Philippe Lours
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Philippe Lours has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Vincent Velay
Université de Toulouse
2 shared publications Akinola Ajayi
1 shared publicationD. Delagnes
Université de Toulouse Institut Clément Ader Ecole des Mines Albi Campus Jarlard, F-81013 Albi, France
1 shared publication- Etienne Copin
Université de Toulouse
1 shared publication F. Taina
Université de Toulouse Institut Clément Ader Ecole des Mines Albi Campus Jarlard, F-81013 Albi, France
1 shared publication- Gérard Bernhart
Université de Toulouse
1 shared publication
Latest Publications
- 22 April 2025
- Published by Elsevier in Ceramics International
- Vol. 51 (20) , 30618-30631
Photoluminescence evolution in APS-deposited YSZ:Eu3+ thermal barrier coatings: mechanisms and sensitivity to thermal history over 0–800 h isothermal exposure at 1100 °C
- 22 April 2025
- Published by Elsevier in Ceramics International
- Vol. 51 (20) , 30618-30631
Photoluminescence evolution in APS-deposited YSZ:Eu3+ thermal barrier coatings: mechanisms and sensitivity to thermal history over 0–800 h isothermal exposure at 1100 °C
- 30 May 2023
- Published by Association for Materials Protection and Performance (AMPP) in Corrosion
- Vol. 79 (8) , 944-956
Stress Corrosion Cracking Behavior of Austenitic Stainless Steel 316L Produced Using Laser-Based Powder Bed Fusion
Austenitic stainless steel UNS S31603 (SS316L) is widely used in the resources industry due to its excellent corrosion resistance, ductility, and weldability. Recently, laser-based powder bed fusion (LPBF) manufacturing has gained popularity for creating SS316L components with complex geometries and superior mechanical properties. However, the rapid melting and solidification of the deposited layers during the thermal cycle of LPBF produce residual stresses. Components manufactured through LPBF are frequently used under applied stress in corrosive environments. Thus, it is crucial to understand their susceptibility to stress corrosion cracking (SCC) and the impact of residual stresses. This study investigated the combined effects of applied stress and temperature on the SCC behavior of LPBF SS316L using custom-made C-ring test specimens. Cold-drawn wrought SS316L was included for comparison. Stress relief heat treatment, microhardness testing, partial immersion testing, and microanalysis techniques, such as light optical microscopy, scanning electron microscopy, and electron backsacttered diffraction were used to quantify the SCC behavior. The outcomes of this study showed that stressed and unstressed LPBF SS316L specimens were highly susceptible to cracking around their printed holes. The SCC susceptibility was attributed to the residual stresses introduced by the printed supports, as both polished and as-printed holes showed similar cracking behavior. This work provides valuable insights and lays a foundation for further research into the impact of using C ring samples to investigate SCC susceptibility and sheds light on the SCC susceptibility of as-printed components of complex geometry printed with supports due to the influence of residual stresses.
- 30 May 2023
- Published by Association for Materials Protection and Performance (AMPP) in Corrosion
- Vol. 79 (8) , 944-956
Stress Corrosion Cracking Behavior of Austenitic Stainless Steel 316L Produced Using Laser-Based Powder Bed Fusion
Austenitic stainless steel UNS S31603 (SS316L) is widely used in the resources industry due to its excellent corrosion resistance, ductility, and weldability. Recently, laser-based powder bed fusion (LPBF) manufacturing has gained popularity for creating SS316L components with complex geometries and superior mechanical properties. However, the rapid melting and solidification of the deposited layers during the thermal cycle of LPBF produce residual stresses. Components manufactured through LPBF are frequently used under applied stress in corrosive environments. Thus, it is crucial to understand their susceptibility to stress corrosion cracking (SCC) and the impact of residual stresses. This study investigated the combined effects of applied stress and temperature on the SCC behavior of LPBF SS316L using custom-made C-ring test specimens. Cold-drawn wrought SS316L was included for comparison. Stress relief heat treatment, microhardness testing, partial immersion testing, and microanalysis techniques, such as light optical microscopy, scanning electron microscopy, and electron backsacttered diffraction were used to quantify the SCC behavior. The outcomes of this study showed that stressed and unstressed LPBF SS316L specimens were highly susceptible to cracking around their printed holes. The SCC susceptibility was attributed to the residual stresses introduced by the printed supports, as both polished and as-printed holes showed similar cracking behavior. This work provides valuable insights and lays a foundation for further research into the impact of using C ring samples to investigate SCC susceptibility and sheds light on the SCC susceptibility of as-printed components of complex geometry printed with supports due to the influence of residual stresses.
- Open Access
- 1 June 2010
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 433, 77-84
Heat Resistant Ni-Cr-Fe Steels for Superplastic Forming Dies: From Material Microstructure to Die Design
Superplasticity in Advanced Materials - ICSAM 2009: Heat Resistant Ni-Cr-Fe Steels for Superplastic Forming Dies: From Material Microstructure to Die Design
- 1 June 2010
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 433, 77-84
Open AccessHeat Resistant Ni-Cr-Fe Steels for Superplastic Forming Dies: From Material Microstructure to Die Design
Superplasticity in Advanced Materials - ICSAM 2009: Heat Resistant Ni-Cr-Fe Steels for Superplastic Forming Dies: From Material Microstructure to Die Design
- Open Access
- 1 January 2010
- Published by The Minerals, Metals and Materials Society
- p. 893-905
Effect of the LCF Loading Cycle Characteristics on the Fatigue Life of Inconel 718 at High Temperature
- 1 January 2010
- Published by The Minerals, Metals and Materials Society
- p. 893-905
Open AccessEffect of the LCF Loading Cycle Characteristics on the Fatigue Life of Inconel 718 at High Temperature