Jean-François Gleyze
Research Subjects
Research Interests
Jean-François Gleyze has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
Nadja Roquin
Le Barp
7 shared publicationsMartin Cormier
Le Barp
5 shared publicationsJean-Yves Natoli
CNRS, Centrale Med., Institut Fresnel
4 shared publications- Laurent Lamaignère
CEA CESTA, F-33116 Le Barp, France
4 shared publications - Charles Bouyer
CEA CESTA
3 shared publications Laurent Lamaignère
CEA CESTA, 15 Ave Sablieres,CS 60001, F-33116 Le Barp, France
3 shared publications
Latest Publications
- Open Access
- 8 July 2026
- Published by Cambridge University Press (CUP) in High Power Laser Science and Engineering
- Vol. 14, 1-10
Effect of beam polarization on a fused silica component damaged with a nanosecond ultraviolet laser beam
Circular laser beam polarization is known to be an alternative tool to increase the damage resistance of optical components to ultraviolet (UV) laser irradiation. In this work, we carefully study its influence on the nonlinear processes mainly responsible for laser damage, which are the Kerr effect and the photo-ionization process. In particular, we show that the circular polarization benefit in the UV domain is mainly observable on thick optical samples. Whatever the laser beam spatial shape is, there is no gain when using circular polarization with thin optical components for nanosecond UV laser beam when the fluence is lower than 25 J/cm 2 . Moreover, our measurements show that laser polarization has no impact on damage growth.
- 8 July 2026
- Published by Cambridge University Press (CUP) in High Power Laser Science and Engineering
- Vol. 14, 1-10
Open AccessEffect of beam polarization on a fused silica component damaged with a nanosecond ultraviolet laser beam
Circular laser beam polarization is known to be an alternative tool to increase the damage resistance of optical components to ultraviolet (UV) laser irradiation. In this work, we carefully study its influence on the nonlinear processes mainly responsible for laser damage, which are the Kerr effect and the photo-ionization process. In particular, we show that the circular polarization benefit in the UV domain is mainly observable on thick optical samples. Whatever the laser beam spatial shape is, there is no gain when using circular polarization with thin optical components for nanosecond UV laser beam when the fluence is lower than 25 J/cm 2 . Moreover, our measurements show that laser polarization has no impact on damage growth.
- 24 March 2026
- Published by Optica Publishing Group in Optics Express
- Vol. 34 (7) , 11890-11902
Impact of the electric field enhancement on the laser damage resistance of transmission gratings operating in the UV and nanosecond regime
The Megajoule Laser (LMJ) uses large transmission diffraction gratings composed of fused silica to focus high-energy laser beams at 351 nm. These gratings operate in the final stage of the laser beamline and must withstand high-energy nanosecond pulses. Increasing the laser-induced damage threshold (LIDT) of transmission gratings is a challenge that requires a detailed understanding of the damage process. Here we numerically and experimentally study the LIDT of silica-based transmission gratings as a function of the electric field intensities (EFI) occurring in the vicinity of the nanostructured surface of diffraction gratings. Damage tests are performed on different samples under varying polarizations and incident angles and compared with numerical EFI simulations. We show that the damage threshold is strongly correlated with the maximum EFI occurring inside the silica pillars of the grating. We evidence a linear relation between the LIDT and the EFI with parameters depending on the sample quality.
- 24 March 2026
- Published by Optica Publishing Group in Optics Express
- Vol. 34 (7) , 11890-11902
Impact of the electric field enhancement on the laser damage resistance of transmission gratings operating in the UV and nanosecond regime
The Megajoule Laser (LMJ) uses large transmission diffraction gratings composed of fused silica to focus high-energy laser beams at 351 nm. These gratings operate in the final stage of the laser beamline and must withstand high-energy nanosecond pulses. Increasing the laser-induced damage threshold (LIDT) of transmission gratings is a challenge that requires a detailed understanding of the damage process. Here we numerically and experimentally study the LIDT of silica-based transmission gratings as a function of the electric field intensities (EFI) occurring in the vicinity of the nanostructured surface of diffraction gratings. Damage tests are performed on different samples under varying polarizations and incident angles and compared with numerical EFI simulations. We show that the damage threshold is strongly correlated with the maximum EFI occurring inside the silica pillars of the grating. We evidence a linear relation between the LIDT and the EFI with parameters depending on the sample quality.
- 21 November 2025
- Published by Optica Publishing Group in Optics Letters
- Vol. 50 (23) , 7300-7303
Effect of shot number on laser damage of fused silica: experimental test of the Max-of-N model
Laser-induced damage initiation on the exit surface of fused silica optics triggered by nanosecond pulses at 351 nm is mostly studied for single laser shots. In this paper, we experimentally investigate how the number of laser shots influences the number of initiated damage sites in the case of an unstable laser beam. More precisely, our experiments question the validity of the “Max-of-N” model [Liao et al. , Appl. Opt. 50 , 3547 ( 2011 ) 10.1364/AO.50.003547 ]. Results show that, in some cases, the modSel correctly predicts the laser damage risk. However, in other cases, it overestimates the damage. We attribute this phenomenon to an increase in the laser damage resistance of the optic, known as laser conditioning, occurring during successive laser shots.
- 21 November 2025
- Published by Optica Publishing Group in Optics Letters
- Vol. 50 (23) , 7300-7303
Effect of shot number on laser damage of fused silica: experimental test of the Max-of-N model
Laser-induced damage initiation on the exit surface of fused silica optics triggered by nanosecond pulses at 351 nm is mostly studied for single laser shots. In this paper, we experimentally investigate how the number of laser shots influences the number of initiated damage sites in the case of an unstable laser beam. More precisely, our experiments question the validity of the “Max-of-N” model [Liao et al. , Appl. Opt. 50 , 3547 ( 2011 ) 10.1364/AO.50.003547 ]. Results show that, in some cases, the modSel correctly predicts the laser damage risk. However, in other cases, it overestimates the damage. We attribute this phenomenon to an increase in the laser damage resistance of the optic, known as laser conditioning, occurring during successive laser shots.
- Open Access
- 2 April 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 137 (13)
Study on the ablation evolution and surface morphology of fused silica as function of CO2 laser processing parameters
In this work, CO2 laser pulses with a wavelength of 10.6 μm, a beam diameter of about 400 μm, and an intensity of the order of 190 kW/cm2 are used to produce microablations on fused silica samples with pulse fluences ranging from the silica ablation threshold up to 38 J/cm2. We obtain pits with average depths ranging from a few nanometers to tens of micrometers and study their morphology evolution as a function of pulse width and pulse-repetition frequency. Our experimental results are used to improve a 2D axisymmetric finite-element model that analyzes the heat transfer process of CO2 laser ablation in fused silica. We propose an empirical function added to the reflection coefficient parameter, which is triggered when the material temperature exceeds its boiling temperature. This empirical function helps to control the energy deposited on the surface material and, as a result, ensures more precise calculations of pit depths for a large range of pulse widths and pulse-repetition frequencies. The improvements made to the 2D axisymmetric model are tested on a 3D model whose results are compared to microchannels ablated with different processing parameters (e.g., scanning speed, pulse-repetition frequency, and pulse width). Good agreement between experimental and numerical results was obtained. The numerical results provide a comprehensive understanding of the evolution of the residual surface temperature and heat-affected zones of the material as a function of pulse width and pulse-repetition frequency.
- 2 April 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 137 (13)
Open AccessStudy on the ablation evolution and surface morphology of fused silica as function of CO2 laser processing parameters
In this work, CO2 laser pulses with a wavelength of 10.6 μm, a beam diameter of about 400 μm, and an intensity of the order of 190 kW/cm2 are used to produce microablations on fused silica samples with pulse fluences ranging from the silica ablation threshold up to 38 J/cm2. We obtain pits with average depths ranging from a few nanometers to tens of micrometers and study their morphology evolution as a function of pulse width and pulse-repetition frequency. Our experimental results are used to improve a 2D axisymmetric finite-element model that analyzes the heat transfer process of CO2 laser ablation in fused silica. We propose an empirical function added to the reflection coefficient parameter, which is triggered when the material temperature exceeds its boiling temperature. This empirical function helps to control the energy deposited on the surface material and, as a result, ensures more precise calculations of pit depths for a large range of pulse widths and pulse-repetition frequencies. The improvements made to the 2D axisymmetric model are tested on a 3D model whose results are compared to microchannels ablated with different processing parameters (e.g., scanning speed, pulse-repetition frequency, and pulse width). Good agreement between experimental and numerical results was obtained. The numerical results provide a comprehensive understanding of the evolution of the residual surface temperature and heat-affected zones of the material as a function of pulse width and pulse-repetition frequency.
- 2 November 2023
- Published by Optica Publishing Group in Optics Letters
- Vol. 48 (22) , 5835-5838
Laser-induced damage growth of fused silica optics near growth threshold at 351 nm
- 2 November 2023
- Published by Optica Publishing Group in Optics Letters
- Vol. 48 (22) , 5835-5838
Laser-induced damage growth of fused silica optics near growth threshold at 351 nm
- Open Access
- 4 September 2023
- Published by Springer Nature in Nature Communications
- Vol. 14 (1) , 1-10
Linear-to-circular polarization conversion with full-silica meta-optics to reduce nonlinear effects in high-energy lasers
High-energy lasers have benefited from intense efforts to bring light-matter interactions to new standards and to achieve laser fusion ignition. One of the main issues to further increasing laser energy is the resistance of optical materials to high laser fluences, in particular at the final stage of the laser beamline where nonlinear Kerr effects can occur in optical materials and provoke laser filamentation. One promising way to mitigate this process is to reduce the nonlinear susceptibility of the material by switching the polarization from a linear to a circular state. Here, we report a significant reduction in the laser filamentation effect on glass by using a full-silica metamaterial waveplateable to switch the linear-to-circular polarization of high fluence laser beams. This result is achieved through the use of a large size full-silica meta-optics exhibiting nominal polarization conversion associated with an excellent transmission efficiency and wavefront quality, as well as a high laser damage resistance.
- 4 September 2023
- Published by Springer Nature in Nature Communications
- Vol. 14 (1) , 1-10
Open AccessLinear-to-circular polarization conversion with full-silica meta-optics to reduce nonlinear effects in high-energy lasers
High-energy lasers have benefited from intense efforts to bring light-matter interactions to new standards and to achieve laser fusion ignition. One of the main issues to further increasing laser energy is the resistance of optical materials to high laser fluences, in particular at the final stage of the laser beamline where nonlinear Kerr effects can occur in optical materials and provoke laser filamentation. One promising way to mitigate this process is to reduce the nonlinear susceptibility of the material by switching the polarization from a linear to a circular state. Here, we report a significant reduction in the laser filamentation effect on glass by using a full-silica metamaterial waveplateable to switch the linear-to-circular polarization of high fluence laser beams. This result is achieved through the use of a large size full-silica meta-optics exhibiting nominal polarization conversion associated with an excellent transmission efficiency and wavefront quality, as well as a high laser damage resistance.
- 10 August 2023
- Published by Optica Publishing Group in Journal of the Optical Society of America B
- Vol. 40 (9) , 2305-2314
Nonlinear processes and laser damage induced by a temporally modulated nanosecond UV laser beam. Part II: Kerr self-focusing
In this paper, we study the impact of Kerr self-focusing on laser-induced damage of fused silica with temporal modulation. In our experiments, temporal modulations are generated with high bandwidth amplitude modulators between 2 and 10 GHz. Measurement of the spatial profile after propagation is made possible due to a dedicated imaging setup. First results without temporal modulation experimentally and numerically show that the nonlinear gain increases exponentially with intensity. Complementary experiments with temporal modulation at different frequencies show an increase in the nonlinear gain. Eventually, we show that laser-induced damage is enhanced with amplitude modulation, with a dependence on the frequency of the amplitude modulation. Optimization of phase modulation allowed us to mitigate backwards stimulated Brillouin scattering and to focus on the sole impact of Kerr self-focusing on laser-induced damage.
- 10 August 2023
- Published by Optica Publishing Group in Journal of the Optical Society of America B
- Vol. 40 (9) , 2305-2314
Nonlinear processes and laser damage induced by a temporally modulated nanosecond UV laser beam. Part II: Kerr self-focusing
In this paper, we study the impact of Kerr self-focusing on laser-induced damage of fused silica with temporal modulation. In our experiments, temporal modulations are generated with high bandwidth amplitude modulators between 2 and 10 GHz. Measurement of the spatial profile after propagation is made possible due to a dedicated imaging setup. First results without temporal modulation experimentally and numerically show that the nonlinear gain increases exponentially with intensity. Complementary experiments with temporal modulation at different frequencies show an increase in the nonlinear gain. Eventually, we show that laser-induced damage is enhanced with amplitude modulation, with a dependence on the frequency of the amplitude modulation. Optimization of phase modulation allowed us to mitigate backwards stimulated Brillouin scattering and to focus on the sole impact of Kerr self-focusing on laser-induced damage.
- 10 August 2023
- Published by Optica Publishing Group in Journal of the Optical Society of America B
- Vol. 40 (9) , 2296-2304
Nonlinear processes and laser damage induced by a temporally modulated nanosecond UV laser beam. Part I: stimulated Brillouin scattering
- 10 August 2023
- Published by Optica Publishing Group in Journal of the Optical Society of America B
- Vol. 40 (9) , 2296-2304
Nonlinear processes and laser damage induced by a temporally modulated nanosecond UV laser beam. Part I: stimulated Brillouin scattering
- 23 February 2010
- Published by Optica Publishing Group in Applied Optics
- Vol. 49 (7) , 1104-1115
Nonsinusoidal phase modulations for high-power laser performance control: stimulated Brillouin scattering and FM-to-AM conversion
High-power lasers, such as the Laser MegaJoule (LMJ), have to be phase modulated to avoid stimulated Brillouin scattering (SBS) that may strongly damage optics at the end of the laser chain. Current spectral broadening on LMJ is performed with a sinusoidal phase modulation. This pure sinusoidal phase modulation leads to inhomogeneous spectral power densities (SPD). Thus, for a same SBS power threshold, the sinusoidal phase-modulated spectrum has to be larger than the equivalent ideal SPD with isoenergetic peaks. We present in this paper a technique to generate energy-balanced Dirac peaks spectra thanks to nonsinusoidal phase modulations. Thus, we can build a narrower spectrum with a nonsinusoidal phase modulation that has the same SBS threshold as a sinusoidal phase modulation, and we show that FM-to-AM conversion can be strongly reduced, which is of great interest for LMJ laser performance, with reductions up to 40%.
- 23 February 2010
- Published by Optica Publishing Group in Applied Optics
- Vol. 49 (7) , 1104-1115
Nonsinusoidal phase modulations for high-power laser performance control: stimulated Brillouin scattering and FM-to-AM conversion
High-power lasers, such as the Laser MegaJoule (LMJ), have to be phase modulated to avoid stimulated Brillouin scattering (SBS) that may strongly damage optics at the end of the laser chain. Current spectral broadening on LMJ is performed with a sinusoidal phase modulation. This pure sinusoidal phase modulation leads to inhomogeneous spectral power densities (SPD). Thus, for a same SBS power threshold, the sinusoidal phase-modulated spectrum has to be larger than the equivalent ideal SPD with isoenergetic peaks. We present in this paper a technique to generate energy-balanced Dirac peaks spectra thanks to nonsinusoidal phase modulations. Thus, we can build a narrower spectrum with a nonsinusoidal phase modulation that has the same SBS threshold as a sinusoidal phase modulation, and we show that FM-to-AM conversion can be strongly reduced, which is of great interest for LMJ laser performance, with reductions up to 40%.
- Open Access
- 6 July 2009
- Published by Optica Publishing Group in Optics Express
- Vol. 17 (14) , 12109-12120
Demonstration of a true single-shot 100 GHz-bandwidth optical oscilloscope at 1053-1064 nm
We demonstrate an innovating design to validate and to optimise the real-time performance of an all-optical oscilloscope at 1053-1064 nm. A unique broadband pulse is generated by means of frequency beats and of proper optical-shaping, which helps us to evidence a signal bandwidth of 100 GHz and a dynamics range in excess of 25 dB. Gain-narrowing and dispersion effects due to the replication of the input pulse are shown to be the first limitations in the broadband capabilities.
- 6 July 2009
- Published by Optica Publishing Group in Optics Express
- Vol. 17 (14) , 12109-12120
Open AccessDemonstration of a true single-shot 100 GHz-bandwidth optical oscilloscope at 1053-1064 nm
We demonstrate an innovating design to validate and to optimise the real-time performance of an all-optical oscilloscope at 1053-1064 nm. A unique broadband pulse is generated by means of frequency beats and of proper optical-shaping, which helps us to evidence a signal bandwidth of 100 GHz and a dynamics range in excess of 25 dB. Gain-narrowing and dispersion effects due to the replication of the input pulse are shown to be the first limitations in the broadband capabilities.