Massimo Cavalera
Research Subjects
Massimo Cavalera has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Florian Zikeli
Civil and Environmental Engineering Department, UdR INSTM, University of Perugia, 05100 Terni, Italy
1 shared publication - Manuela Romagnoli
Department of Innovation in Biological, Agro-Food and Forest Systems (DIBAF), University of Tuscia, 01100 Viterbo, Italy
1 shared publication - Miha Humar
University of Ljubljana
1 shared publication - Sara Bergamasco
Department for innovation in biological, agro-food and forest systems (DIBAF), University of Tuscia, Via San Camillo de Lellis snc, 01100 Viterbo, Italy
1 shared publication - Swati Tamantini
Department of Innovation in Biological, Agro-Food and Forest Systems (DIBAF), University of Tuscia, 01100 Viterbo, Italy
1 shared publication
Latest Publications
- Open Access
- 21 January 2023
- Published by MDPI AG in Nanomaterials
- Vol. 13 (3) , 442
Cellulose Nano Crystals (CNC) as Additive for a Bio-Based Waterborne Acrylic Wood Coating: Decay, Artificial Weathering, Physical and Chemical Tests
Wood coatings prolong the service life of wood-based products, but they are usually of synthetic origin. The aim of the present article is to reduce the fossil-based compounds in a commercial waterborne acrylic coating by CNC addition and to test its performance. The coatings were applied on European beech and Norway spruce wood in order to test durability against Gloeophyllum trabeum (brown wood rot) and Trametes versicolor (white wood rot). Artificial weathering and blue stain, contact angle, physical tests (adhesion, impact and scratch test), chemical (FTIR) and morpho-anatomical analysis (SEM) were carried out. CNC addition increased viscosity, limiting the spreading of the coating into wood pores as visible after SEM observation, which reduced coating adhesion on the substrate. CNC improved fungal resistance as seen by a reduced mass loss and FTIR spectroscopy thanks to crosslinks formation, which reduced water sorption as well. Color change was not significant, and, on the other hand, glossiness was reduced but resulted as more homogeneous than control. CNC addition gave good results also in blue stain protection. CNC improved scratch resistance, but no visible change to impact was registered. CNC has promising results in coatings depending on wood and fungal species and presence of further commercial additives (biocides).
- 21 January 2023
- Published by MDPI AG in Nanomaterials
- Vol. 13 (3) , 442
Open AccessCellulose Nano Crystals (CNC) as Additive for a Bio-Based Waterborne Acrylic Wood Coating: Decay, Artificial Weathering, Physical and Chemical Tests
Wood coatings prolong the service life of wood-based products, but they are usually of synthetic origin. The aim of the present article is to reduce the fossil-based compounds in a commercial waterborne acrylic coating by CNC addition and to test its performance. The coatings were applied on European beech and Norway spruce wood in order to test durability against Gloeophyllum trabeum (brown wood rot) and Trametes versicolor (white wood rot). Artificial weathering and blue stain, contact angle, physical tests (adhesion, impact and scratch test), chemical (FTIR) and morpho-anatomical analysis (SEM) were carried out. CNC addition increased viscosity, limiting the spreading of the coating into wood pores as visible after SEM observation, which reduced coating adhesion on the substrate. CNC improved fungal resistance as seen by a reduced mass loss and FTIR spectroscopy thanks to crosslinks formation, which reduced water sorption as well. Color change was not significant, and, on the other hand, glossiness was reduced but resulted as more homogeneous than control. CNC addition gave good results also in blue stain protection. CNC improved scratch resistance, but no visible change to impact was registered. CNC has promising results in coatings depending on wood and fungal species and presence of further commercial additives (biocides).