XWXiancong Wang

Xiancong Wang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Xiancong Wang has a total of 7 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Mechanical Properties and Durability Performance of Low Liquid Limit Soil Stabilized by Industrial Solid Waste

    by Xiaoli Wang, Xiancong Wang, Pingfeng Fu, Jinjin Shi

    To improve the mechanical and durability properties of low liquid limit soil, an eco-friendly, all-solid, waste-based stabilizer (GSCFC) was proposed using five different industrial solid wastes: ground granulated blast-furnace slag (GGBS), steel slag (SS), coal fly ash (CFA), flue-gas desulfurization (FGD) gypsum, and carbide slag (CS). The mechanical and durability performance of GSCFC-stabilized soil were evaluated using unconfined compressive strength (UCS), California bearing ratio (CBR), and freeze–thaw and wet–dry cycles. The Rietveld method was employed to analyze the mineral phases in the GSCFC-stabilized soil. The optimal composition of the GSCFC stabilizer was determined as 15% SS, 12% GGBS, 16% FGD gypsum, 36% CS, and 12% CFA. The GSCFC-stabilized soil exhibited higher CBR values, with results of 31.38%, 77.13%, and 94.58% for 30, 50, and 98 blows, respectively, compared to 27.23%, 68.34%, and 85.03% for OPC. Additionally, GSCFC-stabilized soil demonstrated superior durability under dry–wet and freeze–thaw cycles, maintaining a 50% higher UCS (1.5 MPa) and a 58.6% lower expansion rate (3.16%) after 15 dry–wet cycles and achieving a BDR of 86.86% after 5 freeze–thaw cycles, compared to 65% for OPC. Rietveld analysis showed increased hydration products (ettringite by 2.63 times, C-S-H by 2.51 times), significantly enhancing soil strength. These findings highlight the potential of GSCFC-stabilized soil for durable road sub-base applications. This research provides theoretical and technical support for the development of sustainable, cost-effective, and eco-friendly soil stabilizers as alternatives to traditional cement-based stabilizers while also promoting the synergistic utilization of multiple solid wastes.


  • Open Access

    Performance Optimization of Alkaline Multi-Industrial Waste-Based Cementitious Materials for Soil Solidification

    by Xiaoli Wang, Xiancong Wang, Pingfeng Fu, Jinjin Shi, Miao Xu

    This study presents the development of eco-friendly cementitious materials for soil stabilization, based on alkaline multi-industrial waste (AMIW), using steel slag (SS), blast furnace slag (BFS), carbide slag (CS), fly ash (FA) and flue gas desulfurization gypsum (FGDG) as the raw materials. The optimal AMIW-based cementitious material composition determined through orthogonal experiments was SS:CS:FGDG:BFS:FA = 15:10:15:44:16. Central composite design (CCD) in response surface methodology (RSM) was employed to optimize the curing process parameters. The maximum 7-day unconfined compressive strength (7d UCS) was achieved under the optimal conditions of 18.51% moisture content, 11.46% curing agent content and 26.48 min of mix-grinding time. The 7d UCS of the AMIW-stabilized soil showed a 24% improvement over ordinary Portland cement (OPC)-stabilized soil. Rietveld refinement results demonstrated that the main hydration products of the stabilized soil were C-S-H and ettringite. After curing for 7 days to 28 days, the C-S-H content increased from 3.31% to 5.76%, while the ettringite content increased from 1.41% to 3.54%. Mercury intrusion porosimetry (MIP) and scanning electron microscopy (SEM) analysis revealed that with the extension of curing time, the pores of the stabilized soil become smaller and the structure becomes denser, resulting in an improvement in compressive strength.


  • Open Access

    Synergetic Mechanism of Multiple Industrial Solid Waste-Based Geopolymer Binder for Soil Stabilization: Optimization Using D-Optimal Mixture Design

    by Xiaoli Wang, Xiancong Wang, Pingfeng Fu, Bolan Lei, Jinjin Shi, Miao Xu

    In order to improve the comprehensive utilization rate of industrial solid waste and the road quality, a novel low-carbon and environmental friendly soil stabilizer is proposed. In this study, steel slag (SS), carbide slag (CS), blast furnace slag (BFS), fly ash (FA), and desulfurized gypsum (DG) were used as raw materials to develop a multiple industrial solid waste-based soil stabilizer (MSWSS). The optimal mix ratio of the raw materials determined by D-optimal design was as follows: 5% SS, 50% CS, 15% BFS, 15% DG, and 15% FA. The 7-day unconfined compressive strength (UCS) of MSWSS-stabilized soil was 1.7 MPa, which was 36% higher than stabilization with ordinary portland cement (OPC) and met the construction requirements of highways. After 7 days of curing, the UCS of MSWSS-stabilized soil was significantly higher than that in the OPC group. X-ray powder diffraction (XRD), thermogravimetric analysis (TGA), and scanning electron microscopy (SEM) analysis indicated that the prominent hydration products were ettringite (AFt) and C-S-H gel. The results showed that an amount of AFt and C-S-H were formed in the initial stage of curing, resulting in a rapid improvement in early UCS. As the curing proceeded, the content of AFt and C-S-H increased constantly and grew intertwined with each other, which lead to the denser microstructure of stabilized soil and better mechanical strength.


  • Open Access

    The Hydration Mechanisms of Co-Stabilization Saline Soils by Using Multiple Solid Wastes

    by Bolan Lei, Pingfeng Fu, Xiaoli Wang, Wen Ni, Siqi Zhang, Xiancong Wang, Jinjin Shi, Miao Xu

    In this paper, an approach was employed to fabricate a curing agent using multiple solid wastes. To determine the optimal mixing ratio, orthogonal and compaction tests were initially conducted, followed by a comparative analysis of the excitation effects elicited by sodium silicate and NaOH. Remarkably, sodium silicate demonstrated superior suitability as an activator. The final composition was established as follows: 4% sodium silicate, 26% carbide slag, 25% granulated blast furnace (GBF) slag, 35% coal fly ash, and 10% flue gas desulphurization (FGD) gypsum. Under controlled conditions of 20% of curing agent content, the unconfined compressive strength of the solidified soil at 7 d attained 1.54 MPa, thereby satisfying the rigorous construction requirements for highways across all levels. XRD and SEM-EDS analyses revealed that the principal hydration products in the system consisted of ettringite, Friedel’s salt, and C-S-H gel. These products enveloped the soil particles, with ettringite and Friedel’s salt intermingling and occupying the intricate framework formed by the gel. The synergistic interplay among the components ultimately fostered the development of a coherent soil structure and enhanced overall densification.