Xuewu Hong
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Xuewu Hong has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Jian Zhao
School of Control and Mechanical Engineering, Tianjin Chengjian University, Tianjin, China
2 shared publications - Chang Liu
School of Mechanical Engineering Tiangong University Tianjin China
1 shared publication - Guangming Sun
School of Control and Mechanical Engineering, Tianjin Chengjian University, Tianjin, China
1 shared publication - Jingjing Yang
School of Control and Mechanical Engineering, Tianjin Chengjian University, Tianjin, China
1 shared publication - Sinan Liu
School of Control and Mechanical Engineering, Tianjin Chengjian University, Tianjin, China
1 shared publication Siqi Chen
School of Control and Mechanical Engineering, Tianjin Chengjian University, Tianjin, China
1 shared publication
Latest Publications
- 4 March 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
Prediction model in drilling of unidirectional thermoplastic CF/PEEK composite laminates considering the chisel edge
Carbon fiber reinforced thermoplastic composites (CFRTP) are increasingly becoming critical lightweight and high-efficiency materials in manufacturing fields such as aerospace and defense technology, owing to their high strength, high modulus, and environmentally friendly recyclability. As a high-performance CFRTP, carbon fiber reinforced polyetheretherketone (CF/PEEK) composites are typically joined with other materials through drilling, where the thrust force is a key parameter affecting hole quality. A novel predictive model for the thrust force in unidirectional CF/PEEK (UD-CF/PEEK) composites was established based on the two-parameter elastic foundation theory and Hertz contact, taking into account tool structure and material characteristics. Experimental validation results showed that the prediction errors for the thrust forces of the chisel edge and the main cutting edge were 1.46% and 8.89%, respectively, and the prediction error for the total thrust force was 6.27%. Furthermore, by investigating the influence of different drilling parameters on the thrust force of UD-CF/PEEK, it was found that at a constant spindle speed, an increase in the feed rate leads to a rising trend in the thrust forces of both the chisel edge and the main cutting edge. This finding provides theoretical guidance for low-damage hole-making in thermoplastic CF/PEEK composites.
- 4 March 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
Prediction model in drilling of unidirectional thermoplastic CF/PEEK composite laminates considering the chisel edge
Carbon fiber reinforced thermoplastic composites (CFRTP) are increasingly becoming critical lightweight and high-efficiency materials in manufacturing fields such as aerospace and defense technology, owing to their high strength, high modulus, and environmentally friendly recyclability. As a high-performance CFRTP, carbon fiber reinforced polyetheretherketone (CF/PEEK) composites are typically joined with other materials through drilling, where the thrust force is a key parameter affecting hole quality. A novel predictive model for the thrust force in unidirectional CF/PEEK (UD-CF/PEEK) composites was established based on the two-parameter elastic foundation theory and Hertz contact, taking into account tool structure and material characteristics. Experimental validation results showed that the prediction errors for the thrust forces of the chisel edge and the main cutting edge were 1.46% and 8.89%, respectively, and the prediction error for the total thrust force was 6.27%. Furthermore, by investigating the influence of different drilling parameters on the thrust force of UD-CF/PEEK, it was found that at a constant spindle speed, an increase in the feed rate leads to a rising trend in the thrust forces of both the chisel edge and the main cutting edge. This finding provides theoretical guidance for low-damage hole-making in thermoplastic CF/PEEK composites.
- Open Access
- 18 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 89965-89973
Modeling Method for Pose Error of Machine Tool Linear Feed System Based on the Principle of Minimum Potential Energy
In the present research, a method to model the pose error of the machine tool feed system is proposed based on the principle of minimum potential energy. Firstly, the force-moment equilibrium equation of the feed system is established by mechanical analysis. Secondly, the force of the single slider is analyzed based on Hertzian contact theory, and the force state of the slider under the action of the guideway error is obtained. The elastic displacements of the single slider in the horizontal and vertical directions are solved based on the principle of the minimal potential energy. Subsequently, the pose error of the feeding system is obtained by using the plane fitting principle. Finally, the correctness of the proposed method is verified through experiments, and the experimental results are in good agreement with the theoretical results.
- 18 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 89965-89973
Open AccessModeling Method for Pose Error of Machine Tool Linear Feed System Based on the Principle of Minimum Potential Energy
In the present research, a method to model the pose error of the machine tool feed system is proposed based on the principle of minimum potential energy. Firstly, the force-moment equilibrium equation of the feed system is established by mechanical analysis. Secondly, the force of the single slider is analyzed based on Hertzian contact theory, and the force state of the slider under the action of the guideway error is obtained. The elastic displacements of the single slider in the horizontal and vertical directions are solved based on the principle of the minimal potential energy. Subsequently, the pose error of the feeding system is obtained by using the plane fitting principle. Finally, the correctness of the proposed method is verified through experiments, and the experimental results are in good agreement with the theoretical results.