Changyong Oh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Changyong Oh has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Bo Sung Kim
Department of Applied Physics, Korea University, Sejong 30019, Republic of Korea
2 shared publications - Geon Hyeong Lee
Department of Applied Physics, Korea University, Sejong 30019, Republic of Korea
1 shared publication Hyeong Wook Kim
Department of Applied Physics, Korea University 1 , Sejong 30019, Republic of Korea
1 shared publication- Hyunwuk Kim
Display Development Division, ENF Technology Co., Ltd., Yongin-si 17084, Republic of Korea
1 shared publication - Jun Ho Song
Division of Display and Semiconductor Physics, Korea University, Sejong 30019, Republic of Korea
1 shared publication - Min Young Kim
Department of Applied Physics, Korea University, Sejong 30019, Republic of Korea
1 shared publication
Latest Publications
- Open Access
Influence of Channel Surface with Ozone Annealing and UV Treatment on the Electrical Characteristics of Top-Gate InGaZnO Thin-Film Transistors
The effect of the channel interface of top-gate InGaZnO (IGZO) thin film transistors (TFTs) on the electrical properties caused by exposure to various wet chemicals such as deionized water, photoresist (PR), and strippers during the photolithography process was studied. Contrary to the good electrical characteristics of TFTs including a protective layer (PL) to avoid interface damage by wet chemical processes, TFTs without PL showed a conductive behavior with a negative threshold voltage shift, in which the ratio of Ga and Zn on the IGZO top surface reduced due to exposure to a stripper. In addition, the wet process in photolithography increased oxygen vacancy and oxygen impurity on the IGZO surface. The photo-patterning process increased donor-like defects in IGZO due to organic contamination on the IGZO surface by PR, making the TFT characteristics more conductive. The introduction of ozone (O3) annealing after photo-patterning and stripping of IGZO reduced the increased defect states on the surface of IGZO due to the wet process and effectively eliminated organic contamination by PR. In particular, by controlling surface oxygens on top of the IGZO surface excessively generated with O3 annealing using UV irradiation of 185 and 254 nm, IGZO TFTs with excellent current–voltage characteristics and reliability could be realized comparable to IGZO TFTs containing PL.
Open AccessInfluence of Channel Surface with Ozone Annealing and UV Treatment on the Electrical Characteristics of Top-Gate InGaZnO Thin-Film Transistors
The effect of the channel interface of top-gate InGaZnO (IGZO) thin film transistors (TFTs) on the electrical properties caused by exposure to various wet chemicals such as deionized water, photoresist (PR), and strippers during the photolithography process was studied. Contrary to the good electrical characteristics of TFTs including a protective layer (PL) to avoid interface damage by wet chemical processes, TFTs without PL showed a conductive behavior with a negative threshold voltage shift, in which the ratio of Ga and Zn on the IGZO top surface reduced due to exposure to a stripper. In addition, the wet process in photolithography increased oxygen vacancy and oxygen impurity on the IGZO surface. The photo-patterning process increased donor-like defects in IGZO due to organic contamination on the IGZO surface by PR, making the TFT characteristics more conductive. The introduction of ozone (O3) annealing after photo-patterning and stripping of IGZO reduced the increased defect states on the surface of IGZO due to the wet process and effectively eliminated organic contamination by PR. In particular, by controlling surface oxygens on top of the IGZO surface excessively generated with O3 annealing using UV irradiation of 185 and 254 nm, IGZO TFTs with excellent current–voltage characteristics and reliability could be realized comparable to IGZO TFTs containing PL.
- Open Access
- 22 August 2023
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 41 (5)
Study on effective dry etching of InGaZnO thin films under capacitively coupled plasma-reactive ion etching with a nonfluorine-based etching gas
Dry etching of InGaZnO (IGZO) thin films was performed in a capacitively coupled plasma-reactive ion etching (CCP-RIE) mode using hydrochloride (HCl) and argon (Ar) gases. Dry-etching characteristics and surface properties of IGZO films were then investigated according to gas mixture ratio, radio frequency power, and chamber working pressure. With an optimized ratio of HCl : Ar at 20 : 20 SCCM, the IGZO film showed good etch characteristics with a moderate etch rate of 6.0 nm/min and a low roughness of 0.19 nm. During the etching process of IGZO thin films, nonvolatile by-products such as GaClx, InClx, and ZnClx generated on the surface could be effectively removed by physical bombardment with Ar+ ions. As a result, we successfully conducted dry etching of IGZO thin films in the CCP-RIE system under HCl-Ar gas conditions, which demonstrated dry etching on IGZO without needing a fluorine-based etching gas.
- 22 August 2023
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 41 (5)
Open AccessStudy on effective dry etching of InGaZnO thin films under capacitively coupled plasma-reactive ion etching with a nonfluorine-based etching gas
Dry etching of InGaZnO (IGZO) thin films was performed in a capacitively coupled plasma-reactive ion etching (CCP-RIE) mode using hydrochloride (HCl) and argon (Ar) gases. Dry-etching characteristics and surface properties of IGZO films were then investigated according to gas mixture ratio, radio frequency power, and chamber working pressure. With an optimized ratio of HCl : Ar at 20 : 20 SCCM, the IGZO film showed good etch characteristics with a moderate etch rate of 6.0 nm/min and a low roughness of 0.19 nm. During the etching process of IGZO thin films, nonvolatile by-products such as GaClx, InClx, and ZnClx generated on the surface could be effectively removed by physical bombardment with Ar+ ions. As a result, we successfully conducted dry etching of IGZO thin films in the CCP-RIE system under HCl-Ar gas conditions, which demonstrated dry etching on IGZO without needing a fluorine-based etching gas.