Bartlomiej Chojnacki
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Bartlomiej Chojnacki has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
Aleksandra Chojak
AGH University of Krakow, Cracow, Poland
2 shared publications- Anna Zofia Lesniewska
Institute of Psychology, Jagiellonian University, Ingardena 6, Krakow 30-060, Poland; Faculty of Psychological and Educational Sciences, Université Libre de Bruxelles, F.D. Roosevelt 50, Brussels B-1050, Belgium
2 shared publications Jan Pawlik
AGH University of Krakow, Cracow, Poland
2 shared publicationsJulia Idczak
AGH University of Krakow, Cracow, Poland
2 shared publications- Kamil Schynol
Form At Wood sp. z o.o., Technologiczna 2, 45-839 Opole, Poland
2 shared publications - Marek Binder
Institute of Psychology, Jagiellonian University, Ingardena 6, Krakow 30-060, Poland
2 shared publications
Latest Publications
- Open Access
Effect of Absorber Placement and Sound Source Type on Room-Acoustic Parameters in a Small Listening Room
The acoustic effect produced by a sound-absorbing material in a small room is not determined by laboratory material characterization and installed area alone; it also depends on spatial deployment and on how the room is excited. This study investigates the combined effects of absorbing-material placement and excitation-source characteristics in a full-scale small listening room. Twelve fixed-amount treatment configurations, each using 12 identical polyurethane-foam absorbers with a total nominal area of , were compared with an untreated reference. Measurements were performed using a quasi-omnidirectional Brüel & Kjær OmniPower 4292-L source and two directional loudspeakers, Genelec 8020D and AudioSolutions O302B Overture, in a fixed stereo-like source–listener geometry. Room impulse responses were evaluated in one-third-octave bands from 63 to 5000 Hz using and . The frequency-resolved results show substantial placement-dependent changes, with the strongest differences occurring mainly in the low and low-mid frequency ranges. As secondary descriptive summaries, the full-band mean reduction reached approximately 0.33 s and the mean increase approximately 5.9 dB, depending on source and configuration. The relative ordering of treatment configurations was itself source dependent. A representative time-domain comparison further showed source-dependent modification of early reflected energy, whereas later energy was reduced more consistently. The results demonstrate that laboratory material characterization, spatial deployment, source–listener geometry, and excitation conditions should be considered jointly when evaluating acoustic treatment in small listening rooms.Open AccessEffect of Absorber Placement and Sound Source Type on Room-Acoustic Parameters in a Small Listening Room
The acoustic effect produced by a sound-absorbing material in a small room is not determined by laboratory material characterization and installed area alone; it also depends on spatial deployment and on how the room is excited. This study investigates the combined effects of absorbing-material placement and excitation-source characteristics in a full-scale small listening room. Twelve fixed-amount treatment configurations, each using 12 identical polyurethane-foam absorbers with a total nominal area of , were compared with an untreated reference. Measurements were performed using a quasi-omnidirectional Brüel & Kjær OmniPower 4292-L source and two directional loudspeakers, Genelec 8020D and AudioSolutions O302B Overture, in a fixed stereo-like source–listener geometry. Room impulse responses were evaluated in one-third-octave bands from 63 to 5000 Hz using and . The frequency-resolved results show substantial placement-dependent changes, with the strongest differences occurring mainly in the low and low-mid frequency ranges. As secondary descriptive summaries, the full-band mean reduction reached approximately 0.33 s and the mean increase approximately 5.9 dB, depending on source and configuration. The relative ordering of treatment configurations was itself source dependent. A representative time-domain comparison further showed source-dependent modification of early reflected energy, whereas later energy was reduced more consistently. The results demonstrate that laboratory material characterization, spatial deployment, source–listener geometry, and excitation conditions should be considered jointly when evaluating acoustic treatment in small listening rooms. - Open Access
- 24 August 2026
- Published by Elsevier in Applied Acoustics
- Vol. 255
Assessment of a 1:8 physical scale model for comparative analysis of modal behaviour and early reflections in small rooms
- 24 August 2026
- Published by Elsevier in Applied Acoustics
- Vol. 255
Open AccessAssessment of a 1:8 physical scale model for comparative analysis of modal behaviour and early reflections in small rooms
- 21 March 2026
- Published by Elsevier in Biological Psychology
- Vol. 206, 109243
Sleep stages affect low-gamma range effective cortical connectivity for 40-Hz auditory steady-state responses
- 21 March 2026
- Published by Elsevier in Biological Psychology
- Vol. 206, 109243
Sleep stages affect low-gamma range effective cortical connectivity for 40-Hz auditory steady-state responses
- Open Access
Sleep affects low-gamma range effective cortical connectivity for 40-Hz auditory steady-state responses
The 40-Hz auditory steady-state response (40-Hz ASSR) is a sensitive marker of changes in arousal level, which has been reported to decrease during slow-wave sleep. However, sleep-related changes in directional connectivity during 40-Hz ASSR across cortical networks remain underexplored. In this study, we examined how wakefulness, NREM (N1, N2, N3) and REM sleep affect the direction and extent of neural signal propagation. EEG data during periodic 40-Hz auditory stimulation were collected during an overnight study from 29 normal-hearing human subjects (including 16 females). A source analysis was implemented to locate cortical activity, and effective connectivity was assessed with the Directed Transfer Function (DTF) in the low-gamma band (37-43 Hz). We focused on the connections between auditory cortical regions, prefrontal and temporo-parietal associative cortices. We hypothesized that: 1) feedback connections from associative to primary auditory areas will be the most affected by the arousal state changes; 2) associative reciprocal connectivity between prefrontal and temporo-parietal regions will display gradual connectivity reduction with increasing NREM sleep depth, with partial restoration during REM sleep. Our results showed that feedforward rather than feedback connectivity was most strongly disrupted during sleep, particularly in NREM N2 and N3 stages, contradicting our first hypothesis. The second hypothesis was supported: reciprocal connectivity between prefrontal and parietal associative cortices significantly decreased with sleep depth. Overall, our findings suggest that reduced cortical propagation of 40-Hz ASSR related neuronal signals during sleep primarily reflects a breakdown in bottom-up signal transmission, and a parallel weakening of reciprocal prefrontal-parietal coupling.
Open AccessSleep affects low-gamma range effective cortical connectivity for 40-Hz auditory steady-state responses
The 40-Hz auditory steady-state response (40-Hz ASSR) is a sensitive marker of changes in arousal level, which has been reported to decrease during slow-wave sleep. However, sleep-related changes in directional connectivity during 40-Hz ASSR across cortical networks remain underexplored. In this study, we examined how wakefulness, NREM (N1, N2, N3) and REM sleep affect the direction and extent of neural signal propagation. EEG data during periodic 40-Hz auditory stimulation were collected during an overnight study from 29 normal-hearing human subjects (including 16 females). A source analysis was implemented to locate cortical activity, and effective connectivity was assessed with the Directed Transfer Function (DTF) in the low-gamma band (37-43 Hz). We focused on the connections between auditory cortical regions, prefrontal and temporo-parietal associative cortices. We hypothesized that: 1) feedback connections from associative to primary auditory areas will be the most affected by the arousal state changes; 2) associative reciprocal connectivity between prefrontal and temporo-parietal regions will display gradual connectivity reduction with increasing NREM sleep depth, with partial restoration during REM sleep. Our results showed that feedforward rather than feedback connectivity was most strongly disrupted during sleep, particularly in NREM N2 and N3 stages, contradicting our first hypothesis. The second hypothesis was supported: reciprocal connectivity between prefrontal and parietal associative cortices significantly decreased with sleep depth. Overall, our findings suggest that reduced cortical propagation of 40-Hz ASSR related neuronal signals during sleep primarily reflects a breakdown in bottom-up signal transmission, and a parallel weakening of reciprocal prefrontal-parietal coupling.
- Open Access
Mitigation of Structural Vibrations in Sensitive Audio Devices: A Study on Isolation Materials for Lightweight Turntables
Effective vibration isolation is critical for minimizing the transmission of unwanted mechanical energy from a source to its surrounding environment, especially in precision systems, where even minor disturbances can degrade performance. This study addresses the challenge of low-frequency vibration transmission in lightweight, high-sensitivity audio devices such as turntables with masses below 10 kg. Traditional vibration mitigation strategies—primarily based on increasing system mass to raise the resonant frequency—are unsuitable for such systems due to weight constraints and potential impacts on operational dynamics. Previous studies have identified a critical resonance range of 5–15 Hz, corresponding to the tonearm and cartridge assembly, where transmitted vibrations can compromise signal fidelity and cause mechanical degradation. This research aims to develop an effective and universal vibration isolation solution tailored for lightweight turntables, focusing on external isolation from structural vibration sources such as furniture and flooring. To achieve this, a two-stage experimental methodology was employed. In the first stage, the excitation method with the use of a hammer tapping machine was evaluated for its ability to simulate real-world vibrational disturbances. The most representative excitation methods were then used in the second stage, where the isolation performance of various materials and systems was systematically assessed. Tested isolation strategies included steel springs, elastomeric dampers, and commercial linear vibration isolators. The effectiveness of each isolation material was quantified through spectral analysis and transfer function modeling of vibration acceleration data. The results provide comparative insights into material performance and offer design guidance for the development of compact, high-efficiency anti-vibration platforms for audio turntables and similar precision devices.
Open AccessMitigation of Structural Vibrations in Sensitive Audio Devices: A Study on Isolation Materials for Lightweight Turntables
Effective vibration isolation is critical for minimizing the transmission of unwanted mechanical energy from a source to its surrounding environment, especially in precision systems, where even minor disturbances can degrade performance. This study addresses the challenge of low-frequency vibration transmission in lightweight, high-sensitivity audio devices such as turntables with masses below 10 kg. Traditional vibration mitigation strategies—primarily based on increasing system mass to raise the resonant frequency—are unsuitable for such systems due to weight constraints and potential impacts on operational dynamics. Previous studies have identified a critical resonance range of 5–15 Hz, corresponding to the tonearm and cartridge assembly, where transmitted vibrations can compromise signal fidelity and cause mechanical degradation. This research aims to develop an effective and universal vibration isolation solution tailored for lightweight turntables, focusing on external isolation from structural vibration sources such as furniture and flooring. To achieve this, a two-stage experimental methodology was employed. In the first stage, the excitation method with the use of a hammer tapping machine was evaluated for its ability to simulate real-world vibrational disturbances. The most representative excitation methods were then used in the second stage, where the isolation performance of various materials and systems was systematically assessed. Tested isolation strategies included steel springs, elastomeric dampers, and commercial linear vibration isolators. The effectiveness of each isolation material was quantified through spectral analysis and transfer function modeling of vibration acceleration data. The results provide comparative insights into material performance and offer design guidance for the development of compact, high-efficiency anti-vibration platforms for audio turntables and similar precision devices.
- Open Access
- 17 April 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1) , 1-11
Accuracy of 3D printing of the samples in the prototyping of cavity-based metamaterials
Recent developments in designing cavity-based metamaterials require advanced methods for prototyping measurement samples, such as 3D printing techniques, which allow for the manufacture of complicated shapes unavailable for other technologies. However, the imperfections of the printouts, which vary for different printing technologies and printer settings, may cause differences between the designed and measured acoustic performance of the samples. This paper presents a complex study of the influence of printing details on the resulting sound absorption coefficient of a simple cavity-based metamaterial consisting of a coiled-up Helmholtz resonator. A general approach for manufacturing measurement samples is discussed. It is shown that the samples should be printed in one whenever possible, and joining the parts results in the formation of microslits and leads to mismatching of the sample impedance. Different printing technologies were also compared (SLS, DLP, FDM), and it was shown that for the studied geometry, the differences obtained for different printers are negligible from a practical point of view. The settings of the FDM printer were also studied for comparison with previous works by other authors. It was shown that the printer settings and the choice of filament are less important than random printing errors, which may occur regardless of the printer settings.
- 17 April 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1) , 1-11
Open AccessAccuracy of 3D printing of the samples in the prototyping of cavity-based metamaterials
Recent developments in designing cavity-based metamaterials require advanced methods for prototyping measurement samples, such as 3D printing techniques, which allow for the manufacture of complicated shapes unavailable for other technologies. However, the imperfections of the printouts, which vary for different printing technologies and printer settings, may cause differences between the designed and measured acoustic performance of the samples. This paper presents a complex study of the influence of printing details on the resulting sound absorption coefficient of a simple cavity-based metamaterial consisting of a coiled-up Helmholtz resonator. A general approach for manufacturing measurement samples is discussed. It is shown that the samples should be printed in one whenever possible, and joining the parts results in the formation of microslits and leads to mismatching of the sample impedance. Different printing technologies were also compared (SLS, DLP, FDM), and it was shown that for the studied geometry, the differences obtained for different printers are negligible from a practical point of view. The settings of the FDM printer were also studied for comparison with previous works by other authors. It was shown that the printer settings and the choice of filament are less important than random printing errors, which may occur regardless of the printer settings.
- Open Access
Application of Hybrid Absorptive–Diffusive Panels with Variable Acoustic Characteristics Based on Wooden Overlays Designed Using Third-Degree-of-Freedom Bezier Curves
This manuscript describes the application of novel hybrid acoustic panels with variable acoustic properties that could be used in the design process. Despite the significant growth in the modern acoustic absorbing and diffusing panel sector in recent years, there is still a need for sustainable and original designs that will fit standard interior design trends. The most significant requirement is satisfying the design needs of variable acoustic venues. The availability of acoustic panels with variable properties is minimal, as most designs are based on textiles in the form of rolling banners; therefore, there is no market diversity. The current paper presents an original solution for a novel perforated wooden panel based on third-degree-of-freedom curves. Due to the possibility of exchanging the front panel, the acoustic surface can be varied and adjusted to the room considering different requirements for the acoustic climate, for example, by modifying the attenuation range from low to mid–high frequencies. The novel panels have unique esthetic properties with functional acoustic features regarding sound diffusion and absorption. In this paper, sound absorption and diffusion measurements will be presented for the different variants of the panels, presenting the option to modify the parameters to adjust the panel’s features to the room’s needs. In situ acoustic measurements in a laboratory were conducted to test the variable acoustic panels’ influence on the room’s acoustic parameters, such as T30 and C80. In summary, the advantages of this kind of design will be discussed, alongside the possible impact on modern construction materials’ utilization in architecture.
Open AccessApplication of Hybrid Absorptive–Diffusive Panels with Variable Acoustic Characteristics Based on Wooden Overlays Designed Using Third-Degree-of-Freedom Bezier Curves
This manuscript describes the application of novel hybrid acoustic panels with variable acoustic properties that could be used in the design process. Despite the significant growth in the modern acoustic absorbing and diffusing panel sector in recent years, there is still a need for sustainable and original designs that will fit standard interior design trends. The most significant requirement is satisfying the design needs of variable acoustic venues. The availability of acoustic panels with variable properties is minimal, as most designs are based on textiles in the form of rolling banners; therefore, there is no market diversity. The current paper presents an original solution for a novel perforated wooden panel based on third-degree-of-freedom curves. Due to the possibility of exchanging the front panel, the acoustic surface can be varied and adjusted to the room considering different requirements for the acoustic climate, for example, by modifying the attenuation range from low to mid–high frequencies. The novel panels have unique esthetic properties with functional acoustic features regarding sound diffusion and absorption. In this paper, sound absorption and diffusion measurements will be presented for the different variants of the panels, presenting the option to modify the parameters to adjust the panel’s features to the room’s needs. In situ acoustic measurements in a laboratory were conducted to test the variable acoustic panels’ influence on the room’s acoustic parameters, such as T30 and C80. In summary, the advantages of this kind of design will be discussed, alongside the possible impact on modern construction materials’ utilization in architecture.
- Open Access
Dispersion Influence of Electroacoustic Transducer Parameters in the Design Process of Miniature Loudspeaker Arrays and Omnidirectional Sound Sources
Electroacoustic transducers represent one of the crucial materials used in the construction of loudspeaker arrays. The dispersion in their parameters may influence the performance of a speaker set. Parametric loudspeaker arrays and omnidirectional sound sources have been used for years. However, the possible influence of transducer manufacturing tolerances on the arrays’ performance has not been investigated. In previous research, the sources of possible dispersion in acoustic measurements carried out with omnidirectional sources were studied, pointing out that the problems with sound sources may be a significant reason behind the small measurement repeatability in standards. This paper investigated the measurement of several common types of miniature speakers, using 10 pieces of each type and investigating the influence of their parameter dispersion in electric and acoustic ways. Numerical simulations of omnidirectional sound sources were performed to investigate the drivers’ dispersion influence sensitivity. The results provided proof of the small-signal parameter dispersion reaching 20% of the variation. The acoustic measurements show that the loudspeakers may differ in sensitivity parameters by up to 4 dB in 10 transducer tests. The analysis of an example multitransducer array indicated that a dispersion of a sensitivity higher than 1 dB might lead to significant misperformance in constructed arrays and measurement deviations with this type of array.
Open AccessDispersion Influence of Electroacoustic Transducer Parameters in the Design Process of Miniature Loudspeaker Arrays and Omnidirectional Sound Sources
Electroacoustic transducers represent one of the crucial materials used in the construction of loudspeaker arrays. The dispersion in their parameters may influence the performance of a speaker set. Parametric loudspeaker arrays and omnidirectional sound sources have been used for years. However, the possible influence of transducer manufacturing tolerances on the arrays’ performance has not been investigated. In previous research, the sources of possible dispersion in acoustic measurements carried out with omnidirectional sources were studied, pointing out that the problems with sound sources may be a significant reason behind the small measurement repeatability in standards. This paper investigated the measurement of several common types of miniature speakers, using 10 pieces of each type and investigating the influence of their parameter dispersion in electric and acoustic ways. Numerical simulations of omnidirectional sound sources were performed to investigate the drivers’ dispersion influence sensitivity. The results provided proof of the small-signal parameter dispersion reaching 20% of the variation. The acoustic measurements show that the loudspeakers may differ in sensitivity parameters by up to 4 dB in 10 transducer tests. The analysis of an example multitransducer array indicated that a dispersion of a sensitivity higher than 1 dB might lead to significant misperformance in constructed arrays and measurement deviations with this type of array.
- Open Access
- 1 March 2024
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 155 (3_Suppleme) , A59
Acoustic metamaterial samples preparation for impedance tube measurements—The influence of different 3D printing techniques and mechanical post-processing on the simulation compliance
Prototyping of acoustic metamaterials frequently involves the use of additive manufacturing techniques. It offers the best price and the option for complex structure production, which is beneficial in the R&D process. Previously, some differences in acoustic metamaterial sound absorption measurement dispersions regarding using 3D printing techniques for sample preparation were noted. The sound absorption sensitivity on different printing settings or materials is usually omitted. The paper will present the research on the impedance tube measurements of absorbing metamaterial manufactured with different 3D printing methods and post-processed with mechanical and chemical treatment. Two approaches to metamaterial construction were analyzed in the current study—the single-solid metamaterial and the structure divided into parts, where the influence of assembly methods was investigated. To achieve the best compatibility with FEM or TMM modeling results, different post-processing techniques were involved, such as drilling, grinding, and sealant use. The presentation will describe the valuable paths used in sample preparation to achieve better compatibility between the measurements and simulations. The need for a comprehensive part preparation description in metamaterials research and papers will be discussed. [Work funded and supported by the Polish Government, National Centre of Research and Development, agreement no. LIDER/11/0065/L-12/20/NCBR/2021.]
- 1 March 2024
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 155 (3_Suppleme) , A59
Open AccessAcoustic metamaterial samples preparation for impedance tube measurements—The influence of different 3D printing techniques and mechanical post-processing on the simulation compliance
Prototyping of acoustic metamaterials frequently involves the use of additive manufacturing techniques. It offers the best price and the option for complex structure production, which is beneficial in the R&D process. Previously, some differences in acoustic metamaterial sound absorption measurement dispersions regarding using 3D printing techniques for sample preparation were noted. The sound absorption sensitivity on different printing settings or materials is usually omitted. The paper will present the research on the impedance tube measurements of absorbing metamaterial manufactured with different 3D printing methods and post-processed with mechanical and chemical treatment. Two approaches to metamaterial construction were analyzed in the current study—the single-solid metamaterial and the structure divided into parts, where the influence of assembly methods was investigated. To achieve the best compatibility with FEM or TMM modeling results, different post-processing techniques were involved, such as drilling, grinding, and sealant use. The presentation will describe the valuable paths used in sample preparation to achieve better compatibility between the measurements and simulations. The need for a comprehensive part preparation description in metamaterials research and papers will be discussed. [Work funded and supported by the Polish Government, National Centre of Research and Development, agreement no. LIDER/11/0065/L-12/20/NCBR/2021.]
- Open Access
- 7 December 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (24) , 13058
Comparison of Different Omnidirectional Sound Sources with the Validation of Coupled Speakers as a Measurement Source for Room Acoustics
Omnidirectional sources used in room acoustics usually take the form of multi-speaker sources. Few alternatives for the most commonly used dodecahedral sound source have been derived recently. The project aimed to measure room acoustic parameters using three different sound sources: a dodecahedron, a cube, and a new source of two coupled loudspeakers. The measurements were made by rotating the sources every 15 degrees. The differences in the EDT, T30, D50, and C80 parameters in the function of the rotation angle of the sources were analyzed. Statistical analysis was carried out to examine the sensitivity of the measured parameters’ JND (just a noticeable difference) on the source’s rotation angle. This presentation will show the results and analysis of measurements showing the influence of the used source on obtained parameters and the validation of coupled speakers’ use. A comprehensive discussion of the results obtained with different sources (coupled, dodecahedral, cubic) will be provided. The results confirmed using the coupled speakers as an alternative for omnidirectional sound source in the range of 250–2000 Hz.
- 7 December 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (24) , 13058
Open AccessComparison of Different Omnidirectional Sound Sources with the Validation of Coupled Speakers as a Measurement Source for Room Acoustics
Omnidirectional sources used in room acoustics usually take the form of multi-speaker sources. Few alternatives for the most commonly used dodecahedral sound source have been derived recently. The project aimed to measure room acoustic parameters using three different sound sources: a dodecahedron, a cube, and a new source of two coupled loudspeakers. The measurements were made by rotating the sources every 15 degrees. The differences in the EDT, T30, D50, and C80 parameters in the function of the rotation angle of the sources were analyzed. Statistical analysis was carried out to examine the sensitivity of the measured parameters’ JND (just a noticeable difference) on the source’s rotation angle. This presentation will show the results and analysis of measurements showing the influence of the used source on obtained parameters and the validation of coupled speakers’ use. A comprehensive discussion of the results obtained with different sources (coupled, dodecahedral, cubic) will be provided. The results confirmed using the coupled speakers as an alternative for omnidirectional sound source in the range of 250–2000 Hz.