Nikolaos Koutroumanis
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Nikolaos Koutroumanis has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Costas Galiotis
University of Patras
4 shared publications - Maria Giovanna Pastore Carbone
Department of Mechanical Engineering University of the Peloponnese Patras Greece
3 shared publications - George Paterakis
Institute of Chemical Engineering Sciences, Foundation of Research and Technology-Hellas (FORTH/ICE-HT), Stadiou Street, Platani, 26504 Patras, Greece
2 shared publications - Julio Gómez
Avanzare Innovación Tecnológica S.L. Navarrete Spain
2 shared publications - Anastasios C. Manikas
Department of Chemical Engineering, University of Patras, Patras, Greece
1 shared publication - Antonios Akouros
Institute of Chemical Engineering Sciences, platani, Patras, Western Greece, 26504, GREECE
1 shared publication
Latest Publications
- Open Access
- 17 July 2026
- Published by Wiley in Polymers for Advanced Technologies
- Vol. 37 (7) , e70676
Effect of Processing Routes on the Performance of Reduced Graphene Oxide‐Enhanced Polyamide 6
Reduced graphene oxide (rGO)‐reinforced polyamide 6 (PA6) nanocomposites were developed using industrially scalable masterbatch dilution strategies to establish a practical route for producing multifunctional materials at very low filler loadings. A concentrated PA6 masterbatch containing 2.0% w/w rGO was diluted to obtain nanocomposites with 0.05% and 0.10% w/w rGO through two processing routes: (i) a conventional two‐step process involving twin‐screw compounding followed by injection molding and (ii) direct dilution during injection molding using different screw configurations. The influence of processing on structure–property relationships was investigated by differential scanning calorimetry, thermogravimetric analysis, X‐ray diffraction, tensile testing, contact‐angle measurements with AdBlue, long‐term ethanol absorption experiments, and accelerated UV‐aging tests. Both the conventional route and the single‐step injection‐molding route employing a long screw achieved homogeneous rGO distribution, whereas the short‐screw configuration resulted in insufficient mixing and inferior mechanical properties. The incorporation of rGO using the two‐step process preserved the thermal transitions and crystalline structure of PA6 while moderately increasing stiffness and influencing crystallinity at higher filler loading. In addition, the nanocomposites exhibited reduced ethanol uptake, increased hydrophobicity toward AdBlue, and improved resistance to UV‐induced yellowing and surface degradation compared with neat PA6. These improvements were achieved without compromising the processability or intrinsic characteristics of the polymer matrix. The results demonstrate that direct masterbatch dilution during injection molding, when combined with an optimized screw configuration, can provide an efficient alternative to conventional multi‐step compounding. This approach offers a scalable and cost‐effective route for manufacturing graphene‐enhanced PA6 components with improved mechanical performance, chemical resistance, and environmental durability for automotive and industrial applications.
- 17 July 2026
- Published by Wiley in Polymers for Advanced Technologies
- Vol. 37 (7) , e70676
Open AccessEffect of Processing Routes on the Performance of Reduced Graphene Oxide‐Enhanced Polyamide 6
Reduced graphene oxide (rGO)‐reinforced polyamide 6 (PA6) nanocomposites were developed using industrially scalable masterbatch dilution strategies to establish a practical route for producing multifunctional materials at very low filler loadings. A concentrated PA6 masterbatch containing 2.0% w/w rGO was diluted to obtain nanocomposites with 0.05% and 0.10% w/w rGO through two processing routes: (i) a conventional two‐step process involving twin‐screw compounding followed by injection molding and (ii) direct dilution during injection molding using different screw configurations. The influence of processing on structure–property relationships was investigated by differential scanning calorimetry, thermogravimetric analysis, X‐ray diffraction, tensile testing, contact‐angle measurements with AdBlue, long‐term ethanol absorption experiments, and accelerated UV‐aging tests. Both the conventional route and the single‐step injection‐molding route employing a long screw achieved homogeneous rGO distribution, whereas the short‐screw configuration resulted in insufficient mixing and inferior mechanical properties. The incorporation of rGO using the two‐step process preserved the thermal transitions and crystalline structure of PA6 while moderately increasing stiffness and influencing crystallinity at higher filler loading. In addition, the nanocomposites exhibited reduced ethanol uptake, increased hydrophobicity toward AdBlue, and improved resistance to UV‐induced yellowing and surface degradation compared with neat PA6. These improvements were achieved without compromising the processability or intrinsic characteristics of the polymer matrix. The results demonstrate that direct masterbatch dilution during injection molding, when combined with an optimized screw configuration, can provide an efficient alternative to conventional multi‐step compounding. This approach offers a scalable and cost‐effective route for manufacturing graphene‐enhanced PA6 components with improved mechanical performance, chemical resistance, and environmental durability for automotive and industrial applications.
- Open Access
- 5 April 2026
- Published by Wiley in Polymer Composites
- Vol. 47 (13) , 12086-12096
Masterbatch‐Assisted Fabrication of Polylactic Acid/Reduced Graphene Oxide Nanocomposites Exhibiting Mechanical Enhancement and UV ‐C Aging Resistance
Polylactic acid (PLA) is a promising bio‐based polymer; nonetheless, its extensive application is still limited by poor fracture toughness, low thermal stability, and strong susceptibility to degradation induced by ultraviolet (UV) radiation. In this study, nanocomposites of PLA with reduced graphene oxide (rGO) were prepared through a masterbatch dilution approach. First, a PLA/2 wt% was produced by twin‐screw extrusion, a process compatible with current industrial practices. The masterbatch was subsequently diluted with neat PLA via melt compounding and processed into films by compression molding. The structural, thermal, mechanical, and aging behaviors of the PLA/rGO nanocomposites were systematically investigated, showing improvement compared to neat polymer. The presence of rGO was found to influence the mechanical and thermo‐mechanical response, with both Young's modulus and the storage modulus increasing with filler content, reaching values up to 20%–25% higher than those of neat PLA. Notably, the nanocomposites presented strong resistance to accelerated UV‐C aging; while neat PLA underwent severe cracking, showing a reduction of glass transition temperature of ca. 14°C, and complete mechanical failure, the composites retained their initial morphology and preserved their initial mechanical performance to a great extent, maintaining up to 73% of the original Young's modulus and up to 94% of initial tensile strength. These findings highlight the potential of the masterbatch route for producing durable PLA nanocomposites through industrially compatible processing routes, thus extending the applicability of this bio‐based polymer in several fields, such as automotive and consumer products.
- 5 April 2026
- Published by Wiley in Polymer Composites
- Vol. 47 (13) , 12086-12096
Open AccessMasterbatch‐Assisted Fabrication of Polylactic Acid/Reduced Graphene Oxide Nanocomposites Exhibiting Mechanical Enhancement and UV ‐C Aging Resistance
Polylactic acid (PLA) is a promising bio‐based polymer; nonetheless, its extensive application is still limited by poor fracture toughness, low thermal stability, and strong susceptibility to degradation induced by ultraviolet (UV) radiation. In this study, nanocomposites of PLA with reduced graphene oxide (rGO) were prepared through a masterbatch dilution approach. First, a PLA/2 wt% was produced by twin‐screw extrusion, a process compatible with current industrial practices. The masterbatch was subsequently diluted with neat PLA via melt compounding and processed into films by compression molding. The structural, thermal, mechanical, and aging behaviors of the PLA/rGO nanocomposites were systematically investigated, showing improvement compared to neat polymer. The presence of rGO was found to influence the mechanical and thermo‐mechanical response, with both Young's modulus and the storage modulus increasing with filler content, reaching values up to 20%–25% higher than those of neat PLA. Notably, the nanocomposites presented strong resistance to accelerated UV‐C aging; while neat PLA underwent severe cracking, showing a reduction of glass transition temperature of ca. 14°C, and complete mechanical failure, the composites retained their initial morphology and preserved their initial mechanical performance to a great extent, maintaining up to 73% of the original Young's modulus and up to 94% of initial tensile strength. These findings highlight the potential of the masterbatch route for producing durable PLA nanocomposites through industrially compatible processing routes, thus extending the applicability of this bio‐based polymer in several fields, such as automotive and consumer products.
- Open Access
- 2 May 2023
- Published by IOP Publishing in Nanotechnology
- Vol. 34 (29) , 295501
Highly stretchable strain sensors based on Marangoni self-assemblies of graphene and its hybrids with other 2D materials
Graphene and other two-dimensional materials (2DMs) have been shown to be promising candidates for the development of flexible and highly-sensitive strain sensors. However, the successful implementation of 2DMs in practical applications is slowed down by complex processing and still low sensitivity. Here, we report on a novel development of strain sensors based on Marangoni self-assemblies of graphene and of its hybrids with other 2DMs that can both withstand very large deformation and exhibit highly sensitive piezoresistive behaviour. By exploiting the Marangoni effect, reference films of self-assembled reduced graphene oxide (RGO) are first optimized, and the electromechanical behaviour has been assessed after deposition onto different elastomers demonstrating the potential of producing strain sensors suitable for different fields of application. Hybrid networks have been then prepared by adding hexagonal boron nitride (hBN) and fluorinated graphene (FGr) to the RGO dispersion. The hybrid integration of 2D materials is demonstrated to become a potential solution to increase substantially the sensitivity of the produced resistive strain sensors without compromising the mechanical integrity of the film. In fact, for large quasi-static deformations, a range of gauge factor values up to 2000 were demonstrated, while retaining a stable performance under cyclic deformations.
- 2 May 2023
- Published by IOP Publishing in Nanotechnology
- Vol. 34 (29) , 295501
Open AccessHighly stretchable strain sensors based on Marangoni self-assemblies of graphene and its hybrids with other 2D materials
Graphene and other two-dimensional materials (2DMs) have been shown to be promising candidates for the development of flexible and highly-sensitive strain sensors. However, the successful implementation of 2DMs in practical applications is slowed down by complex processing and still low sensitivity. Here, we report on a novel development of strain sensors based on Marangoni self-assemblies of graphene and of its hybrids with other 2DMs that can both withstand very large deformation and exhibit highly sensitive piezoresistive behaviour. By exploiting the Marangoni effect, reference films of self-assembled reduced graphene oxide (RGO) are first optimized, and the electromechanical behaviour has been assessed after deposition onto different elastomers demonstrating the potential of producing strain sensors suitable for different fields of application. Hybrid networks have been then prepared by adding hexagonal boron nitride (hBN) and fluorinated graphene (FGr) to the RGO dispersion. The hybrid integration of 2D materials is demonstrated to become a potential solution to increase substantially the sensitivity of the produced resistive strain sensors without compromising the mechanical integrity of the film. In fact, for large quasi-static deformations, a range of gauge factor values up to 2000 were demonstrated, while retaining a stable performance under cyclic deformations.