 ± 1.87 mL CH4/(g VSS·d). Meanwhile, the efficient and sequential process from acetogenesis to methanogenesis stimulated by HPA-SRB was evidenced by a significant decrease of 30.2% in the acetate concentration. The microbial community structure further manifested the crucial role of HPA-SRB with increased abundance of Desulfobulbus (2.07%), Syntrophomonas (1.24%) and Smithella (1.63%), which stimulated acetophilic methanogen boost with Methanobacterium dominating with 77.51% in H-S-W100. Furthermore, the positive syntrophic relationships among HPA-SRB and acetophilic methanogens towards methane production were confirmed via molecular ecological network and canonical correspondence analysis. This study highlighted the syntrophic cooperation of the mixed consortia of HPA and SRB on methane production based on Fe(VI)/S(IV) pretreatment and provided the theoretical and technical basis for the potential implementation of novel methanogenesis technology for WAS treatment.
- 12 September 2023
- Published by Elsevier in Journal of Environmental Management
- Vol. 346, 118967
Tailored short-chain fatty acids conversion from waste activated sludge fermentation via persulfate oxidation and C3–C5 io-SRB metabolizers
- 12 September 2023
- Published by Elsevier in Journal of Environmental Management
- Vol. 346, 118967
Tailored short-chain fatty acids conversion from waste activated sludge fermentation via persulfate oxidation and C3–C5 io-SRB metabolizers