Kinga Majkowycz
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Kinga Majkowycz has a total of 43 co-authors. Here are the top co-authors by number of shared publications:
- Piotr Martyniuk
Institute of Applied Physics, Military University of Technology, 2 Kaliskiego St., 00-908 Warsaw, Poland
14 shared publications - Krzysztof Murawski
Institute of Applied Physics, Military University of Technology, Warsaw, Poland
9 shared publications - Małgorzata Kopytko
Military University of Technology
8 shared publications - Tetiana Manyk
Institute of Applied Physics, Military University of Technology, ul. Kaliskiego 2, 00-908 Warsaw, Poland
5 shared publications - Jaroslaw Rutkowski
Institute of Applied Physics, Military University of Technology, Warsaw, Poland
3 shared publications - Waldemar Gawron
Institute of Applied Physics, Military University of Technology, 2 Kaliskiego St., 00-908 Warsaw, Poland
3 shared publications
Latest Publications
- Open Access
- 23 July 2026
- Published by IOP Publishing in Nanotechnology
- Vol. 37 (29) , 295202
Deep‐level defects and their optoelectronic impact in 2D wse 2 heterostructures
Understanding and controlling native point defects (NPDs) in two-dimensional (2D) transition metal dichalcogenides (TMDs) is essential for optimizing their electronic and optoelectronic functionality. The paper presents an analysis of NPD occurring WSe 2, deposited on a Si/SiO 2 substrate by the exfoliation method. Deep level transient spectroscopy (DLTS) was employed to quantify electrically active defect levels and to identify dominant NPDs in few-layer WSe 2 . The DLTS spectra revealed the presence of two characteristic deep-level traps, which based on their activation energies and capture cross sections were attributed to selenium vacancies ( V Se ) and selenium antisites ( S e W ). Complementary optical characterization techniques, including photoluminescence and Raman spectroscopy, further confirmed the structural perturbations associated with these NPDs. To establish the impact of the extracted defect states on charge transport, the experimental results were correlated with theoretically simulated current–voltage (I - V) characteristics. The simulations reproduced the experimentally observed non-ideal electrical behavior, highlighting the role of V Se and S e W centers as efficient non-radiative recombination channels and scattering sites. The combined analysis of the electrical, optical, and simulation results offers a coherent view of how NPDs form in exfoliated WSe 2 and clarifies their influence on device-relevant charge-transport mechanisms. These results contribute to a deeper understanding of defect physics in 2D TMD materials and offer valuable guidelines for improving the performance of WSe 2 ‐ based electronic and optoelectronic devices.
- 23 July 2026
- Published by IOP Publishing in Nanotechnology
- Vol. 37 (29) , 295202
Open AccessDeep‐level defects and their optoelectronic impact in 2D wse 2 heterostructures
Understanding and controlling native point defects (NPDs) in two-dimensional (2D) transition metal dichalcogenides (TMDs) is essential for optimizing their electronic and optoelectronic functionality. The paper presents an analysis of NPD occurring WSe 2, deposited on a Si/SiO 2 substrate by the exfoliation method. Deep level transient spectroscopy (DLTS) was employed to quantify electrically active defect levels and to identify dominant NPDs in few-layer WSe 2 . The DLTS spectra revealed the presence of two characteristic deep-level traps, which based on their activation energies and capture cross sections were attributed to selenium vacancies ( V Se ) and selenium antisites ( S e W ). Complementary optical characterization techniques, including photoluminescence and Raman spectroscopy, further confirmed the structural perturbations associated with these NPDs. To establish the impact of the extracted defect states on charge transport, the experimental results were correlated with theoretically simulated current–voltage (I - V) characteristics. The simulations reproduced the experimentally observed non-ideal electrical behavior, highlighting the role of V Se and S e W centers as efficient non-radiative recombination channels and scattering sites. The combined analysis of the electrical, optical, and simulation results offers a coherent view of how NPDs form in exfoliated WSe 2 and clarifies their influence on device-relevant charge-transport mechanisms. These results contribute to a deeper understanding of defect physics in 2D TMD materials and offer valuable guidelines for improving the performance of WSe 2 ‐ based electronic and optoelectronic devices.
- 12 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (4) , 2005-2015
Passivation of AlGaSb/InGaAsSb/GaSb SWIR Detectors by Aqueous (NH 4 ) 2 S Solution, SiO 2 , and Ionic Liquid Encapsulation
We report on the development of a passivation technology for InGaAsSb nBp photodiodes incorporating an AlGaSb barrier, aimed at achieving bulk-limited leakage currents and enhanced detectivity in detectors with a photosensitive area of 0.01mm2. Following passivation with SiO2 preceded by sulfidation, an increased yield of 113- $\mu $ m-diameter diodes exhibiting improved zero-bias resistance ( ${R}_{{0}}\text {)}$ was observed, particularly at lower temperatures reachable with thermoelectric coolers. At 215K, the dark current of devices of this size, with ${R}_{{0}}$ close to the average, was reduced by two orders of magnitude. At this temperature, the volume and surface generation rates of carriers were found to be equal for diodes with an average size of $150~\mu $ m. Furthermore, we investigated alternative approaches, including backside illumination through the GaSb substrate, the integration with immersion optics, and the use of ionic liquid (IL)-based passivation technique.
- 12 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (4) , 2005-2015
Passivation of AlGaSb/InGaAsSb/GaSb SWIR Detectors by Aqueous (NH 4 ) 2 S Solution, SiO 2 , and Ionic Liquid Encapsulation
We report on the development of a passivation technology for InGaAsSb nBp photodiodes incorporating an AlGaSb barrier, aimed at achieving bulk-limited leakage currents and enhanced detectivity in detectors with a photosensitive area of 0.01mm2. Following passivation with SiO2 preceded by sulfidation, an increased yield of 113- $\mu $ m-diameter diodes exhibiting improved zero-bias resistance ( ${R}_{{0}}\text {)}$ was observed, particularly at lower temperatures reachable with thermoelectric coolers. At 215K, the dark current of devices of this size, with ${R}_{{0}}$ close to the average, was reduced by two orders of magnitude. At this temperature, the volume and surface generation rates of carriers were found to be equal for diodes with an average size of $150~\mu $ m. Furthermore, we investigated alternative approaches, including backside illumination through the GaSb substrate, the integration with immersion optics, and the use of ionic liquid (IL)-based passivation technique.
- Open Access
- 12 September 2025
- Published by MDPI AG in Proceedings
- Vol. 129 (1) , 72
Theoretical Analysis of Low-Threshold Avalanche Effect in WSe2 Stepwise van-der-Waals Homojunction Photodiodes
In this work, we report simulation-assisted analysis of a room-temperature (300 K) low-threshold avalanche photodiode (APD) based on a WSe2 homojunction. Device simulations were conducted using a two-band model and the Chynoweth formalism for impact ionization, with material parameters extracted for few-layer and multi-layer homojunction WSe2 structures. The simulated results accurately reproduce experimental dark and photocurrent characteristics, with an avalanche threshold voltage of approximately ~1.6 V-over 26 times lower than that of conventional InGaAs APDs. The structure exhibits ultra-low dark current (10–100 fA) and high sensitivity, enabling detection of optical signals as low as 7.7 × 104 photons. The analyzed low voltage avalanche photodetector enables utilization in a wide range of applications.
- 12 September 2025
- Published by MDPI AG in Proceedings
- Vol. 129 (1) , 72
Open AccessTheoretical Analysis of Low-Threshold Avalanche Effect in WSe2 Stepwise van-der-Waals Homojunction Photodiodes
In this work, we report simulation-assisted analysis of a room-temperature (300 K) low-threshold avalanche photodiode (APD) based on a WSe2 homojunction. Device simulations were conducted using a two-band model and the Chynoweth formalism for impact ionization, with material parameters extracted for few-layer and multi-layer homojunction WSe2 structures. The simulated results accurately reproduce experimental dark and photocurrent characteristics, with an avalanche threshold voltage of approximately ~1.6 V-over 26 times lower than that of conventional InGaAs APDs. The structure exhibits ultra-low dark current (10–100 fA) and high sensitivity, enabling detection of optical signals as low as 7.7 × 104 photons. The analyzed low voltage avalanche photodetector enables utilization in a wide range of applications.
- Open Access
- 12 September 2025
- Published by MDPI AG in Proceedings
- Vol. 129 (1) , 69
LWIR Interband Cascade Photodetectors with InAs/InAsSb II Type Superlattice Absorber
The properties of long-wave infrared (LWIR) interband cascade photodetectors (ICIPs) with type II superlattices (T2SLs) and gallium-free (Ga-free) InAs/InAsSb absorbers were determined using photoluminescence (PL) and spectral response (SR) measurements. The heterostructures were grown by molecular beam epitaxy (MBE) on a GaAs substrate. Three structures with different numbers of stages were compared. The structures were optimized for 10.7 μm at 300 K. Moreover, theoretical calculations were performed using APSYS to compare with the experimental results. The PL results provided information on transitions from minibands and intragap states in the studied structures. SR measurements helped isolate transitions involving minibands, which facilitated the analysis of visible transitions in the PL spectra, where point defect (NPD) transitions were also observed.
- 12 September 2025
- Published by MDPI AG in Proceedings
- Vol. 129 (1) , 69
Open AccessLWIR Interband Cascade Photodetectors with InAs/InAsSb II Type Superlattice Absorber
The properties of long-wave infrared (LWIR) interband cascade photodetectors (ICIPs) with type II superlattices (T2SLs) and gallium-free (Ga-free) InAs/InAsSb absorbers were determined using photoluminescence (PL) and spectral response (SR) measurements. The heterostructures were grown by molecular beam epitaxy (MBE) on a GaAs substrate. Three structures with different numbers of stages were compared. The structures were optimized for 10.7 μm at 300 K. Moreover, theoretical calculations were performed using APSYS to compare with the experimental results. The PL results provided information on transitions from minibands and intragap states in the studied structures. SR measurements helped isolate transitions involving minibands, which facilitated the analysis of visible transitions in the PL spectra, where point defect (NPD) transitions were also observed.
- Open Access
- 12 September 2025
- Published by MDPI AG in Proceedings
- Vol. 129 (1) , 13
Passivation of MWIR Heterostructure p-InAsSbP/n-InAs Photodiodes Using SiO2 Layers for Near-Room-Temperature Operation
We examined the effect of SiO2 passivation on the parameters of mesa heterostructure InAs/InAsSbP photodiodes with a spectral responsivity 50% cut off at 3.5 µm at 295 K, specific to the InAs absorber layer. The R0A product was found to increase by 30% after passivation of the devices of 113 µm in diameter, up to 0.9 Ωcm2, while for those with a diameter of 1.13 mm, R0A of 2.2 Ωcm2 was achieved, with a value of D* > 3 × 109 cmHz1/2/W at the peak of the spectrum, 1 kHz, 0 V bias, 295 K. To the best of our knowledge, this is the highest R0A value at room temperature reported to date for a photodiode with an InAs absorber.
- 12 September 2025
- Published by MDPI AG in Proceedings
- Vol. 129 (1) , 13
Open AccessPassivation of MWIR Heterostructure p-InAsSbP/n-InAs Photodiodes Using SiO2 Layers for Near-Room-Temperature Operation
We examined the effect of SiO2 passivation on the parameters of mesa heterostructure InAs/InAsSbP photodiodes with a spectral responsivity 50% cut off at 3.5 µm at 295 K, specific to the InAs absorber layer. The R0A product was found to increase by 30% after passivation of the devices of 113 µm in diameter, up to 0.9 Ωcm2, while for those with a diameter of 1.13 mm, R0A of 2.2 Ωcm2 was achieved, with a value of D* > 3 × 109 cmHz1/2/W at the peak of the spectrum, 1 kHz, 0 V bias, 295 K. To the best of our knowledge, this is the highest R0A value at room temperature reported to date for a photodiode with an InAs absorber.
- Open Access
- 21 May 2025
- Published by Optica Publishing Group in Optics Express
- Vol. 33 (11) , 22563-22569
Defect levels in InAs/InAsSb type-II superlattice for LWIR cascade detectors
This work presents DLTS (deep level transient spectroscopy) and PL (photoluminescence) results for a longwave infrared (LWIR) type-II InAs/InAsSb superlattice (T2SLs) based cascade detectors grown by a RIBER Compact 21-DZ solid source molecular beam epitaxy (MBE) system on GaAs substrate. The absorber was optimized for 10.6 μm at 300 K. In order to verify defects from individual heterostructure layers, DLTS measurements were performed for the entire cascade structure and a single cell (stage) of the cascade detector. The obtained results indicate that there are three defect levels (NDPs- native point defects) located in the absorber layer and one related to the occurrence of mismatch dislocations between buffer and substrate.
- 21 May 2025
- Published by Optica Publishing Group in Optics Express
- Vol. 33 (11) , 22563-22569
Open AccessDefect levels in InAs/InAsSb type-II superlattice for LWIR cascade detectors
This work presents DLTS (deep level transient spectroscopy) and PL (photoluminescence) results for a longwave infrared (LWIR) type-II InAs/InAsSb superlattice (T2SLs) based cascade detectors grown by a RIBER Compact 21-DZ solid source molecular beam epitaxy (MBE) system on GaAs substrate. The absorber was optimized for 10.6 μm at 300 K. In order to verify defects from individual heterostructure layers, DLTS measurements were performed for the entire cascade structure and a single cell (stage) of the cascade detector. The obtained results indicate that there are three defect levels (NDPs- native point defects) located in the absorber layer and one related to the occurrence of mismatch dislocations between buffer and substrate.
- Open Access
- 24 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 13, 390-395
Analysis of InAs/InAsSb Superlattice Miniband Positions for a Cascade LWIR Detector
The paper presents an analysis of the miniband transitions of long-infrared (LWIR) interband cascade photodetectors (ICIP), with type-II superlattices (T2SLs), gallium-free (gGa-freeh) InAs/InAsSb (xSb = 0.39) absorber, grown by molecular beam epitaxy (MBE) on a GaAs (001) substrate. The results collected based on the photoluminescence (PL) and spectral response (SR) measurements were combined with theoretical calculations using the (8 × 8 Hamiltonian) kmodel for both strained and strain-free structure. The temperature dependence of HH1C1, LH1C1, SOC1 and HH2C1 was determined. Their respective 300 K energies were 114 meV, 195 meV, 290 meV and 380 meV, respectively. Moreover, the Varshni parameters were determined. For the PL results, 85 meV was observed across the entire temperature range. Remarkably, at cryogenic temperatures additional blue-shifted 5 meV and 14 meV transitions within the energy gap (Eg) occurred, respectively.
- 24 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 13, 390-395
Open AccessAnalysis of InAs/InAsSb Superlattice Miniband Positions for a Cascade LWIR Detector
The paper presents an analysis of the miniband transitions of long-infrared (LWIR) interband cascade photodetectors (ICIP), with type-II superlattices (T2SLs), gallium-free (gGa-freeh) InAs/InAsSb (xSb = 0.39) absorber, grown by molecular beam epitaxy (MBE) on a GaAs (001) substrate. The results collected based on the photoluminescence (PL) and spectral response (SR) measurements were combined with theoretical calculations using the (8 × 8 Hamiltonian) kmodel for both strained and strain-free structure. The temperature dependence of HH1C1, LH1C1, SOC1 and HH2C1 was determined. Their respective 300 K energies were 114 meV, 195 meV, 290 meV and 380 meV, respectively. Moreover, the Varshni parameters were determined. For the PL results, 85 meV was observed across the entire temperature range. Remarkably, at cryogenic temperatures additional blue-shifted 5 meV and 14 meV transitions within the energy gap (Eg) occurred, respectively.
- 25 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 46 (2) , 155-158
Photocurrent-Induced 1/f Noise in AIIIBV T2SLs Infrared Detectors
This letter focuses on the 1/f noise induced by a photocurrent in infrared (IR) detectors based on the AIIIBV InAs/GaSb, and InAs/InAsSb type-II superlattices (T2SLs) optimized for mid-, or long-wavelength range. The relative photocurrent 1/f noise αph≈3×10-11 and αph≈7×10-11 were found for detectors based on InAs/GaSb and InAs/InAsSb T2SLs, respectively. It was shown that the dark current generates 1/f noise much more efficiently than the photocurrent in all detectors. The lowest relative dark current 1/f noise αd≈4×10-8 was obtained for interband cascade InAs/InAsSb T2SL detectors. The correlation between the photocurrent and the dark current 1/f noises was extracted, suggesting that both components partially origin the same source.
- 25 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 46 (2) , 155-158
Photocurrent-Induced 1/f Noise in AIIIBV T2SLs Infrared Detectors
This letter focuses on the 1/f noise induced by a photocurrent in infrared (IR) detectors based on the AIIIBV InAs/GaSb, and InAs/InAsSb type-II superlattices (T2SLs) optimized for mid-, or long-wavelength range. The relative photocurrent 1/f noise αph≈3×10-11 and αph≈7×10-11 were found for detectors based on InAs/GaSb and InAs/InAsSb T2SLs, respectively. It was shown that the dark current generates 1/f noise much more efficiently than the photocurrent in all detectors. The lowest relative dark current 1/f noise αd≈4×10-8 was obtained for interband cascade InAs/InAsSb T2SL detectors. The correlation between the photocurrent and the dark current 1/f noises was extracted, suggesting that both components partially origin the same source.
- Open Access
- 9 October 2024
- Published by MDPI AG in Nanomaterials
- Vol. 14 (19) , 1612
The Influence of Etching Method on the Occurrence of Defect Levels in III-V and II-VI Materials
The influence of the etching method on the occurrence of defect levels in InAs/InAsSb type-II superlattice (T2SLs) and MCT photodiode is presented. For both analyzed detectors, the etching process was performed by two methods: wet chemical etching and dry etching using an ion beam (RIE—reactive ion etching). The deep-level transient spectroscopy (DLTS) method was used to determine the defect levels occurring in the analyzed structures. The obtained results indicate that the choice of etching method affects the occurrence of additional defect levels in the MCT material, but it has no significance for InAs/InAsSb T2SLs.
- 9 October 2024
- Published by MDPI AG in Nanomaterials
- Vol. 14 (19) , 1612
Open AccessThe Influence of Etching Method on the Occurrence of Defect Levels in III-V and II-VI Materials
The influence of the etching method on the occurrence of defect levels in InAs/InAsSb type-II superlattice (T2SLs) and MCT photodiode is presented. For both analyzed detectors, the etching process was performed by two methods: wet chemical etching and dry etching using an ion beam (RIE—reactive ion etching). The deep-level transient spectroscopy (DLTS) method was used to determine the defect levels occurring in the analyzed structures. The obtained results indicate that the choice of etching method affects the occurrence of additional defect levels in the MCT material, but it has no significance for InAs/InAsSb T2SLs.
- Open Access
- 26 August 2024
- Published by MDPI AG in Nanomaterials
- Vol. 14 (17) , 1393
Optical Characterization of the Interband Cascade LWIR Detectors with Type-II InAs/InAsSb Superlattice Absorber
The long-wave infrared (LWIR) interband cascade detector with type-II superlattices (T2SLs) and a gallium-free (“Ga-free”) InAs/InAsSb (x = 0.39) absorber was characterized by photoluminescence (PL) and spectral response (SR) methods. Heterostructures were grown by molecular beam epitaxy (MBE) on a GaAs substrate (001) orientation. The crystallographic quality was confirmed by high-resolution X-Ray diffraction (HRXRD). Two independent methods, combined with theoretical calculations, were able to determine the transitions between the superlattice minibands. Moreover, transitions from the trap states were determined. Studies of the PL intensity as a function of the excitation laser power allowed the identification of optical transitions. The determined effective energy gap (Eg) of the tested absorber layer was 116 meV at 300 K. The transition from the first light hole miniband to the first electron miniband was red-shifted by 76 meV. The detected defects’ energy states were constant versus temperature. Their values were 85 meV and 112 meV, respectively. Moreover, two additional transitions from acceptor levels in cryogenic temperature were determined by being shifted from blue to Eg by 6 meV and 16 meV, respectively.
- 26 August 2024
- Published by MDPI AG in Nanomaterials
- Vol. 14 (17) , 1393
Open AccessOptical Characterization of the Interband Cascade LWIR Detectors with Type-II InAs/InAsSb Superlattice Absorber
The long-wave infrared (LWIR) interband cascade detector with type-II superlattices (T2SLs) and a gallium-free (“Ga-free”) InAs/InAsSb (x = 0.39) absorber was characterized by photoluminescence (PL) and spectral response (SR) methods. Heterostructures were grown by molecular beam epitaxy (MBE) on a GaAs substrate (001) orientation. The crystallographic quality was confirmed by high-resolution X-Ray diffraction (HRXRD). Two independent methods, combined with theoretical calculations, were able to determine the transitions between the superlattice minibands. Moreover, transitions from the trap states were determined. Studies of the PL intensity as a function of the excitation laser power allowed the identification of optical transitions. The determined effective energy gap (Eg) of the tested absorber layer was 116 meV at 300 K. The transition from the first light hole miniband to the first electron miniband was red-shifted by 76 meV. The detected defects’ energy states were constant versus temperature. Their values were 85 meV and 112 meV, respectively. Moreover, two additional transitions from acceptor levels in cryogenic temperature were determined by being shifted from blue to Eg by 6 meV and 16 meV, respectively.