Ana Isabel Serrano-Esteban
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Ana Isabel Serrano-Esteban has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Cinthia Rodríguez
Department of Dentistry, Universidad Federico Henriquez y Carvajal, Santo Domingo 10106, Dominican Republic
1 shared publication - Estefanía Requena-Gómez
Faculty of Dentistry, Catholic University of Valencia Saint Vicent Martyr, 46001 Valencia, Spain
1 shared publication - Jesús Mena-Álvarez
Departments of Conservative Dentistry and Prosthetics, Faculty of Dentistry, Complutense University of Madrid
1 shared publication - Juan Manuel Aragoneses
Department of Dental Research in Universidad Federico Henríquez y Carvajal (UFHEC), Santo Domingo 10107, Dominican Republic
1 shared publication - María Bufalá Pérez
Department of Implant Surgery, Faculty of Health Sciences, Alfonso X el Sabio University, 28691 Madrid, Spain
1 shared publication
Latest Publications
- Open Access
- 14 February 2023
- Published by MDPI AG in Journal of Functional Biomaterials
- Vol. 14 (2) , 107
Cadaveric Identification through Macroscopic Analysis of Dental Implants Subjected to High Temperatures—An Experimental Model
The aim of this study was to determine the possibility of identifying a dental implant through the measurement of the apical width and the interspiral distance in a periapical radiograph after being subjected to high temperatures for certain lengths of time. In total, 11 fresh human anatomical models were selected, in which 137 implants were placed. Previous periapical radiographs were performed using parallelizers in each implant. Subsequently, the anatomical models were introduced into a crematory oven at different temperatures and for various durations: 500 °C/15 min, 500 °C/30 min, 700 °C/15 min, 800 °C/15 min, 800 °C/45 min, 500 °C/15 min, 700 °C/15 min, and finally, 1000 °C/120 min. After this, X-rays were taken via a parallel technique, and the apical width and interspiral distance were measured. The implants were disinserted, and the coronal width was used to calculate magnification or possible distortion. All data were analyzed by the Mann–Whitney U test. There were no statistically significant differences for the apical width parameter, except when the temperature was raised to 700 °C/15 min and to 800 °C/45 min. For the interspiral distance parameter, there were no statistically significant differences, except when the implants were subjected to 800 °C/15 min and 1000 °C/120 min. It was determined that there were changes in some groups based on the increase in temperature and exposure time. Neither of the two parameters were completely useful for the identification because some of the groups studied in both variables presented differences, which makes them difficult to identify correctly.
- 14 February 2023
- Published by MDPI AG in Journal of Functional Biomaterials
- Vol. 14 (2) , 107
Open AccessCadaveric Identification through Macroscopic Analysis of Dental Implants Subjected to High Temperatures—An Experimental Model
The aim of this study was to determine the possibility of identifying a dental implant through the measurement of the apical width and the interspiral distance in a periapical radiograph after being subjected to high temperatures for certain lengths of time. In total, 11 fresh human anatomical models were selected, in which 137 implants were placed. Previous periapical radiographs were performed using parallelizers in each implant. Subsequently, the anatomical models were introduced into a crematory oven at different temperatures and for various durations: 500 °C/15 min, 500 °C/30 min, 700 °C/15 min, 800 °C/15 min, 800 °C/45 min, 500 °C/15 min, 700 °C/15 min, and finally, 1000 °C/120 min. After this, X-rays were taken via a parallel technique, and the apical width and interspiral distance were measured. The implants were disinserted, and the coronal width was used to calculate magnification or possible distortion. All data were analyzed by the Mann–Whitney U test. There were no statistically significant differences for the apical width parameter, except when the temperature was raised to 700 °C/15 min and to 800 °C/45 min. For the interspiral distance parameter, there were no statistically significant differences, except when the implants were subjected to 800 °C/15 min and 1000 °C/120 min. It was determined that there were changes in some groups based on the increase in temperature and exposure time. Neither of the two parameters were completely useful for the identification because some of the groups studied in both variables presented differences, which makes them difficult to identify correctly.