Chunqiang Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Chunqiang Wang has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Jingbo Wei
School of Aeronautics and Astronautics, Sun Yat-sen University, Shenzhen 518107, China
2 shared publications - Kun Liu
School of Aeronautics and Astronautics, Sun Yat-sen University, Shenzhen 518107, China
2 shared publications - Zijie Qin
The School of Aeronautics and Astronautics, Sun Yat-sen University, Shenzhen, China
2 shared publications - Mingzhi Cao
School of Aeronautics and Astronautics, Sun Yat-sen University, Shenzhen 518107, China
1 shared publication - Xiaobin Yu
School of Aeronautics and Astronautics, Sun Yat-sen University, Shenzhen 518107, China
1 shared publication - Xinliang Li
School of Aeronautics and Astronautics, Sun Yat-sen University, Shenzhen, China
1 shared publication
Latest Publications
- 15 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 9 (12) , 11010-11017
Improving the Controller Performance of a Tilt-Rotor Octocopter by Compensating for the Tilt Angle's Dynamics
This paper presents a novel control allocation compensator for a tilt-rotor octocopter using passive hinges, aimed at enhancing attitude control performance by accounting for the dynamic characteristics of the actuators. The introduction of a passive hinging mechanism results in a slower tilt angle response compared to servo-actuated systems, which, if overlooked, can significantly degrade controller performance. In this regard, the paper first models the arm's tilting dynamics and discusses its impact on control allocation errors. A two-part compensator is then introduced to address these dynamics: the first part adds a simple control loop to the control allocation module to quicken the tilt response; the second part re-allocates the thrust based on estimated tilt angles, leveraging the motor's rapid response to offset the slow response of the tilt angle. By simultaneously accelerating the tilt response and reallocating thrusts, the compensator minimizes control allocation error, thereby enhancing the accuracy of position and attitude control. The effectiveness of the proposed method is validated through both simulations and real flight experiments.
- 15 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 9 (12) , 11010-11017
Improving the Controller Performance of a Tilt-Rotor Octocopter by Compensating for the Tilt Angle's Dynamics
This paper presents a novel control allocation compensator for a tilt-rotor octocopter using passive hinges, aimed at enhancing attitude control performance by accounting for the dynamic characteristics of the actuators. The introduction of a passive hinging mechanism results in a slower tilt angle response compared to servo-actuated systems, which, if overlooked, can significantly degrade controller performance. In this regard, the paper first models the arm's tilting dynamics and discusses its impact on control allocation errors. A two-part compensator is then introduced to address these dynamics: the first part adds a simple control loop to the control allocation module to quicken the tilt response; the second part re-allocates the thrust based on estimated tilt angles, leveraging the motor's rapid response to offset the slow response of the tilt angle. By simultaneously accelerating the tilt response and reallocating thrusts, the compensator minimizes control allocation error, thereby enhancing the accuracy of position and attitude control. The effectiveness of the proposed method is validated through both simulations and real flight experiments.
- Open Access
Research on the Distributed Propeller Slipstream Effect of UAV Wing Based on the Actuator Disk Method
Distributed electric propulsion technology has great potential and advantages in the development of drones. In this paper, to study the slipstream effect of distributed propellers, the actuator disk method was used to verify a single propeller, and the calculated thrust was in good agreement with the test results. Then, based on the actuator disk method, the influence of different installation positions on the slipstream effect was studied, and the distributed propeller layout was optimized by a genetic algorithm to improve the low-speed performance of the unmanned aerial vehicle (UAV) during the take-off phase and increase the cruise duration. The analysis results showed that the lift of the wing will be larger when the propellers are higher than the wing. The wing lift and drag of the counter-rotating are less than those of the co-rotating. Compared with the original layout, the lift coefficient of the optimized distributed propeller layout is significantly increased by 30.97%, while the lift/drag ratio is increased by 7.34%. Finally, we designed the test platform and qualitatively verified the calculated results without quantitative verification.
Open AccessResearch on the Distributed Propeller Slipstream Effect of UAV Wing Based on the Actuator Disk Method
Distributed electric propulsion technology has great potential and advantages in the development of drones. In this paper, to study the slipstream effect of distributed propellers, the actuator disk method was used to verify a single propeller, and the calculated thrust was in good agreement with the test results. Then, based on the actuator disk method, the influence of different installation positions on the slipstream effect was studied, and the distributed propeller layout was optimized by a genetic algorithm to improve the low-speed performance of the unmanned aerial vehicle (UAV) during the take-off phase and increase the cruise duration. The analysis results showed that the lift of the wing will be larger when the propellers are higher than the wing. The wing lift and drag of the counter-rotating are less than those of the co-rotating. Compared with the original layout, the lift coefficient of the optimized distributed propeller layout is significantly increased by 30.97%, while the lift/drag ratio is increased by 7.34%. Finally, we designed the test platform and qualitatively verified the calculated results without quantitative verification.