Shiliang Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Shiliang Zhang has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Masayoshi Akiyama
Akiyama Mechanical Engineering Consulting, Kyoto, Japan
2 shared publications - Shohei Kajikawa
電気通信大学 大学院情報理工学研究科 機械知能システム学専
2 shared publications - Takashi Kuboki
The University of Electro-Communications Department of Mechanical and Intelligent Systems Engineering
2 shared publications Masayoshi Akiyama
Akiyama Mechanical Engineering Consulting
1 shared publication- Shohei Kajikawa
The University of Electro-Communications
1 shared publication Takashi Kuboki
The University of Electro-Communications
1 shared publication
Latest Publications
- 8 March 2025
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 137 (5-6) , 2743-2759
Effect of plug geometry on forming accuracy in tube expansion drawing process
- 8 March 2025
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 137 (5-6) , 2743-2759
Effect of plug geometry on forming accuracy in tube expansion drawing process
- 21 May 2024
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 146 (7) , 1-36
Influence of Mechanical Properties of Tube on Forming Limits and Deformation Characteristics in an Expansion Drawing Process
This paper describes an efficient method of manufacturing thin-walled metal tubes. The proposed method is an expansion drawing and it consists of two stages, flaring and drawing, during which high thickness reduction is achieved because the tube being processed is subjected to tensile stress in both the circumferential and axial directions. The optimal plug half-angle for various materials is investigated using a finite element analysis and experiments, revealing the plug shape with the highest expansion limit and the highest thickness reduction ratio. To investigate the deformation characteristics of different materials during the expansion drawing process, the strain in tubes formed using different materials was measured experimentally using a square grid on the outer surface of the tubes. In addition, a finite element analysis using hypothetical material properties revealed that the work-hardening exponent and friction coefficient affect tube deformation. The results of this work explain the influences of material properties on experimentally observed phenomena. Materials with a large work-hardening exponent are less prone to thinning during forming and have a greater forming limit. On the other hand, the larger the friction coefficient between the plug and the mother tube, the larger the deformation in the axial direction was, and then the thickness reduction increased due to biaxial tension.
- 21 May 2024
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 146 (7) , 1-36
Influence of Mechanical Properties of Tube on Forming Limits and Deformation Characteristics in an Expansion Drawing Process
This paper describes an efficient method of manufacturing thin-walled metal tubes. The proposed method is an expansion drawing and it consists of two stages, flaring and drawing, during which high thickness reduction is achieved because the tube being processed is subjected to tensile stress in both the circumferential and axial directions. The optimal plug half-angle for various materials is investigated using a finite element analysis and experiments, revealing the plug shape with the highest expansion limit and the highest thickness reduction ratio. To investigate the deformation characteristics of different materials during the expansion drawing process, the strain in tubes formed using different materials was measured experimentally using a square grid on the outer surface of the tubes. In addition, a finite element analysis using hypothetical material properties revealed that the work-hardening exponent and friction coefficient affect tube deformation. The results of this work explain the influences of material properties on experimentally observed phenomena. Materials with a large work-hardening exponent are less prone to thinning during forming and have a greater forming limit. On the other hand, the larger the friction coefficient between the plug and the mother tube, the larger the deformation in the axial direction was, and then the thickness reduction increased due to biaxial tension.
- 23 August 2023
- Published by Springer Nature
- p. 594-602
Effect of Material on Strain Direction in Tube Expansion Drawing Process
- 23 August 2023
- Published by Springer Nature
- p. 594-602
Effect of Material on Strain Direction in Tube Expansion Drawing Process