Tetiana Manyk
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Tetiana Manyk has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
- Jaroslaw Rutkowski
Institute of Applied Physics, Military University of Technology, Warsaw, Poland
20 shared publications - Piotr Martyniuk
Institute of Applied Physics, Military University of Technology, 2 Kaliskiego St., 00-908 Warsaw, Poland
19 shared publications - Małgorzata Kopytko
Military University of Technology
8 shared publications - Kinga Majkowycz
Institute of Applied Physics, Military University of Technology, Warsaw, Poland
5 shared publications - Krzysztof Murawski
Institute of Applied Physics, Military University of Technology, Warsaw, Poland
5 shared publications - Krystian Michalczewski
VIGO PHOTONICS S.A., 129/133 Poznańska St., 05-850 Ożarów Mazowiecki, Poland
4 shared publications
Latest Publications
- Open Access
- 12 September 2025
- Published by MDPI AG in Proceedings
- Vol. 129 (1) , 69
LWIR Interband Cascade Photodetectors with InAs/InAsSb II Type Superlattice Absorber
The properties of long-wave infrared (LWIR) interband cascade photodetectors (ICIPs) with type II superlattices (T2SLs) and gallium-free (Ga-free) InAs/InAsSb absorbers were determined using photoluminescence (PL) and spectral response (SR) measurements. The heterostructures were grown by molecular beam epitaxy (MBE) on a GaAs substrate. Three structures with different numbers of stages were compared. The structures were optimized for 10.7 μm at 300 K. Moreover, theoretical calculations were performed using APSYS to compare with the experimental results. The PL results provided information on transitions from minibands and intragap states in the studied structures. SR measurements helped isolate transitions involving minibands, which facilitated the analysis of visible transitions in the PL spectra, where point defect (NPD) transitions were also observed.
- 12 September 2025
- Published by MDPI AG in Proceedings
- Vol. 129 (1) , 69
Open AccessLWIR Interband Cascade Photodetectors with InAs/InAsSb II Type Superlattice Absorber
The properties of long-wave infrared (LWIR) interband cascade photodetectors (ICIPs) with type II superlattices (T2SLs) and gallium-free (Ga-free) InAs/InAsSb absorbers were determined using photoluminescence (PL) and spectral response (SR) measurements. The heterostructures were grown by molecular beam epitaxy (MBE) on a GaAs substrate. Three structures with different numbers of stages were compared. The structures were optimized for 10.7 μm at 300 K. Moreover, theoretical calculations were performed using APSYS to compare with the experimental results. The PL results provided information on transitions from minibands and intragap states in the studied structures. SR measurements helped isolate transitions involving minibands, which facilitated the analysis of visible transitions in the PL spectra, where point defect (NPD) transitions were also observed.
- Open Access
- 12 September 2025
- Published by MDPI AG in Proceedings
- Vol. 129 (1) , 13
Passivation of MWIR Heterostructure p-InAsSbP/n-InAs Photodiodes Using SiO2 Layers for Near-Room-Temperature Operation
We examined the effect of SiO2 passivation on the parameters of mesa heterostructure InAs/InAsSbP photodiodes with a spectral responsivity 50% cut off at 3.5 µm at 295 K, specific to the InAs absorber layer. The R0A product was found to increase by 30% after passivation of the devices of 113 µm in diameter, up to 0.9 Ωcm2, while for those with a diameter of 1.13 mm, R0A of 2.2 Ωcm2 was achieved, with a value of D* > 3 × 109 cmHz1/2/W at the peak of the spectrum, 1 kHz, 0 V bias, 295 K. To the best of our knowledge, this is the highest R0A value at room temperature reported to date for a photodiode with an InAs absorber.
- 12 September 2025
- Published by MDPI AG in Proceedings
- Vol. 129 (1) , 13
Open AccessPassivation of MWIR Heterostructure p-InAsSbP/n-InAs Photodiodes Using SiO2 Layers for Near-Room-Temperature Operation
We examined the effect of SiO2 passivation on the parameters of mesa heterostructure InAs/InAsSbP photodiodes with a spectral responsivity 50% cut off at 3.5 µm at 295 K, specific to the InAs absorber layer. The R0A product was found to increase by 30% after passivation of the devices of 113 µm in diameter, up to 0.9 Ωcm2, while for those with a diameter of 1.13 mm, R0A of 2.2 Ωcm2 was achieved, with a value of D* > 3 × 109 cmHz1/2/W at the peak of the spectrum, 1 kHz, 0 V bias, 295 K. To the best of our knowledge, this is the highest R0A value at room temperature reported to date for a photodiode with an InAs absorber.
- Open Access
- 8 September 2025
- Published by Polish Academy of Sciences Chancellery in Opto-Electronics Review
- p. 155676
Influence of the multiplication layer on the long-wavelength InAsSb avalanche photodiodes performance
The paper analyses the performance of avalanche barrier infrared detectors based on the bulk InAsSb ternary compound of AIII-BV materials, lattice-matched to the GaSb substrate for a long-wavelength range operating at thermoelectric cooling conditions. A ternary Al0.2As0.8Sb barrier was assumed. Particular attention was paid to the influence of avalanche multiplication layer parameters on the device current-voltage characteristics and current gain. Numerical simulations were performed using a SimuApsys software for the npBp InAsSb detector operating at the temperature achieved by a two-stage thermoelectric cooler (TE), T = 230 K. Based on the analysis of the literature data of the avalanche ionisation coefficient and the density of the band-to-band tunnelling currents, the conditions in which the Zener effect does not reduce the multiplication process were determined. The highest gain can be achieved with a low level of multiplication layer doping and a lower molar composition of antimony compared to the absorber composition (larger band gap energy). The gain also increases with the multiplication of layer thickness. The paper discusses the design of the long-wavelength avalanche detectors based on InAsSb with an optimised multiplication process.
- 8 September 2025
- Published by Polish Academy of Sciences Chancellery in Opto-Electronics Review
- p. 155676
Open AccessInfluence of the multiplication layer on the long-wavelength InAsSb avalanche photodiodes performance
The paper analyses the performance of avalanche barrier infrared detectors based on the bulk InAsSb ternary compound of AIII-BV materials, lattice-matched to the GaSb substrate for a long-wavelength range operating at thermoelectric cooling conditions. A ternary Al0.2As0.8Sb barrier was assumed. Particular attention was paid to the influence of avalanche multiplication layer parameters on the device current-voltage characteristics and current gain. Numerical simulations were performed using a SimuApsys software for the npBp InAsSb detector operating at the temperature achieved by a two-stage thermoelectric cooler (TE), T = 230 K. Based on the analysis of the literature data of the avalanche ionisation coefficient and the density of the band-to-band tunnelling currents, the conditions in which the Zener effect does not reduce the multiplication process were determined. The highest gain can be achieved with a low level of multiplication layer doping and a lower molar composition of antimony compared to the absorber composition (larger band gap energy). The gain also increases with the multiplication of layer thickness. The paper discusses the design of the long-wavelength avalanche detectors based on InAsSb with an optimised multiplication process.
- Open Access
Effect of Multiplication and Charge Layers on the Gain in InGaAsSb/AlGaAs Avalanche Photodiodes at Room Temperature
This paper presents a theoretical analysis of npBp infrared (IR) barrier avalanche photodiode (APD) performance operating at 300 K based on a quaternary compound made of AIIIBV—InGaAsSb, lattice-matched to the GaSb substrate with a p-type barrier made of a ternary compound AlGaSb. Impact ionization in the multiplication layer of InGaAsSb separate absorption, grading, charge, and multiplication avalanche photodiodes (SAGCM APDs) was studied using the Crosslight Software simulation package APSYS. The band structure of the avalanche detector and the electric field distribution for the multiplication and absorption layers were determined. The influence of the multiplication and charge layer parameters on the impact multiplication gain and the excess noise factor was analyzed. It has been shown that with the decrease in the charge layer doping level, the gain and the breakdown voltage increase, but the punch-through voltage decreases, and the linear range of the APD operating voltages widens. The multiplication layer doping level slightly affects the detector parameters, while increasing its width, the photocurrent and the breakdown voltage also increase. The detector structure proposed in this work allows us to obtain a comparable gain and lower dark currents to the APD detectors made of InGaAsSb previously presented in the literature. The performed simulations confirmed the possibility of obtaining APDs with high performance at room temperatures made of InGaAsSb for the SWIR range.
Open AccessEffect of Multiplication and Charge Layers on the Gain in InGaAsSb/AlGaAs Avalanche Photodiodes at Room Temperature
This paper presents a theoretical analysis of npBp infrared (IR) barrier avalanche photodiode (APD) performance operating at 300 K based on a quaternary compound made of AIIIBV—InGaAsSb, lattice-matched to the GaSb substrate with a p-type barrier made of a ternary compound AlGaSb. Impact ionization in the multiplication layer of InGaAsSb separate absorption, grading, charge, and multiplication avalanche photodiodes (SAGCM APDs) was studied using the Crosslight Software simulation package APSYS. The band structure of the avalanche detector and the electric field distribution for the multiplication and absorption layers were determined. The influence of the multiplication and charge layer parameters on the impact multiplication gain and the excess noise factor was analyzed. It has been shown that with the decrease in the charge layer doping level, the gain and the breakdown voltage increase, but the punch-through voltage decreases, and the linear range of the APD operating voltages widens. The multiplication layer doping level slightly affects the detector parameters, while increasing its width, the photocurrent and the breakdown voltage also increase. The detector structure proposed in this work allows us to obtain a comparable gain and lower dark currents to the APD detectors made of InGaAsSb previously presented in the literature. The performed simulations confirmed the possibility of obtaining APDs with high performance at room temperatures made of InGaAsSb for the SWIR range.
- Open Access
Theoretical Study of Quaternary nBp InGaAsSb SWIR Detectors for Room Temperature Condition
This paper presents a theoretical analysis of an nBp infrared barrier detector’s performance intended to operate at a room temperature (300 K) based on AIIIBV materials—In1-xGaxAsySb1−y quaternary compound—lattice-matched to the GaSb substrate with a p-n heterojunction ternary Al1−xGaxSb barrier. Numerical simulations were performed using a commercial Crosslight Software—package APSYS. The band structure of the nBp detector and the electric field distribution for the p-n heterojunction with and without a potential barrier were determined. The influence of the barrier-doping level on the detector parameters was analyzed. It was shown that Shockley-Read-Hall (SRH) recombination plays a decisive role in carrier transport for lifetimes shorter than 100 ns. The influence of the absorber/barrier thickness on the detector’s dark current density and photocurrent was investigated. It was shown that valence band offset does not influence the device’s performance. The quantum efficiency reaches its maximum value for an absorber’s thickness of ~3 μm. The performed simulations confirmed the possibility of the detector’s fabrication exhibiting high performance at room temperature based on quaternary compounds of AIIIBV materials for the short wavelength infrared range.
Open AccessTheoretical Study of Quaternary nBp InGaAsSb SWIR Detectors for Room Temperature Condition
This paper presents a theoretical analysis of an nBp infrared barrier detector’s performance intended to operate at a room temperature (300 K) based on AIIIBV materials—In1-xGaxAsySb1−y quaternary compound—lattice-matched to the GaSb substrate with a p-n heterojunction ternary Al1−xGaxSb barrier. Numerical simulations were performed using a commercial Crosslight Software—package APSYS. The band structure of the nBp detector and the electric field distribution for the p-n heterojunction with and without a potential barrier were determined. The influence of the barrier-doping level on the detector parameters was analyzed. It was shown that Shockley-Read-Hall (SRH) recombination plays a decisive role in carrier transport for lifetimes shorter than 100 ns. The influence of the absorber/barrier thickness on the detector’s dark current density and photocurrent was investigated. It was shown that valence band offset does not influence the device’s performance. The quantum efficiency reaches its maximum value for an absorber’s thickness of ~3 μm. The performed simulations confirmed the possibility of the detector’s fabrication exhibiting high performance at room temperature based on quaternary compounds of AIIIBV materials for the short wavelength infrared range.
- Open Access
- 26 August 2024
- Published by MDPI AG in Nanomaterials
- Vol. 14 (17) , 1393
Optical Characterization of the Interband Cascade LWIR Detectors with Type-II InAs/InAsSb Superlattice Absorber
The long-wave infrared (LWIR) interband cascade detector with type-II superlattices (T2SLs) and a gallium-free (“Ga-free”) InAs/InAsSb (x = 0.39) absorber was characterized by photoluminescence (PL) and spectral response (SR) methods. Heterostructures were grown by molecular beam epitaxy (MBE) on a GaAs substrate (001) orientation. The crystallographic quality was confirmed by high-resolution X-Ray diffraction (HRXRD). Two independent methods, combined with theoretical calculations, were able to determine the transitions between the superlattice minibands. Moreover, transitions from the trap states were determined. Studies of the PL intensity as a function of the excitation laser power allowed the identification of optical transitions. The determined effective energy gap (Eg) of the tested absorber layer was 116 meV at 300 K. The transition from the first light hole miniband to the first electron miniband was red-shifted by 76 meV. The detected defects’ energy states were constant versus temperature. Their values were 85 meV and 112 meV, respectively. Moreover, two additional transitions from acceptor levels in cryogenic temperature were determined by being shifted from blue to Eg by 6 meV and 16 meV, respectively.
- 26 August 2024
- Published by MDPI AG in Nanomaterials
- Vol. 14 (17) , 1393
Open AccessOptical Characterization of the Interband Cascade LWIR Detectors with Type-II InAs/InAsSb Superlattice Absorber
The long-wave infrared (LWIR) interband cascade detector with type-II superlattices (T2SLs) and a gallium-free (“Ga-free”) InAs/InAsSb (x = 0.39) absorber was characterized by photoluminescence (PL) and spectral response (SR) methods. Heterostructures were grown by molecular beam epitaxy (MBE) on a GaAs substrate (001) orientation. The crystallographic quality was confirmed by high-resolution X-Ray diffraction (HRXRD). Two independent methods, combined with theoretical calculations, were able to determine the transitions between the superlattice minibands. Moreover, transitions from the trap states were determined. Studies of the PL intensity as a function of the excitation laser power allowed the identification of optical transitions. The determined effective energy gap (Eg) of the tested absorber layer was 116 meV at 300 K. The transition from the first light hole miniband to the first electron miniband was red-shifted by 76 meV. The detected defects’ energy states were constant versus temperature. Their values were 85 meV and 112 meV, respectively. Moreover, two additional transitions from acceptor levels in cryogenic temperature were determined by being shifted from blue to Eg by 6 meV and 16 meV, respectively.
- Open Access
Non-Equilibrium Long-Wave Infrared HgCdTe Photodiodes: How the Exclusion and Extraction Junctions Work Separately
The cooling requirement for long-wave infrared detectors still creates significant limitations to their functionality. The phenomenon of minority-carrier exclusion and extraction in narrow-gap semiconductors has been intensively studied for over three decades and used to increase the operating temperatures of devices. Decreasing free carrier concentrations below equilibrium values by a stationary non-equilibrium depletion of the device absorber leads to a suppression of Auger generation. In this paper, we focus on analyzing exclusion and extraction effects separately, based on experimental and theoretical results for a HgCdTe photodiode. To carry out an experiment, the n+-P+-π-N+ heterostructure was grown by metal organic chemical vapor deposition on CdTe-buffered GaAs substrate. In order to separate the extraction and exclusive junctions, three different devices were evaluated: (1) a detector etched through the entire n+-P+-π-N+ heterostructure, (2) a detector made of the P+-π photoconductive junction and (3) a detector made of the π-N+ photodiode junction. For each device, the dark current density–voltage characteristics were measured at a high-temperature range, from 195 K to 300 K. Next, the carrier concentration distribution across the entire heterostructure and individual junctions was calculated using the APSYS simulation program. It was shown that when the n+-P+-π-N+ photodiode is reverse biased, the electron concentration in the π absorber drops below its thermal equilibrium value, due to the exclusion effect at the P+-π junction and the extraction effect at the π-N+ junction. To maintain the charge neutrality, the hole concentration is also reduced below the equilibrium value and reaches the absorber doping level (NA), leading to the Auger generation rate’s reduction by a factor of 2ni/NA, where ni is the intrinsic carrier concentration. Our experiment conducted for three separate detectors showed that the exclusion P+-π photoconductive junction has the most significant effect on the Auger suppression—the majority of the hole concentration drops to the doping level not only at the P+-π interface but also deep inside the π absorber.
Open AccessNon-Equilibrium Long-Wave Infrared HgCdTe Photodiodes: How the Exclusion and Extraction Junctions Work Separately
The cooling requirement for long-wave infrared detectors still creates significant limitations to their functionality. The phenomenon of minority-carrier exclusion and extraction in narrow-gap semiconductors has been intensively studied for over three decades and used to increase the operating temperatures of devices. Decreasing free carrier concentrations below equilibrium values by a stationary non-equilibrium depletion of the device absorber leads to a suppression of Auger generation. In this paper, we focus on analyzing exclusion and extraction effects separately, based on experimental and theoretical results for a HgCdTe photodiode. To carry out an experiment, the n+-P+-π-N+ heterostructure was grown by metal organic chemical vapor deposition on CdTe-buffered GaAs substrate. In order to separate the extraction and exclusive junctions, three different devices were evaluated: (1) a detector etched through the entire n+-P+-π-N+ heterostructure, (2) a detector made of the P+-π photoconductive junction and (3) a detector made of the π-N+ photodiode junction. For each device, the dark current density–voltage characteristics were measured at a high-temperature range, from 195 K to 300 K. Next, the carrier concentration distribution across the entire heterostructure and individual junctions was calculated using the APSYS simulation program. It was shown that when the n+-P+-π-N+ photodiode is reverse biased, the electron concentration in the π absorber drops below its thermal equilibrium value, due to the exclusion effect at the P+-π junction and the extraction effect at the π-N+ junction. To maintain the charge neutrality, the hole concentration is also reduced below the equilibrium value and reaches the absorber doping level (NA), leading to the Auger generation rate’s reduction by a factor of 2ni/NA, where ni is the intrinsic carrier concentration. Our experiment conducted for three separate detectors showed that the exclusion P+-π photoconductive junction has the most significant effect on the Auger suppression—the majority of the hole concentration drops to the doping level not only at the P+-π interface but also deep inside the π absorber.
- Open Access
- 6 February 2024
- Published by Polish Academy of Sciences Chancellery in Bulletin Of The Polish Academy Of Sciences-Technical Sciences
- Vol. 72 (3) , 149173
Investigation of HgCdTe avalanche photodiodes for HOT condition
- 6 February 2024
- Published by Polish Academy of Sciences Chancellery in Bulletin Of The Polish Academy Of Sciences-Technical Sciences
- Vol. 72 (3) , 149173
Open AccessInvestigation of HgCdTe avalanche photodiodes for HOT condition
- Open Access
- 5 May 2023
- Published by Polish Academy of Sciences Chancellery in Opto-Electronics Review
- Vol. 31 (2) , 145093
Theoretical study of back-to-back avalanche photodiodes for dual-band infrared applications
The dual-band avalanche photodiode (APD) detector based on a HgCdTe material system was designed and analysed in detail numerically. A theoretical analysis of the two-colour APD intended for the mid wavelength infrared (MWIR) and long wavelength infrared (LWIR) ranges was conducted. The main purpose of the work was to indicate an approach to select APD structure parameters to achieve the best performance at high operating temperatures (HOT). The numerical simulations were performed by Crosslight numerical APSYS platform which is designed to simulate semiconductor optoelectronic devices. The current-voltage characteristics, current gain, and excess noise analysis at temperature T = 230 K vs. applied voltage for MWIR (U = 15 V) and LWIR (U = –6 V) ranges were performed. The influence of low and high doping in both active layers and barrier on the current gain and excess noise is shown. It was presented that an increase of the APD active layer doping leads to an increase in the photocurrent gain in the LWIR detector and a decrease in the MWIR device. The dark current and photocurrent gains were compared. Photocurrent gain is higher in both spectral ranges.
- 5 May 2023
- Published by Polish Academy of Sciences Chancellery in Opto-Electronics Review
- Vol. 31 (2) , 145093
Open AccessTheoretical study of back-to-back avalanche photodiodes for dual-band infrared applications
The dual-band avalanche photodiode (APD) detector based on a HgCdTe material system was designed and analysed in detail numerically. A theoretical analysis of the two-colour APD intended for the mid wavelength infrared (MWIR) and long wavelength infrared (LWIR) ranges was conducted. The main purpose of the work was to indicate an approach to select APD structure parameters to achieve the best performance at high operating temperatures (HOT). The numerical simulations were performed by Crosslight numerical APSYS platform which is designed to simulate semiconductor optoelectronic devices. The current-voltage characteristics, current gain, and excess noise analysis at temperature T = 230 K vs. applied voltage for MWIR (U = 15 V) and LWIR (U = –6 V) ranges were performed. The influence of low and high doping in both active layers and barrier on the current gain and excess noise is shown. It was presented that an increase of the APD active layer doping leads to an increase in the photocurrent gain in the LWIR detector and a decrease in the MWIR device. The dark current and photocurrent gains were compared. Photocurrent gain is higher in both spectral ranges.
- Open Access
Research on Electro-Optical Characteristics of Infrared Detectors with HgCdTe Operating at Room Temperature
This paper presents a thorough analysis of the current–voltage characteristics of uncooled HgCdTe detectors optimized for different spectral ranges. HgCdTe heterostructures were grown by means of metal–organic chemical vapor deposition (MOCVD) on GaAs substrates. The obtained detector structures were measured using a Keysight B1500A semiconductor device analyser controlled via LabVIEW for automation. The experimental characteristics were compared with numerical calculations performed using the commercial platform SimuAPSYS (Crosslight). SimuAPSYS supports detector design and allows one to understand different mechanisms occurring in the analysed structures. The dark current density experimental data were compared with theoretical results at a temperature of 300 K for short, medium, and long wavelength infrared ranges. The dark current density of detectors optimized for different wavelengths was determined using various generation–recombination mechanisms. Proper matching between experimental and theoretical data was obtained by shifting the Shockley–Read–Hall carrier lifetime and the Auger–1 and Auger–7 recombination rates. Exemplary spectral responses were also discussed, giving a better insight into detector performance. The matching level was proven with a theoretical evaluation of the zero-bias dynamic resistance–area product (R0A) and the current responsivity of the designed detectors.
Open AccessResearch on Electro-Optical Characteristics of Infrared Detectors with HgCdTe Operating at Room Temperature
This paper presents a thorough analysis of the current–voltage characteristics of uncooled HgCdTe detectors optimized for different spectral ranges. HgCdTe heterostructures were grown by means of metal–organic chemical vapor deposition (MOCVD) on GaAs substrates. The obtained detector structures were measured using a Keysight B1500A semiconductor device analyser controlled via LabVIEW for automation. The experimental characteristics were compared with numerical calculations performed using the commercial platform SimuAPSYS (Crosslight). SimuAPSYS supports detector design and allows one to understand different mechanisms occurring in the analysed structures. The dark current density experimental data were compared with theoretical results at a temperature of 300 K for short, medium, and long wavelength infrared ranges. The dark current density of detectors optimized for different wavelengths was determined using various generation–recombination mechanisms. Proper matching between experimental and theoretical data was obtained by shifting the Shockley–Read–Hall carrier lifetime and the Auger–1 and Auger–7 recombination rates. Exemplary spectral responses were also discussed, giving a better insight into detector performance. The matching level was proven with a theoretical evaluation of the zero-bias dynamic resistance–area product (R0A) and the current responsivity of the designed detectors.