Masayoshi Akiyama
Research Subjects
Masayoshi Akiyama has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Shohei Kajikawa
電気通信大学 大学院情報理工学研究科 機械知能システム学専
3 shared publications - Takashi Kuboki
The University of Electro-Communications Department of Mechanical and Intelligent Systems Engineering
3 shared publications - Shiliang Zhang
Department of Mechanical and Intelligent Systems Engineering, The University of Electro-Communications, Tokyo, Japan
2 shared publications - Hikaru Kawaguchi
The University of Electro-Communications
1 shared publication - Isamu Akasaka
Miyazaki Machinery Systems Co., Ltd., 1 Nii, Kaizuka-shi, Osaka 597-8588, Japan
1 shared publication - Yuzo Terashita
Miyazaki Machinery Systems Co., Ltd., 1 Nii, Kaizuka-shi, Osaka 597-8588, Japan
1 shared publication
Latest Publications
- 8 March 2025
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 137 (5-6) , 2743-2759
Effect of plug geometry on forming accuracy in tube expansion drawing process
- 8 March 2025
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 137 (5-6) , 2743-2759
Effect of plug geometry on forming accuracy in tube expansion drawing process
- 21 May 2024
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 146 (7) , 1-36
Influence of Mechanical Properties of Tube on Forming Limits and Deformation Characteristics in an Expansion Drawing Process
This paper describes an efficient method of manufacturing thin-walled metal tubes. The proposed method is an expansion drawing and it consists of two stages, flaring and drawing, during which high thickness reduction is achieved because the tube being processed is subjected to tensile stress in both the circumferential and axial directions. The optimal plug half-angle for various materials is investigated using a finite element analysis and experiments, revealing the plug shape with the highest expansion limit and the highest thickness reduction ratio. To investigate the deformation characteristics of different materials during the expansion drawing process, the strain in tubes formed using different materials was measured experimentally using a square grid on the outer surface of the tubes. In addition, a finite element analysis using hypothetical material properties revealed that the work-hardening exponent and friction coefficient affect tube deformation. The results of this work explain the influences of material properties on experimentally observed phenomena. Materials with a large work-hardening exponent are less prone to thinning during forming and have a greater forming limit. On the other hand, the larger the friction coefficient between the plug and the mother tube, the larger the deformation in the axial direction was, and then the thickness reduction increased due to biaxial tension.
- 21 May 2024
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 146 (7) , 1-36
Influence of Mechanical Properties of Tube on Forming Limits and Deformation Characteristics in an Expansion Drawing Process
This paper describes an efficient method of manufacturing thin-walled metal tubes. The proposed method is an expansion drawing and it consists of two stages, flaring and drawing, during which high thickness reduction is achieved because the tube being processed is subjected to tensile stress in both the circumferential and axial directions. The optimal plug half-angle for various materials is investigated using a finite element analysis and experiments, revealing the plug shape with the highest expansion limit and the highest thickness reduction ratio. To investigate the deformation characteristics of different materials during the expansion drawing process, the strain in tubes formed using different materials was measured experimentally using a square grid on the outer surface of the tubes. In addition, a finite element analysis using hypothetical material properties revealed that the work-hardening exponent and friction coefficient affect tube deformation. The results of this work explain the influences of material properties on experimentally observed phenomena. Materials with a large work-hardening exponent are less prone to thinning during forming and have a greater forming limit. On the other hand, the larger the friction coefficient between the plug and the mother tube, the larger the deformation in the axial direction was, and then the thickness reduction increased due to biaxial tension.
- Open Access
Tube Drawing Process with Diameter Expansion for Effectively Reducing Thickness
The present paper describes a tube drawing method with diameter expansion, which is herein referred to as “expansion drawing”, for effectively producing thin-walled tube. In the proposed method, the tube end is flared by pushing a plug into the tube, and the tube is then expanded by drawing the plug in the axial direction while the flared end is chucked. The forming characteristics and effectiveness of the proposed method were investigated through a series of finite element method (FEM) analyses and experiments. As a result of FEM analysis, the expansion drawing effectively reduced the tube thickness with a smaller axial load when compared with the conventional method. According to the experimental results, the thin-walled tube was produced successfully by the expansion drawing. Maximum thickness reduction ratios for a carbon steel (STKM13C) and an aluminum alloy (AA1070) were 0.15 and 0.29 when the maximum expansion ratios were 0.23 and 0.31, respectively. The above results suggest that the proposed expansion drawing method is effective for producing thin-walled tubes.
Open AccessTube Drawing Process with Diameter Expansion for Effectively Reducing Thickness
The present paper describes a tube drawing method with diameter expansion, which is herein referred to as “expansion drawing”, for effectively producing thin-walled tube. In the proposed method, the tube end is flared by pushing a plug into the tube, and the tube is then expanded by drawing the plug in the axial direction while the flared end is chucked. The forming characteristics and effectiveness of the proposed method were investigated through a series of finite element method (FEM) analyses and experiments. As a result of FEM analysis, the expansion drawing effectively reduced the tube thickness with a smaller axial load when compared with the conventional method. According to the experimental results, the thin-walled tube was produced successfully by the expansion drawing. Maximum thickness reduction ratios for a carbon steel (STKM13C) and an aluminum alloy (AA1070) were 0.15 and 0.29 when the maximum expansion ratios were 0.23 and 0.31, respectively. The above results suggest that the proposed expansion drawing method is effective for producing thin-walled tubes.