Chunguang Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Chunguang Liu has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Gangbing Song
University of Houston
3 shared publications - Gaojie Yun
Nanxun Innovation Institute, Zhejiang University of Water Resources and Electric Power, Hangzhou 310018, China
3 shared publications - Jingkai Wang
State Key Laboratory of Coastal and Offshore Engineering, Dalian University of Technology, Dalian 116024, China
3 shared publications - Linsheng Huo
State Key Laboratory of Coastal and Offshore Engineering, Dalian University of Technology, Dalian 116024, China
3 shared publications - Chunxu Xia
College of Architectural Engineering, Dalian University, Dalian, China
1 shared publication Dongyu Luo
Institute of Earthquake Engineering, Dalian University of Technology, Dalian, China
1 shared publication
Latest Publications
- Open Access
- 25 April 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (9) , 4754
Nonlinear Dynamic Analysis of Tall Bridge Piers Under Multidimensional Pulse Earthquakes Considering Varying Damping Ratios
The dynamic response of tall bridge piers with varying damping ratios under three-dimensional pulse ground motion remains insufficiently understood. To control the pulse characteristic parameters accurately and eliminate interference from actual seismic records, this study uses the earthquake wave synthesis software to generate three pulse seismic waves and non-pulse seismic waves with varying seismic characteristic periods. The dynamic response analysis of tall bridge piers under one-dimensional, two-dimensional, and three-dimensional seismic input conditions is carried out. The influence mechanism of pulse effect, damping ratio and ground motion dimension on structural response is mainly discussed. The results show that the peak displacement and peak shear stress response of tall bridge pier structures under pulse ground motion are 0.0614 m and 0.1727 MPa larger than those under non-pulse ground motion, respectively. The responses of the displacement and shear stress of the tall bridge pier subjected to pulse ground motion exceed those under non-pulse ground motion. When the action time exceeds 18 s, the influence on the displacement and shear stress time history curve of the tall bridge pier is ranked as follows: pulse ground motion > damping ratio > non-pulse ground motion. Under multidimensional non-pulse ground motion, the maximum errors in peak displacement at the Z section and peak shear stress at the YZ section of a tall bridge pier are 0.05% and 5.27%, respectively. These errors increase to 0.67% and 1.68% under multidimensional pulse ground motion, respectively. Compared with one-dimensional seismic conditions, two-dimensional and three-dimensional ground motions result in smaller displacement and shear stress errors at the Z section, but larger errors at the X section, particularly for peak displacement and shear stress at the YZ section. This highlights the greater complexity of multidimensional seismic forces and their varying impacts on different sections of tall bridge piers.
- 25 April 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (9) , 4754
Open AccessNonlinear Dynamic Analysis of Tall Bridge Piers Under Multidimensional Pulse Earthquakes Considering Varying Damping Ratios
The dynamic response of tall bridge piers with varying damping ratios under three-dimensional pulse ground motion remains insufficiently understood. To control the pulse characteristic parameters accurately and eliminate interference from actual seismic records, this study uses the earthquake wave synthesis software to generate three pulse seismic waves and non-pulse seismic waves with varying seismic characteristic periods. The dynamic response analysis of tall bridge piers under one-dimensional, two-dimensional, and three-dimensional seismic input conditions is carried out. The influence mechanism of pulse effect, damping ratio and ground motion dimension on structural response is mainly discussed. The results show that the peak displacement and peak shear stress response of tall bridge pier structures under pulse ground motion are 0.0614 m and 0.1727 MPa larger than those under non-pulse ground motion, respectively. The responses of the displacement and shear stress of the tall bridge pier subjected to pulse ground motion exceed those under non-pulse ground motion. When the action time exceeds 18 s, the influence on the displacement and shear stress time history curve of the tall bridge pier is ranked as follows: pulse ground motion > damping ratio > non-pulse ground motion. Under multidimensional non-pulse ground motion, the maximum errors in peak displacement at the Z section and peak shear stress at the YZ section of a tall bridge pier are 0.05% and 5.27%, respectively. These errors increase to 0.67% and 1.68% under multidimensional pulse ground motion, respectively. Compared with one-dimensional seismic conditions, two-dimensional and three-dimensional ground motions result in smaller displacement and shear stress errors at the Z section, but larger errors at the X section, particularly for peak displacement and shear stress at the YZ section. This highlights the greater complexity of multidimensional seismic forces and their varying impacts on different sections of tall bridge piers.
- Open Access
- 19 November 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (22) , 10709
Study on the Hydrodynamic Effects of Bridge Piers Under Velocity-Type Pulse Ground Motion Based on Different Characteristic Periods
This study was based on a target spectrum (GB183062015) and synthesized different characteristic periods, pulse ground motions, and non-pulse ground motions utilizing EQsignal v1.2.1 software. It also investigated the dynamic behaviors of bridge piers in seismic motions with varying characteristic periods, pulse and non-pulse effects, and the influence of 0 m and 10 m water depths. The findings indicated that the peak acceleration and stress behaviors vary significantly under different characteristic periods of ground motion. The maximum error in peak acceleration behavior of a bridge pier under ground motions of varying characteristic periods is 19.25%, while the maximum error in peak stress response is 11.35%. The acceleration and stress behaviors of a bridge pier under pulse ground motion action are more considerable than those under non-pulse seismic motion action. When the characteristic period is 0.40 s, the maximum error in peak acceleration of the bridge pier structure under pulse seismic motion and non-pulse seismic motion action is 86.08%, with the maximum error of the peak stress reaches 80.68%. The existence of water serves to minimize the natural frequency of the bridge pier. The pulse effects result in a maximum error of 40.49% for the peak acceleration and a maximum discrepancy of 323.08% for the peak stress of the bridge pier. The hydrodynamic effects result in a maximum error of 33.51% for the acceleration peak and 12.90% for the stress peak of the bridge pier. The effect of the pulse symptoms on the dynamic behavior of the bridge pier is considerably more pronounced than that of the hydrodynamic effects, with an intricate and complex influencing mechanism. In bridge flood protection and seismic design and optimization, it is essential to consider the impact of pulse seismic motion with varying characteristic periods.
- 19 November 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (22) , 10709
Open AccessStudy on the Hydrodynamic Effects of Bridge Piers Under Velocity-Type Pulse Ground Motion Based on Different Characteristic Periods
This study was based on a target spectrum (GB183062015) and synthesized different characteristic periods, pulse ground motions, and non-pulse ground motions utilizing EQsignal v1.2.1 software. It also investigated the dynamic behaviors of bridge piers in seismic motions with varying characteristic periods, pulse and non-pulse effects, and the influence of 0 m and 10 m water depths. The findings indicated that the peak acceleration and stress behaviors vary significantly under different characteristic periods of ground motion. The maximum error in peak acceleration behavior of a bridge pier under ground motions of varying characteristic periods is 19.25%, while the maximum error in peak stress response is 11.35%. The acceleration and stress behaviors of a bridge pier under pulse ground motion action are more considerable than those under non-pulse seismic motion action. When the characteristic period is 0.40 s, the maximum error in peak acceleration of the bridge pier structure under pulse seismic motion and non-pulse seismic motion action is 86.08%, with the maximum error of the peak stress reaches 80.68%. The existence of water serves to minimize the natural frequency of the bridge pier. The pulse effects result in a maximum error of 40.49% for the peak acceleration and a maximum discrepancy of 323.08% for the peak stress of the bridge pier. The hydrodynamic effects result in a maximum error of 33.51% for the acceleration peak and 12.90% for the stress peak of the bridge pier. The effect of the pulse symptoms on the dynamic behavior of the bridge pier is considerably more pronounced than that of the hydrodynamic effects, with an intricate and complex influencing mechanism. In bridge flood protection and seismic design and optimization, it is essential to consider the impact of pulse seismic motion with varying characteristic periods.
- Open Access
- 29 July 2024
- Published by MDPI AG in Sustainability
- Vol. 16 (15) , 6486
Nonlinear Dynamic Analysis of High-Strength Concrete Bridges under Post-Fire Earthquakes Considering Hydrodynamic Effects
This study employed the linear interpolation method to ascertain the curve relationship between the elastic modulus and stress of high-strength concrete C60 with temperature, and the nonlinear dynamic analysis of high-strength concrete bridge structures subjected to post-fire earthquake action at varying water levels was subsequently evaluated. It was established that both the hydrodynamic effects and the temperature effects have a considerable impact on the structural dynamic response of bridges. The presence of water has been observed to increase the dynamic response of pier structures. At water levels of 0 m and 10 m, the temperature effect results in a reduction in the fundamental frequencies of acceleration and displacement responses by 73.68% and a decrease in the fundamental frequency of stress responses by 83.33%. At a water level of 20 m, the fundamental frequencies of the acceleration, displacement, and stress responses decrease by 53.49%. In consideration of the acceleration and displacement at the pier top and stress at the pier base at a water depth of 10 m, the superposition of temperature effects and hydrodynamic effects results in an increase of 59.06% in acceleration, 25.93% in displacement, and 49.53% in stress than combination effects, respectively. At a water depth of 20 m, the superposition of temperature and hydrodynamic effects results in an increase of 92.82%, 100%, and 127.85% in acceleration, displacement, and stress, respectively. The combined effects of hydrodynamic and temperature effects cannot be described merely as a linear superposition of the two single actions. The research findings provide a significant theoretical basis for understanding the impact of multiple disasters, such as fires and earthquakes, on bridge structures.
- 29 July 2024
- Published by MDPI AG in Sustainability
- Vol. 16 (15) , 6486
Open AccessNonlinear Dynamic Analysis of High-Strength Concrete Bridges under Post-Fire Earthquakes Considering Hydrodynamic Effects
This study employed the linear interpolation method to ascertain the curve relationship between the elastic modulus and stress of high-strength concrete C60 with temperature, and the nonlinear dynamic analysis of high-strength concrete bridge structures subjected to post-fire earthquake action at varying water levels was subsequently evaluated. It was established that both the hydrodynamic effects and the temperature effects have a considerable impact on the structural dynamic response of bridges. The presence of water has been observed to increase the dynamic response of pier structures. At water levels of 0 m and 10 m, the temperature effect results in a reduction in the fundamental frequencies of acceleration and displacement responses by 73.68% and a decrease in the fundamental frequency of stress responses by 83.33%. At a water level of 20 m, the fundamental frequencies of the acceleration, displacement, and stress responses decrease by 53.49%. In consideration of the acceleration and displacement at the pier top and stress at the pier base at a water depth of 10 m, the superposition of temperature effects and hydrodynamic effects results in an increase of 59.06% in acceleration, 25.93% in displacement, and 49.53% in stress than combination effects, respectively. At a water depth of 20 m, the superposition of temperature and hydrodynamic effects results in an increase of 92.82%, 100%, and 127.85% in acceleration, displacement, and stress, respectively. The combined effects of hydrodynamic and temperature effects cannot be described merely as a linear superposition of the two single actions. The research findings provide a significant theoretical basis for understanding the impact of multiple disasters, such as fires and earthquakes, on bridge structures.
- Open Access
- 21 August 2023
- Published by Wiley in Structural Control and Health Monitoring
- Vol. 2023, 1-16
Theoretical and Experimental Study on Homologous Acoustic Emission Signal Recognition Based on Synchrosqueezed Wavelet Transform Coherence
The acoustic emission (AE) technique has been widely investigated for its ability to locate damage in structures. However, the selection of the arrival point of AE signals and the existence of nonhomologous AE signals can significantly affect the location accuracy of damages. The synchrosqueezed wavelet transform (SWT) was used in our previous research to pick the accurate arrival point, but the existence of the nonhomologous signals was neglected in the picking process. To address this limitation, the synchrosqueezed wavelet transform coherence (SWTC) method is proposed to improve the accuracy by recognizing homologous signals and suppressing the spectral leakage in this paper. Compared with the wavelet transform coherence (WTC) method previously used, the SWTC method using the squeezing wavelet coefficients obtained by the SWT can constitute a more explicit coherence graph of AE signals. This clear coherence graph can help reduce the effect of subjective factors in observing the coherence and improve the recognition accuracy of homologous signals. The effectiveness of the proposed method is experimentally verified on a steel pipe and a concrete beam. The results demonstrate that the SWTC accurately identifies homologous AE signals and effectively improves the localization accuracy across different signal densities, localization distances, and materials.
- 21 August 2023
- Published by Wiley in Structural Control and Health Monitoring
- Vol. 2023, 1-16
Open AccessTheoretical and Experimental Study on Homologous Acoustic Emission Signal Recognition Based on Synchrosqueezed Wavelet Transform Coherence
The acoustic emission (AE) technique has been widely investigated for its ability to locate damage in structures. However, the selection of the arrival point of AE signals and the existence of nonhomologous AE signals can significantly affect the location accuracy of damages. The synchrosqueezed wavelet transform (SWT) was used in our previous research to pick the accurate arrival point, but the existence of the nonhomologous signals was neglected in the picking process. To address this limitation, the synchrosqueezed wavelet transform coherence (SWTC) method is proposed to improve the accuracy by recognizing homologous signals and suppressing the spectral leakage in this paper. Compared with the wavelet transform coherence (WTC) method previously used, the SWTC method using the squeezing wavelet coefficients obtained by the SWT can constitute a more explicit coherence graph of AE signals. This clear coherence graph can help reduce the effect of subjective factors in observing the coherence and improve the recognition accuracy of homologous signals. The effectiveness of the proposed method is experimentally verified on a steel pipe and a concrete beam. The results demonstrate that the SWTC accurately identifies homologous AE signals and effectively improves the localization accuracy across different signal densities, localization distances, and materials.
- Open Access
Multitype Damage Imaging in Concrete Modeling Based on Time Reversal Technique
It is necessary to develop effective methods for visually detecting concrete damage because minor damage can affect the performance of concrete materials. However, the non-homogeneous nature of concrete materials limits the application of imaging algorithms that have been widely used in aerospace and mechanical fields; thus, obtaining high-resolution imaging maps is difficult. In this study, feasibility research on concrete damage detection was conducted using the time reversal focusing imaging algorithm. A new method for characterizing various concrete damage conditions with focusing curves was proposed. ABAQUS software was utilized to establish five types of concrete damage, and the imaging quality of the proposed method was evaluated in Python. The effect of the relative position of the damage and the sensors was analyzed. The focusing curve was extracted from the imaging area to further explain the image information. The numerical simulation results show that time reversal focusing had better damage localization than the forward algorithm; time focusing also improved the spatial focusing quality. In addition, focusing curves were used to extract information from the main lobe and to determine the size and location of the damage.
Open AccessMultitype Damage Imaging in Concrete Modeling Based on Time Reversal Technique
It is necessary to develop effective methods for visually detecting concrete damage because minor damage can affect the performance of concrete materials. However, the non-homogeneous nature of concrete materials limits the application of imaging algorithms that have been widely used in aerospace and mechanical fields; thus, obtaining high-resolution imaging maps is difficult. In this study, feasibility research on concrete damage detection was conducted using the time reversal focusing imaging algorithm. A new method for characterizing various concrete damage conditions with focusing curves was proposed. ABAQUS software was utilized to establish five types of concrete damage, and the imaging quality of the proposed method was evaluated in Python. The effect of the relative position of the damage and the sensors was analyzed. The focusing curve was extracted from the imaging area to further explain the image information. The numerical simulation results show that time reversal focusing had better damage localization than the forward algorithm; time focusing also improved the spatial focusing quality. In addition, focusing curves were used to extract information from the main lobe and to determine the size and location of the damage.
- 4 June 2020
- Published by Taylor & Francis in Journal of Earthquake Engineering
- Vol. 26 (6) , 2846-2866
Damping Effect of Insulation on a Liquefied Natural Gas Tank Based on Shaking Table Tests
Full-capacity large-scale liquefied natural gas (LNG) tanks comprise a steel inner tank and a concrete outer tank. The space between the walls of these two tanks is filled with expanded perlite and a resilient blanket as an insulation layer. It is well known that interactions between the outer tank, insulation, inner tank, and liquid occur under seismic loads. In this study, to investigate the effect of insulation on an LNG tank, a scale model of the tank was constructed, and shaking table tests were conducted with and without insulation at different liquid levels. A comparison of the displacement, acceleration, and axial strain of the tank walls at different test conditions indicates that the insulation exerts good damping effects on the responses of the inner tank wall. Additionally, it has a certain restraining effect on the acceleration of the outer tank wall. However, its damping effect on the displacement and axial strain of the outer tank wall is negligible; in fact, it can even amplify them. Furthermore, most of the maximum seismic responses occur at the full liquid level, for which the effects of the insulation on the tank are more evident than at other liquid levels.
- 4 June 2020
- Published by Taylor & Francis in Journal of Earthquake Engineering
- Vol. 26 (6) , 2846-2866
Damping Effect of Insulation on a Liquefied Natural Gas Tank Based on Shaking Table Tests
Full-capacity large-scale liquefied natural gas (LNG) tanks comprise a steel inner tank and a concrete outer tank. The space between the walls of these two tanks is filled with expanded perlite and a resilient blanket as an insulation layer. It is well known that interactions between the outer tank, insulation, inner tank, and liquid occur under seismic loads. In this study, to investigate the effect of insulation on an LNG tank, a scale model of the tank was constructed, and shaking table tests were conducted with and without insulation at different liquid levels. A comparison of the displacement, acceleration, and axial strain of the tank walls at different test conditions indicates that the insulation exerts good damping effects on the responses of the inner tank wall. Additionally, it has a certain restraining effect on the acceleration of the outer tank wall. However, its damping effect on the displacement and axial strain of the outer tank wall is negligible; in fact, it can even amplify them. Furthermore, most of the maximum seismic responses occur at the full liquid level, for which the effects of the insulation on the tank are more evident than at other liquid levels.
- Open Access
- 12 January 2019
- Published by MDPI AG in Applied Sciences
- Vol. 9 (2) , 259
Identification and Representation of Multi-Pulse Near-Fault Strong Ground Motion Using Adaptive Wavelet Transform
In order to identify the horizontal seismic motion owning the largest pulse energy, and represent the dominant pulse-like component embedded in this seismic motion, we used the adaptive wavelet transform algorithm in this paper. Fifteen candidate mother wavelets were evaluated to select the optimum wavelet based on the similarities between the candidate mother wavelet and the target seismic motion, evaluated by the minimum cross variance. This adaptive choosing algorithm for the optimum mother wavelet was invoked before identifying both the horizontal direction owning the largest pulse energy and every dominant pulse, which provides the optimum mother wavelet for the continuous wavelet transform. Each dominant pulse can be represented by its adaptively selected optimum mother wavelet. The results indicate that the identified multi-pulse component fits well with the seismic motion. In most cases, mother wavelets in one multi-pulse seismic motion were different from each other. For the Chi-Chi event (1999-Sep-20 17:47:16 UTC, Mw = 7.6), 62.26% of the qualified pulse-like earthquake motions lay in the horizontal direction ranging from ±15° to ±75°. The Daubechies 6 (db6) mother wavelet was the most frequently used type for both the first and second pulse components.
- 12 January 2019
- Published by MDPI AG in Applied Sciences
- Vol. 9 (2) , 259
Open AccessIdentification and Representation of Multi-Pulse Near-Fault Strong Ground Motion Using Adaptive Wavelet Transform
In order to identify the horizontal seismic motion owning the largest pulse energy, and represent the dominant pulse-like component embedded in this seismic motion, we used the adaptive wavelet transform algorithm in this paper. Fifteen candidate mother wavelets were evaluated to select the optimum wavelet based on the similarities between the candidate mother wavelet and the target seismic motion, evaluated by the minimum cross variance. This adaptive choosing algorithm for the optimum mother wavelet was invoked before identifying both the horizontal direction owning the largest pulse energy and every dominant pulse, which provides the optimum mother wavelet for the continuous wavelet transform. Each dominant pulse can be represented by its adaptively selected optimum mother wavelet. The results indicate that the identified multi-pulse component fits well with the seismic motion. In most cases, mother wavelets in one multi-pulse seismic motion were different from each other. For the Chi-Chi event (1999-Sep-20 17:47:16 UTC, Mw = 7.6), 62.26% of the qualified pulse-like earthquake motions lay in the horizontal direction ranging from ±15° to ±75°. The Daubechies 6 (db6) mother wavelet was the most frequently used type for both the first and second pulse components.
- Open Access
Wear Degree Quantification of Pin Connections Using Parameter-Based Analyses of Acoustic Emissions
Pin connections are commonly used in many engineering fields, and continuous operation may cause severe wear on the pins and may lead to their eventual fracture, if undetected. However, a reliable nonintrusive real-time method to monitor the wear of pin connections is yet to be developed. In this paper, acoustic emission (AE)-based parametric analysis methods, including the logarithm of the cumulative energy (LAE), the logarithm of the slope of cumulative energy (LSCE), the b-value method, the Ib-value method, and the fast Fourier transformation (FFT), were developed to quantify the wear degree of pin connections. The b-value method offers a criterion to quickly judge whether severe wear occurs on a pin connection. To assist the research, an experimental apparatus to accelerate wear test of pin connections was designed and fabricated. The AE sensor, mounted on the test apparatus in a nondestructive manner, is capable of real-time monitoring. The micrographs of the wear of pins, and the surface roughness of pins, verified that the values of the max LAE and the max LSCE became larger as the wear degree of pin connections increased, which means different values of the max LAE and the max LSCE can reflect different wear degree of pin connections. Meanwhile, the results of the micrographs and surface roughness confirmed that the b-value is an effective method to identify severe wear, and the value “1” can be used as a criterion to detect severe damage in different structures. Furthermore, the results of spectrum analysis in the low frequency range showed that the wear frequency was concentrated in the range of 0.01 to 0.02 MHz for the pin connection. This study demonstrated that these methods, developed based on acoustic emission technique, can be utilized in quantifying the wear degree of pin connections in a nondestructive way.
Open AccessWear Degree Quantification of Pin Connections Using Parameter-Based Analyses of Acoustic Emissions
Pin connections are commonly used in many engineering fields, and continuous operation may cause severe wear on the pins and may lead to their eventual fracture, if undetected. However, a reliable nonintrusive real-time method to monitor the wear of pin connections is yet to be developed. In this paper, acoustic emission (AE)-based parametric analysis methods, including the logarithm of the cumulative energy (LAE), the logarithm of the slope of cumulative energy (LSCE), the b-value method, the Ib-value method, and the fast Fourier transformation (FFT), were developed to quantify the wear degree of pin connections. The b-value method offers a criterion to quickly judge whether severe wear occurs on a pin connection. To assist the research, an experimental apparatus to accelerate wear test of pin connections was designed and fabricated. The AE sensor, mounted on the test apparatus in a nondestructive manner, is capable of real-time monitoring. The micrographs of the wear of pins, and the surface roughness of pins, verified that the values of the max LAE and the max LSCE became larger as the wear degree of pin connections increased, which means different values of the max LAE and the max LSCE can reflect different wear degree of pin connections. Meanwhile, the results of the micrographs and surface roughness confirmed that the b-value is an effective method to identify severe wear, and the value “1” can be used as a criterion to detect severe damage in different structures. Furthermore, the results of spectrum analysis in the low frequency range showed that the wear frequency was concentrated in the range of 0.01 to 0.02 MHz for the pin connection. This study demonstrated that these methods, developed based on acoustic emission technique, can be utilized in quantifying the wear degree of pin connections in a nondestructive way.
- Open Access
- 30 September 2018
- Published by MDPI AG in Applied Sciences
- Vol. 8 (10) , 1775
Feasibility Study of Real-Time Monitoring of Pin Connection Wear Using Acoustic Emission
Pin connections are one of the most important connecting forms and they have been widely used in engineering fields. In its service, pin connections are subject to wear, and it will be beneficial if the health condition of pin connections can be monitored in real time. In this paper, an acoustic emission (AE)-based method was developed to monitor wear degree of low rotational speed pin connections in real time in a nondestructive way. Most pin connections are operated at low rotational speed. To facilitate the research, an experimental apparatus to accelerate the wear test of low rotational speed pin connections was designed and fabricated. The piezoceramic AE sensor was mounted on the test apparatus in a nondestructive way, and it was capable of real-time monitoring. Accelerated wear tests of low rotational speed pin connections were conducted. To verify the results of the AE technique, a VHX-600E digital (from Keyence, Osaka, Japan) microscope was applied to observe the micrographs of the tested pins. The experimental results show that AE activity existed throughout the entire wear process, and it was the most prominent in the serious wear phase. The wear degree of the pin connections can be reflected qualitatively by the signal strength and the accumulative signal strength of the AE signals. In addition, two different wear forms can be distinguished by comparing the signal strength values of all specimens. Micrographs of all specimens confirm these results, and determine that the two wear forms include adhesive wear and abrasive wear. Furthermore, AE results demonstrated that adhesive wear is the main mode of wear for the low rotational speed pin connections, and the signal strength of the adhesive wear is around 190 times larger than that of abrasive wear. This feasibility study demonstrated that the developed acoustic emission technique can be utilized in the wear monitoring of pin connections in real time in a nondestructive way.
- 30 September 2018
- Published by MDPI AG in Applied Sciences
- Vol. 8 (10) , 1775
Open AccessFeasibility Study of Real-Time Monitoring of Pin Connection Wear Using Acoustic Emission
Pin connections are one of the most important connecting forms and they have been widely used in engineering fields. In its service, pin connections are subject to wear, and it will be beneficial if the health condition of pin connections can be monitored in real time. In this paper, an acoustic emission (AE)-based method was developed to monitor wear degree of low rotational speed pin connections in real time in a nondestructive way. Most pin connections are operated at low rotational speed. To facilitate the research, an experimental apparatus to accelerate the wear test of low rotational speed pin connections was designed and fabricated. The piezoceramic AE sensor was mounted on the test apparatus in a nondestructive way, and it was capable of real-time monitoring. Accelerated wear tests of low rotational speed pin connections were conducted. To verify the results of the AE technique, a VHX-600E digital (from Keyence, Osaka, Japan) microscope was applied to observe the micrographs of the tested pins. The experimental results show that AE activity existed throughout the entire wear process, and it was the most prominent in the serious wear phase. The wear degree of the pin connections can be reflected qualitatively by the signal strength and the accumulative signal strength of the AE signals. In addition, two different wear forms can be distinguished by comparing the signal strength values of all specimens. Micrographs of all specimens confirm these results, and determine that the two wear forms include adhesive wear and abrasive wear. Furthermore, AE results demonstrated that adhesive wear is the main mode of wear for the low rotational speed pin connections, and the signal strength of the adhesive wear is around 190 times larger than that of abrasive wear. This feasibility study demonstrated that the developed acoustic emission technique can be utilized in the wear monitoring of pin connections in real time in a nondestructive way.
- 11 December 2013
- Published by American Society of Civil Engineers (ASCE)
- p. 465-472
Research on Hydrodynamic Pressure of Deep Water Bridge Structure
Bridge system is an important part of the lifeline systems. In order to study the effects of fluid-structure interaction on the dynamic response behavior of deep water bridge structure, an investigation on hydrodynamic pressure is developed in two ways, including theoretical analysis and experimental study. For the purpose of establishing the seismic response-based criterion under earthquake of submerged bridge structure, a set of equations are derived by utilizing Morison theory. Then, a model test of submerged bridge pier system, including pile groups-cap-pier and inertia mass, has been performed to investigate the effect of hydrodynamic pressure on seismic response. Based on the results, the effect of hydrodynamic pressure was analyzed experimentally theoretically. Study results indicate that the surrounding water can change the characteristics of structure, so the effect of hydrodynamic pressure should be paid much attention.
- 11 December 2013
- Published by American Society of Civil Engineers (ASCE)
- p. 465-472
Research on Hydrodynamic Pressure of Deep Water Bridge Structure
Bridge system is an important part of the lifeline systems. In order to study the effects of fluid-structure interaction on the dynamic response behavior of deep water bridge structure, an investigation on hydrodynamic pressure is developed in two ways, including theoretical analysis and experimental study. For the purpose of establishing the seismic response-based criterion under earthquake of submerged bridge structure, a set of equations are derived by utilizing Morison theory. Then, a model test of submerged bridge pier system, including pile groups-cap-pier and inertia mass, has been performed to investigate the effect of hydrodynamic pressure on seismic response. Based on the results, the effect of hydrodynamic pressure was analyzed experimentally theoretically. Study results indicate that the surrounding water can change the characteristics of structure, so the effect of hydrodynamic pressure should be paid much attention.