JGJiashun Gao

Jiashun Gao

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Jiashun Gao has a total of 44 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Microstructure Evolution and Strength–Toughness Trade-Off in 1Cr12Ni2WMoVNb Martensitic Stainless Steel During Tempering

    by Jiashun Gao, Liehua Liu, Zhilong Xu, Jiang Zhu, Zhijie Hu, Hongxin Lin

    The influence of tempering temperature on the microstructure evolution and mechanical properties of 1Cr12Ni2WMoVNb martensitic stainless steel was systematically investigated in the range of 200–650 °C. Microhardness, tensile strength, and impact toughness were evaluated, combined with analyses using confocal laser scanning microscopy (CLSM), scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy-dispersive spectroscopy (EDS), and phase characterization techniques. The results show that hardness and tensile strength initially decrease, then increase to a peak at approximately 550 °C due to secondary hardening, and finally decline significantly. In contrast, impact toughness exhibits an inverse trend, revealing a clear strength–toughness trade-off. Microstructural analysis indicates that this behavior is governed by the competition among multiple strengthening mechanisms. At intermediate temperatures, the precipitation of fine and dispersed M23C6 carbides leads to strong dislocation pinning and pronounced precipitation strengthening, resulting in peak strength but reduced plastic deformation capability. At higher temperatures, carbide coarsening and dislocation recovery weaken strengthening while restoring plasticity, thereby improving toughness. These findings clarify the temperature-dependent competition among strengthening mechanisms governing the strength–toughness evolution during tempering.

  • Open Access

    Study on the Forming Quality and Controllability of Ultrasonic-Assisted Spinning of V-Grooves

    by Jinyun Lehao, Yilong Xing, Zhenrong Xie, Shiqi Chen, Weiwen Chen, Zejie Li, Jiashun Gao, Zhilong Xu

    Spinning forming is a metal plastic processing technology used to manufacture thin-walled hollow axisymmetric parts. However, during the spinning process, issues such as excessive local loads can induce non-uniform plastic deformation, leading to poor forming quality. In this study, orthogonal experiments were conducted on V-groove specimens made of SPHE steel under different ultrasonic power (with constant static load and spinning passes) and different numbers of spinning passes (with constant static load and ultrasonic power). For each parameter set, three specimens were tested, and finite element analysis using Abaqus.2021 software was performed for verification. The study explored the influence of introducing ultrasonic-assisted spinning during spinning on the forming quality of the V-groove, as well as the effects of controlling ultrasonic power and spinning passes. By combining the ultrasonic-assisted spinning experiments with finite element simulation results, the effects and relative significance of different ultrasonic power and different spinning passes on forming quality were evaluated through analyses of V-groove depth, inclination angle, microhardness, microstructure, and roughness. The results show that ultrasonic-assisted spinning significantly improves the forming depth of the V-groove. Under 50% ultrasonic power, the groove depth increased from 434.54 μm under the reference condition to 598.09 μm. Meanwhile, the groove angle decreased from 63.27° to 60.77°, indicating improvements in groove sharpness and geometric accuracy. When the spinning passes reached 54, the groove depth increased from 299.84 μm to 560.68 μm. The findings demonstrate that ultrasonic power and the spinning passes can effectively regulate the geometric morphology of the V-groove and improve the forming quality in ultrasonic-assisted spinning.

  • Open Access

    Study on the Effect of Laser Shock Angle on Surface Integrity and Wear Performance of H13 Steel

    by Ke Tang, Jiang Zhu, Zejie Li, Shiqi Chen, Yuqiang Zhang, Yunfeng Yan, Qing Hao, Bicheng Guo, Fasheng Zhong, Weiwen Chen, et al.

    The internal surfaces of hot-working dies are prone to wear and fatigue fracture during service, often necessitating surface modification and strengthening. Among available techniques, laser shock peening (LSP) is an effective surface strengthening method. However, when treating internal surfaces, achieving perpendicular laser incidence is difficult, and irradiation must often be applied at an angle. To clarify the relationship between the laser incidence angle and the strengthening effect, this study applied laser shock peening to H13 steel at various incidence angles(0°, 15°, 30°, 45°) with a spot diameter of 3 mm, using laser energies of 8 J, 8.2 J, 9.2 J, and 11.3 J, respectively, and maintaining a fixed power density of 1.41 GW/cm2. By maintaining a consistent power density through laser energy compensation, the influence of the incidence angle on surface integrity and wear resistance of the hole structure was systematically investigated. The results show that as the impact angle increases from 0° to 45°, the depth of the affected material layer gradually decreases. Surface microhardness and residual compressive stress peak at a 30° impact angle, reaching values of 633.5 HV1 and 517.4 Mpa, respectively. Wear tests indicated that the friction coefficient was lowest at 30° (0.542), with the dominant wear mechanism shifting from abrasive to adhesive wear. Under controlled power density conditions, oblique laser impact improves surface properties at the expense of a reduced thickness of the affected layer.


  • Open Access

    Inspection and Modeling Analysis of Locking Pins in the Penultimate-Stage Blades of a 600 MW Steam Turbine

    by Ke Tang, Weiwen Chen, Jiang Zhu, Binhao Yi, Qing Hao, Jiashun Gao, Zhilong Xu, Bicheng Guo, Shiqi Chen

    The fracture behavior of a locking pin used in the penultimate-stage blades of a 600 MW steam turbine in a thermal power plant was investigated through microstructural and microhardness characterization, fracture surface and energy-dispersive spectroscopy (EDS) analysis, as well as finite element load simulation. The microhardness values measured on the cross-section of the service pins ranged from 528 to 541 HV0.1, showing little difference from the unused pins. Scanning electron microscopy analysis revealed that approximately 70% of the fracture surfaces exhibited an intergranular “rock candy” morphology. The results indicate that pin failure was primarily caused by the combined effects of fretting wear and stress corrosion cracking (SCC). Specifically, vibration at the blade root, impeller, and pins due to start–stop cycles and load variations led to fretting wear, forming pits approximately 75 μm in size. Under the combined effects of weakly corrosive wet steam environments and shear stresses, SCC initiated at the high stress concentration points of these pits. Early crack propagation primarily followed original austenite grain boundaries, while later stages mainly extended along martensite plate boundaries. As cracks advanced, the cross-sectional area gradually decreased, causing the effective shear stress to increase until it exceeded the shear strength, ultimately leading to fracture. These findings not only provide a scientific basis for enhancing the reliability of steam turbine locking pins and extending their service life, but also contribute to a broader understanding of the failure mechanisms of key components operating under corrosive and fluctuating load environments.


  • Open Access

    Ultrasonic-Assisted Spinning V-Groove Moulding Mechanism and Accuracy Research

    by Shiqi Chen, Weiqing Wang, Qingshan Jiang, Jiashun Gao, Yongqing Lai, Yuhong Liu, Zhilong Xu, Zhenye Zhao

    Spinning forming, a new method for processing multi-ribbed pulleys, is increasingly replacing traditional casting and cutting techniques. However, reducing the substantial forming load remains a challenging task. This paper explores the introduction of ultrasonic assistance into the spinning process to examine the V-groove formation in multi-ribbed pulleys and combines experimental spinning trials with finite element analysis (FEA) to investigate the process. It assesses how ultrasonic aid affects spinning quality under various static loads by analysing V-groove depth, inclination angle, microhardness, structure, and surface roughness. The results indicate that ultrasonic assistance significantly increases the depth of the V-groove in spinning formation. Initially, the V-groove depth is 197.64 μm, which improves to 410.35 μm with ultrasonic aid, corresponding to a reduction in static load by 185 N. The V-groove angle rises with static load, but with ultrasonic assistance, the angle stabilises, enhancing forming accuracy. At a static load of 700 N, the V-groove angle decreases from 74.32° to 62.96°.


  • Open Access

    Mechanisms of Hardness Variation in 14Cr12Ni3Mo2VN Martensitic Stainless Steel Under Different Tempering Temperatures Following High-Frequency Induction Quenching

    by Jiashun Gao, Haoxin Lan, Qingshan Jiang, Shiqi Chen, Zhilong Xu, Yunchang Yu, Xiaolei Du, Lize Cai

    To investigate the effect of tempering temperature on the hardness and its underlying mechanisms in 14Cr12Ni3Mo2VN martensitic stainless steel after high-frequency induction quenching (HFIQ), the microstructure, energy-dispersive spectroscopy (EDS) of precipitated particles, residual austenite, residual stress, and microhardness of the material tempered at different temperatures were examined and analyzed. The results reveal that a secondary hardening phenomenon occurs during the tempering process in 14Cr12Ni3Mo2VN martensitic stainless steel. Overall, with increasing tempering temperature, the microhardness initially decreases slightly, then rises to a secondary hardening peak, and finally drops rapidly. The secondary hardening peak corresponds to a tempering temperature of approximately 440 °C, with a microhardness of about 483 HV0.1. The secondary hardening phenomenon is likely attributed to the dispersion strengthening caused by the precipitation of alloy carbides during tempering. The precipitation and coarsening of carbides reduce lattice distortion and solid solution strengthening, while the release of residual stress diminishes stress-induced strengthening. Additionally, the decomposition of the martensitic structure leads to the formation of ferrite and carbides. The combined effects of these factors result in a decrease in hardness.


  • Open Access

    Study on Microstructure and Corrosion Fatigue Resistance of 14Cr12Ni3Mo2VN Materials Based on the Composite Technology of High-Frequency Induction Quenching and Laser Shock Peening

    by Jiashun Gao, Zhilong Xu, Huiting Lv, Zhiling Yang, Guang Yang, Liehua Liu

    This study investigated the microstructure, microhardness, and residual compressive stress of 14Cr12Ni3Mo2VN martensitic stainless steel treated with high-frequency induction quenching (HFIQ) and laser shock peening (LSP). Using rotating bending corrosion fatigue testing, the corrosion fatigue performance was analyzed. Results show that a microstructural gradient formed after HFIQ and LSP: the surface layer consisted of nanocrystals, the subsurface layer of short lath martensite, and the core of thick lath martensite. A hardness gradient was introduced, with surface hardness reaching 524 Hv0.1, 163 Hv0.1 higher than the core hardness. A residual compressive stress field was introduced near the surface, with a maximum residual compressive stress of approximately −575 MPa at a depth of 0.1 mm. Corrosion fatigue results indicate that cycle loading times of samples treated with HFIQ and LSP were 2.88, 2.04, and 1.45 times higher than untreated, HFIQ-only, and LSP-only samples, respectively. Transmission electron microscopy (TEM) characterization showed that HFIQ reduced the lath martensite size, while the ultra-high strain rate induced by LSP likely caused dynamic recrystallization, forming numerous sub-boundaries and refining grains, which increased surface hardness. The plastic strain induced by LSP introduced residual compressive stress, counteracting tensile stress and hindering the initiation and propagation of corrosion fatigue cracks.


  • Open Access

    Longitudinal Ultrasonic Vibration-Assisted Planing Method for Processing Micro-Pyramid Arrays

    by Jiashun Gao, Zhilong Xu, Bicheng Guo, Yu Lei, Guang Yang

    Micro-pyramid copper molds are critical components in the preparation of high-precision optical elements, such as light-trapping films and reflective films. Their surfaces are composed of micro-pyramid arrays (MPAs). The surface roughness and edge burrs of MPAs seriously affect the optical properties of optical elements. To reduce the surface roughness, as well as the sizes of the edge burrs, the longitudinal ultrasonic vibration-assisted planing (LUVP) method for processing MPAs was developed during this study. In addition, an experiment was conducted to compare the precision planing and LUVP methods of MPA generation. The results show that the tool nose amplitude of the LUVP experimental platform constructed during this study was 3.3 μm, and that the operating frequency was 19.85 kHz. An MPA processed by LUVP had a smaller surface roughness than that of an MPA produced by precision planing; it also had fewer and smaller edge burrs, and there was slightly less diamond tool wear. The MPA cut using the LUVP method had no corrugation on its surface. This research lays a foundation for developing higher-precision micro-pyramid plastic films.


  • Open Access

    Research on Micro-Triangular Pyramid Array-Based Fly-Cutting Technology Using the Orthogonal Test Method

    by Jiashun Gao, Yu Lei, Zhilong Xu

    The copper mold of the micro-triangular pyramid (MTP) is a key component of MTP plastic film manufacturing, and its optical functional surface comprises micro-triangular pyramid arrays (MTPAs). The edge burrs of MTPAs severely affect the optical properties of MTP plastic film. To solve the problem of excessive edge burr of MTPA machining using the fly-cutting method, the orthogonal experimental method was used to optimize the four influencing factors: fly-cutting speed, feed speed, cutting depth, and cooling mode. The results show that the impact of these influencing factors on surface roughness, the projected area of the exit edge burr, and exit edge burr thickness are ranked from largest to the smallest as follows: fly-cutting speed, feed speed, cutting depth, and cooling mode. The factors affecting tool nose wear in descending order are fly-cutting speed, feed speed, cooling mode, and cutting depth. The optimal conditions for minimizing the thickness of the edge burr were a fly-cutting speed of 7.85 m/s, a feed speed of 50 mm/min, a finishing cutting depth of 15 μm, and using compressed air with oil mist for cooling. This study lays a foundation for improving the anti-reflection performance of MTP plastic film.


  • Open Access

    Fly-Cutting Processing of Micro-Triangular Pyramid Arrays and Synchronous Micro-Scrap Removal

    by Jiashun Gao, Zhilong Xu, Yu Lei, Su Huang

    Many micro-scraps are generated when a micro-triangular pyramid array (MTPA) is machined by the fly-cutting method. Micro-scraps are generally not removed quickly enough; therefore, these residual micro-scraps participate in the cutting process again, scratching the workpiece surface and accelerating diamond tool wear. To remove micro-scraps rapidly, a fly-cutting method to produce MTPAs on vertically oriented working surfaces was developed during this study. The results show that an MTPA produced by fly cutting on a vertical workpiece had a clearly outlined structure, high dimensional accuracy, and a low surface roughness. There was no micro-scrap residue on the workpiece surface and the diamond tool wear was small. The cutting inlet edges had no burrs, and the cutting outlet edges had only a small number of burrs. This method of fly cutting MTPAs on vertically oriented working surfaces provides a foundation for the development of high-precision micro-triangular pyramid optical elements.