Xiyu Gu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Xiyu Gu has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
- Chengliang Sun
School of Integrated Circuits Hubei Key Laboratory of Electronic Manufacturing and Packaging Integration Wuhan University Wuhan China
9 shared publications - Yan Liu
School of Microelectronics, Wuhan Textile University, Wuhan, China
9 shared publications - Yao Cai
School of Integrated Circuits Hubei Key Laboratory of Electronic Manufacturing and Packaging Integration Wuhan University Wuhan China
8 shared publications - Yuanhang Qu
Institute of Technological Sciences, Wuhan University, Wuhan, China
7 shared publications - Zhiwei Wen
The Institute of Technological Sciences, Wuhan University, Wuhan 430072, China
5 shared publications - Shengxiang Wang
Wuhan Textile University
4 shared publications
Latest Publications
- 27 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (3) , 1579-1584
Temperature-Decoupled Multimodal Surface Acoustic Wave Strain Sensors Using Z-Cut Lithium Niobate on Insulator Substrate
Surface acoustic wave (SAW) strain sensors have attracted widespread attention in recent years due to their wireless, passive operation and excellent stability in complex environments. In this work, a multimodal SAW strain sensor based on Z-cut lithium niobate on insulator (LNOI) substrate is proposed and fabricated. Five distinct acoustic modes are identified, each exhibiting significantly different responses to strain and temperature. Among them, the 0th-order antisymmetric Rayleigh mode shows the highest positive strain sensitivity (92 Hz/ $\mu \varepsilon $ ), while the 1st-order symmetric Rayleigh mode exhibits a negative strain sensitivity (−64 Hz/ $\mu \varepsilon $ ). To eliminate the interference of temperature in strain measurements, an effective decoupling method is proposed based on the sensitivity differences of these two modes, using a frequency response sensitivity matrix to achieve the separation of temperature and strain signals. Experimental results demonstrate excellent decoupling performance, with root-mean-square errors of $0.13~^{\circ }$ C for temperature and $15.88~\mu \varepsilon $ for strain. These findings confirm the great potential of the proposed sensor for high-performance, wireless, and multiparameter sensing applications.
- 27 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (3) , 1579-1584
Temperature-Decoupled Multimodal Surface Acoustic Wave Strain Sensors Using Z-Cut Lithium Niobate on Insulator Substrate
Surface acoustic wave (SAW) strain sensors have attracted widespread attention in recent years due to their wireless, passive operation and excellent stability in complex environments. In this work, a multimodal SAW strain sensor based on Z-cut lithium niobate on insulator (LNOI) substrate is proposed and fabricated. Five distinct acoustic modes are identified, each exhibiting significantly different responses to strain and temperature. Among them, the 0th-order antisymmetric Rayleigh mode shows the highest positive strain sensitivity (92 Hz/ $\mu \varepsilon $ ), while the 1st-order symmetric Rayleigh mode exhibits a negative strain sensitivity (−64 Hz/ $\mu \varepsilon $ ). To eliminate the interference of temperature in strain measurements, an effective decoupling method is proposed based on the sensitivity differences of these two modes, using a frequency response sensitivity matrix to achieve the separation of temperature and strain signals. Experimental results demonstrate excellent decoupling performance, with root-mean-square errors of $0.13~^{\circ }$ C for temperature and $15.88~\mu \varepsilon $ for strain. These findings confirm the great potential of the proposed sensor for high-performance, wireless, and multiparameter sensing applications.
- 26 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (21) , 39773-39781
An H-Shaped Piezoelectric MEMS Dual-Axis Accelerometer
This paper focuses on the study of a piezoelectric dual-axis accelerometer using AlN/ScAlN double-layer piezoelectric films. The proposed accelerometer adopts SOI wafer as the substrate and constructs the AlN/ScAlN/Mo stack as the sensing layer. Through the establishment of theoretical model and finite element simulation, the relationship between the deformation of the structure and the output voltage of the port was analyzed and obtained. The first-order resonant frequencies of the designed accelerometer in the X and Y directions are 157.48 kHz and 83.28 kHz respectively. In addition, the experimental test results indicate that under the acceleration excitation at 500 Hz, the voltage sensitivities of the accelerometer in the X and Y directions are 1.19 mV/g and 1.81 mV/g respectively, and the minimum detectable signals in the X and Y directions are 7 mg and 6 mg respectively. The manufactured accelerometer has good linearity (0.9984) within the acceleration range of 0.2-2.4 g. The innovative structure proposed in this paper provides a new design idea for the research of piezoelectric accelerometers and is expected to promote the further development of this field.
- 26 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (21) , 39773-39781
An H-Shaped Piezoelectric MEMS Dual-Axis Accelerometer
This paper focuses on the study of a piezoelectric dual-axis accelerometer using AlN/ScAlN double-layer piezoelectric films. The proposed accelerometer adopts SOI wafer as the substrate and constructs the AlN/ScAlN/Mo stack as the sensing layer. Through the establishment of theoretical model and finite element simulation, the relationship between the deformation of the structure and the output voltage of the port was analyzed and obtained. The first-order resonant frequencies of the designed accelerometer in the X and Y directions are 157.48 kHz and 83.28 kHz respectively. In addition, the experimental test results indicate that under the acceleration excitation at 500 Hz, the voltage sensitivities of the accelerometer in the X and Y directions are 1.19 mV/g and 1.81 mV/g respectively, and the minimum detectable signals in the X and Y directions are 7 mg and 6 mg respectively. The manufactured accelerometer has good linearity (0.9984) within the acceleration range of 0.2-2.4 g. The innovative structure proposed in this paper provides a new design idea for the research of piezoelectric accelerometers and is expected to promote the further development of this field.
- 28 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 35 (9) , 1424-1427
Surface Acoustic Wave Resonator With Epitaxial ε-Ga2O3 Thin Films: Performance Characteristics and Temperature Sensor Potential
This letter presents a surface acoustic wave (SAW) resonator based on $\varepsilon $ -Ga2O3 thin films deposited via metal-organic chemical vapor deposition (MOCVD). Ti/Au interdigital transducers (IDTs), with an approximate finger width of $1.8~\mu $ m, were fabricated on the $\varepsilon $ -Ga2O3 thin film to create this SAW resonator. The SAW resonator’s series resonant frequency ( $f_{s}$ ) and parallel resonant frequency ( $f_{p}$ ) were found to be 673.5 and 673.8 MHz, respectively. Additionally, the device’s modified Butterworth-Van Dyke (MBVD) model was successfully constructed, and the elastic coefficients, piezoelectric coefficients, and dielectric constants of $\varepsilon $ -Ga2O3 material were obtained through first-principles calculations, forming the basis for a finite element simulation model. Finite element simulations revealed that at $f_{s}$ , the device exhibits Rayleigh mode. Finally, the device demonstrated a high quality factor ( $Q =3927$ ) and a high temperature coefficient of frequency [(TCF) = -56.73 ppm/K]. These findings reveal the potential application of $\varepsilon $ -Ga2O3 acoustic devices in temperature sensing.
- 28 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 35 (9) , 1424-1427
Surface Acoustic Wave Resonator With Epitaxial ε-Ga2O3 Thin Films: Performance Characteristics and Temperature Sensor Potential
This letter presents a surface acoustic wave (SAW) resonator based on $\varepsilon $ -Ga2O3 thin films deposited via metal-organic chemical vapor deposition (MOCVD). Ti/Au interdigital transducers (IDTs), with an approximate finger width of $1.8~\mu $ m, were fabricated on the $\varepsilon $ -Ga2O3 thin film to create this SAW resonator. The SAW resonator’s series resonant frequency ( $f_{s}$ ) and parallel resonant frequency ( $f_{p}$ ) were found to be 673.5 and 673.8 MHz, respectively. Additionally, the device’s modified Butterworth-Van Dyke (MBVD) model was successfully constructed, and the elastic coefficients, piezoelectric coefficients, and dielectric constants of $\varepsilon $ -Ga2O3 material were obtained through first-principles calculations, forming the basis for a finite element simulation model. Finite element simulations revealed that at $f_{s}$ , the device exhibits Rayleigh mode. Finally, the device demonstrated a high quality factor ( $Q =3927$ ) and a high temperature coefficient of frequency [(TCF) = -56.73 ppm/K]. These findings reveal the potential application of $\varepsilon $ -Ga2O3 acoustic devices in temperature sensing.
- 3 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (6) , 9600-9607
Design and Performance Analysis of a Multigrooved Cantilever-Type Piezoelectric Accelerometer
How to improve the sensitivity of Micro-electromechanical systems (MEMS) piezoelectric accelerometers has become a key technical problem in consumer electronics. In this paper, a multigrooved cantilever-type piezoelectric accelerometer based on composite film is manufactured to obtain high sensitivity of 4.62 mV/g, excessing typical accelerometer (3.36 mV/g). The theoretical model and finite element model are established to analyze the relationship between cantilever stiffness, stress distribution and sensitivity. The proposed accelerometers are fabricated by MEMS processes to form Mo/AlN/ScAlN/Mo piezoelectric stacks as the sensing layer. The experimental results show that the sensitivity, linearity, minimum detectable signal (MDS), and resonant frequency of the proposed piezoelectric accelerometer with multiple grooves are 4.62 mV/g, 0.99964, 0.02 g, and 15320 Hz, respectively. This new structure can provide inspiration for the design of high-sensitivity and high-linear MEMS piezoelectric accelerometers.
- 3 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (6) , 9600-9607
Design and Performance Analysis of a Multigrooved Cantilever-Type Piezoelectric Accelerometer
How to improve the sensitivity of Micro-electromechanical systems (MEMS) piezoelectric accelerometers has become a key technical problem in consumer electronics. In this paper, a multigrooved cantilever-type piezoelectric accelerometer based on composite film is manufactured to obtain high sensitivity of 4.62 mV/g, excessing typical accelerometer (3.36 mV/g). The theoretical model and finite element model are established to analyze the relationship between cantilever stiffness, stress distribution and sensitivity. The proposed accelerometers are fabricated by MEMS processes to form Mo/AlN/ScAlN/Mo piezoelectric stacks as the sensing layer. The experimental results show that the sensitivity, linearity, minimum detectable signal (MDS), and resonant frequency of the proposed piezoelectric accelerometer with multiple grooves are 4.62 mV/g, 0.99964, 0.02 g, and 15320 Hz, respectively. This new structure can provide inspiration for the design of high-sensitivity and high-linear MEMS piezoelectric accelerometers.
- 12 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (1) , 1323-1330
A Robust Thin-Film Encapsulation for RF-MEMS With Aluminum Nitride/Molybdenum Cap
Wafer-level thin-film packaging offers high yield, low cost and small packaging size and can be easily integrated into components within microelectromechanical systems (MEMS). In this work, a fabrication process of thin-film encapsulation (TFE) with aluminum nitride/molybdenum cap is proposed for the packaging of film bulk acoustic wave resonators and filters. The high Young’s modulus of aluminum nitride and the high toughness of molybdenum fully guarantee the stability of the packaging structure. By optimizing the sputtering parameters, aluminum nitride exhibits compressive stress, which compensates the tensile stress of molybdenum, resulting in an average stress distribution of 5.763MPa in the capping layer, thereby avoiding the bending of the packaging structure. Besides polyimide (HD8820) was spin-coated onto the capping layer to further improve the airtightness of the packaging. At the same time, network signal tests were conducted on the devices at every step of the packaging process to ensure that the packaging structure had minimal impact on device performance. Finally, the devices underwent the unbiased highly accelerated stress test (JESD22-A118B), resulting in only 0.2dB of loss. This method may hold immense commercial value in enhancing the performance of radio-frequency MEMS devices.
- 12 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (1) , 1323-1330
A Robust Thin-Film Encapsulation for RF-MEMS With Aluminum Nitride/Molybdenum Cap
Wafer-level thin-film packaging offers high yield, low cost and small packaging size and can be easily integrated into components within microelectromechanical systems (MEMS). In this work, a fabrication process of thin-film encapsulation (TFE) with aluminum nitride/molybdenum cap is proposed for the packaging of film bulk acoustic wave resonators and filters. The high Young’s modulus of aluminum nitride and the high toughness of molybdenum fully guarantee the stability of the packaging structure. By optimizing the sputtering parameters, aluminum nitride exhibits compressive stress, which compensates the tensile stress of molybdenum, resulting in an average stress distribution of 5.763MPa in the capping layer, thereby avoiding the bending of the packaging structure. Besides polyimide (HD8820) was spin-coated onto the capping layer to further improve the airtightness of the packaging. At the same time, network signal tests were conducted on the devices at every step of the packaging process to ensure that the packaging structure had minimal impact on device performance. Finally, the devices underwent the unbiased highly accelerated stress test (JESD22-A118B), resulting in only 0.2dB of loss. This method may hold immense commercial value in enhancing the performance of radio-frequency MEMS devices.
- 1 January 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 124 (1)
Advanced technologies of FBAR for tuning effective electromechanical coupling coefficient
The film bulk acoustic wave resonator (FBAR) is one of the most popular devices in the radio frequency field. Numerous researchers are simultaneously working to develop an effective electromechanical coupling coefficient (keff2) tuning technology, aiming to meet the diverse bandwidth requirements of the 5 G era. Based on a traditional FBAR process, this work prepares several different devices and then analyzes the four factors that influence keff2 from the perspective of process, material, and design. The pillar structure achieves the largest keff2 tuning range of 2.84% (33 MHz). The composite piezoelectric film can tune the overall resonant frequency in a wide range, and its keff2 tuning range is 1.75% (12.5 MHz). The area effect tunes the fs in a small range, ultimately achieving a keff2 tuning range of 1.16% (11 MHz). Film stress regulation achieves keff2 tuning range of 2.73% (30 MHz), but it has the greatest difficulty. The integration of various keff2 tunable methods has important guiding significance for the design of FBAR filters in the future.
- 1 January 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 124 (1)
Advanced technologies of FBAR for tuning effective electromechanical coupling coefficient
The film bulk acoustic wave resonator (FBAR) is one of the most popular devices in the radio frequency field. Numerous researchers are simultaneously working to develop an effective electromechanical coupling coefficient (keff2) tuning technology, aiming to meet the diverse bandwidth requirements of the 5 G era. Based on a traditional FBAR process, this work prepares several different devices and then analyzes the four factors that influence keff2 from the perspective of process, material, and design. The pillar structure achieves the largest keff2 tuning range of 2.84% (33 MHz). The composite piezoelectric film can tune the overall resonant frequency in a wide range, and its keff2 tuning range is 1.75% (12.5 MHz). The area effect tunes the fs in a small range, ultimately achieving a keff2 tuning range of 1.16% (11 MHz). Film stress regulation achieves keff2 tuning range of 2.73% (30 MHz), but it has the greatest difficulty. The integration of various keff2 tunable methods has important guiding significance for the design of FBAR filters in the future.
- Open Access
- 28 August 2023
- Published by AIP Publishing in Applied Physics Letters
- Vol. 123 (9)
A laterally excited bulk acoustic resonator with scattering vias in electrodes
Laterally excited bulk acoustic resonators (XBARs) using interdigital electrodes are currently limited in potential 5G applications due to the accompanied spurious modes and small capacitance. This Letter presents an XBAR with scattering vias in electrodes, named SV-BAR. The non-parallel boundaries thoroughly disrupt the coherent formation of standing waves in the lateral direction, thereby suppressing the higher-order spurious modes. The duty factor of SV-BAR is optimized as 0.5 using COMSOL Multiphysics finite element analysis for the 50 Ω impedance matching. The SV-BAR is fabricated using a 390 nm Z-cut LiNbO3 on an insulator substrate and exhibits an impressive ratio of Zp/Zs near 64.5 dB, a Kt2 of 21.80% at 4.762 GHz, as well as a large value f · Bode_Qmax · Kt2 (3.43 × 1011). The measured temperature coefficient of frequency is −69.8 ppm/°C, which can be compensated using SiO2 thin films. The SV-BAR provides an effective solution for high-performance radio frequency filters for 5G communication.
- 28 August 2023
- Published by AIP Publishing in Applied Physics Letters
- Vol. 123 (9)
Open AccessA laterally excited bulk acoustic resonator with scattering vias in electrodes
Laterally excited bulk acoustic resonators (XBARs) using interdigital electrodes are currently limited in potential 5G applications due to the accompanied spurious modes and small capacitance. This Letter presents an XBAR with scattering vias in electrodes, named SV-BAR. The non-parallel boundaries thoroughly disrupt the coherent formation of standing waves in the lateral direction, thereby suppressing the higher-order spurious modes. The duty factor of SV-BAR is optimized as 0.5 using COMSOL Multiphysics finite element analysis for the 50 Ω impedance matching. The SV-BAR is fabricated using a 390 nm Z-cut LiNbO3 on an insulator substrate and exhibits an impressive ratio of Zp/Zs near 64.5 dB, a Kt2 of 21.80% at 4.762 GHz, as well as a large value f · Bode_Qmax · Kt2 (3.43 × 1011). The measured temperature coefficient of frequency is −69.8 ppm/°C, which can be compensated using SiO2 thin films. The SV-BAR provides an effective solution for high-performance radio frequency filters for 5G communication.
- 13 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 44 (8) , 1344-1347
Study of High-Q Laterally Excited Bulk Wave Resonator With Smaller Gap-Width Reflectors
How to improve the quality factor (Q) of transversely excited bulk wave resonators (XBARs) has become a key technical problem in the RF field. In this study, a XBAR with 2 μm gap-width reflector based on LiNbO 3 was fabricated to attain Qp value of 1211, exceeding the measurement in typical XABR ( Qp = 372). Simulation results indicate that the capacity of reflector gap width to inhibit the propagation of longitudinal wave energy increases first and then decreases as gap width increases from 0.5 μm to 8 μm The measurement results obtained from XBAR with 2 μm gap-width reflectors and XBAR with 4 μm gap-width reflectors ( Qp = 802) demonstrate excellent consistency with the simulation results. This study presents the XBAR with largest Qp × K 2 eff (237.4) currently, which highlights the significant potential of utilizing smaller gap-width reflectors in XBARs to construct filters with large bandwidth and high frequency.
- 13 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 44 (8) , 1344-1347
Study of High-Q Laterally Excited Bulk Wave Resonator With Smaller Gap-Width Reflectors
How to improve the quality factor (Q) of transversely excited bulk wave resonators (XBARs) has become a key technical problem in the RF field. In this study, a XBAR with 2 μm gap-width reflector based on LiNbO 3 was fabricated to attain Qp value of 1211, exceeding the measurement in typical XABR ( Qp = 372). Simulation results indicate that the capacity of reflector gap width to inhibit the propagation of longitudinal wave energy increases first and then decreases as gap width increases from 0.5 μm to 8 μm The measurement results obtained from XBAR with 2 μm gap-width reflectors and XBAR with 4 μm gap-width reflectors ( Qp = 802) demonstrate excellent consistency with the simulation results. This study presents the XBAR with largest Qp × K 2 eff (237.4) currently, which highlights the significant potential of utilizing smaller gap-width reflectors in XBARs to construct filters with large bandwidth and high frequency.
- 14 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 136-139
A Tunable Dual-mode Lamb Wave Resonator with Floating Electrodes
In this paper, we present a tunable dual-mode Lamb wave resonator (LWR) based on Aluminum nitride thin films. The dual-mode LWR consists of floating electrodes positioned between interdigital electrodes (IDTs), which results in two resonant peaks, operating at 1.69GHz and 1.757 GHz when the height (H) of floating electrodes is $0.05 \mu \mathrm{m}$ and the width W is $0.7 \mu \mathrm{m}$, respectively. The resonant frequency and impedance ratio of the two peaks are tuned by the size of the floating electrodes. When the H is from $0.05 \mu \mathrm{m}$ to 0.25 $\mu \mathrm{m}$ and the W is $0.7 \mu \mathrm{m}$, the distance between the two peaks $(\Delta f)$ is adjusted from 67MHz to 455MHz. Furthermore, as W increases, the impedance ratio of the first peak is amplified while the second peak is attenuated. The coupling strength of the two peaks is close to that of conventional single-peak resonators. The tunable LWR with optimized floating electrodes shows great potential in fabricating high-frequency dual-passband filters.- 14 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 136-139
A Tunable Dual-mode Lamb Wave Resonator with Floating Electrodes
In this paper, we present a tunable dual-mode Lamb wave resonator (LWR) based on Aluminum nitride thin films. The dual-mode LWR consists of floating electrodes positioned between interdigital electrodes (IDTs), which results in two resonant peaks, operating at 1.69GHz and 1.757 GHz when the height (H) of floating electrodes is $0.05 \mu \mathrm{m}$ and the width W is $0.7 \mu \mathrm{m}$, respectively. The resonant frequency and impedance ratio of the two peaks are tuned by the size of the floating electrodes. When the H is from $0.05 \mu \mathrm{m}$ to 0.25 $\mu \mathrm{m}$ and the W is $0.7 \mu \mathrm{m}$, the distance between the two peaks $(\Delta f)$ is adjusted from 67MHz to 455MHz. Furthermore, as W increases, the impedance ratio of the first peak is amplified while the second peak is attenuated. The coupling strength of the two peaks is close to that of conventional single-peak resonators. The tunable LWR with optimized floating electrodes shows great potential in fabricating high-frequency dual-passband filters.