Osama Salem
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Osama Salem has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Dong Won Jung
Faculty of Applied Energy System, Major of Mechanical Engineering, Jeju National University, Jeju-Si, Republic of Korea
5 shared publications - Choon-Man Lee
Changwon National University
3 shared publications - Mahmoud Hewidy
Assistant Prof., Production Engineering & Machine Design Department, Faculty of Engineering and Technology, Menoufia University, Shebin El-Kom, Egypt
3 shared publications - Atif Niaz
Jeju National University
2 shared publications - Ho-In Jeong
Mechatronics Research Center, Changwon National University, Changwon 51140, Republic of Korea
2 shared publications - Ai Ting
Department of Mechanical Engineering, Jeju National University, Jeju 63243, Republic of Korea
1 shared publication
Latest Publications
- 30 April 2026
- Published by Springer Nature
- p. 51-62
Toward Intelligent Machining: A Comparative Study of ANN and Mathematical Models for Precision EDM of Nickel 200
- 30 April 2026
- Published by Springer Nature
- p. 51-62
Toward Intelligent Machining: A Comparative Study of ANN and Mathematical Models for Precision EDM of Nickel 200
- Open Access
Thermo-Structural and Dynamic Performance Analysis of a 42CrMo4 Steel Ball Screw Assembly
This study presents a comprehensive thermo-structural and modal analysis of a ball screw assembly. Thermal analysis revealed a maximum temperature of 29.1 °C at the ball nut, corresponding to a total rise of 7.1 °C above ambient. The resulting thermal deformation reached 77.81 μm, while the von Mises stress peaked at 53.9 MPa, both within acceptable limits. Modal simulation of 360 modes showed a sharp increase in frequency with mode number and larger deformation patterns at the higher modes. The first two modes dominate the effective mass with the first 8 modes capturing over 90% of the cumulative effective mass. Overall, the results demonstrate stable thermal performance, limited deformation, low stress, and controlled vibrations, confirming the modeling approach and the suitability of 42CrMo4 steel for high-precision ball screw assemblies.
Open AccessThermo-Structural and Dynamic Performance Analysis of a 42CrMo4 Steel Ball Screw Assembly
This study presents a comprehensive thermo-structural and modal analysis of a ball screw assembly. Thermal analysis revealed a maximum temperature of 29.1 °C at the ball nut, corresponding to a total rise of 7.1 °C above ambient. The resulting thermal deformation reached 77.81 μm, while the von Mises stress peaked at 53.9 MPa, both within acceptable limits. Modal simulation of 360 modes showed a sharp increase in frequency with mode number and larger deformation patterns at the higher modes. The first two modes dominate the effective mass with the first 8 modes capturing over 90% of the cumulative effective mass. Overall, the results demonstrate stable thermal performance, limited deformation, low stress, and controlled vibrations, confirming the modeling approach and the suitability of 42CrMo4 steel for high-precision ball screw assemblies.
- Open Access
- 29 November 2024
- Published by MDPI AG in Micromachines
- Vol. 15 (12) , 1457
Impact of Conventional and Laser-Assisted Machining on the Microstructure and Mechanical Properties of Ti-Nb-Cr-V-Ni High-Entropy Alloy Fabricated with Directed Energy Deposition
The high-entropy alloy (HEA) has recently attracted significant interest due to its novel alloy design concept and exceptional mechanical properties, which may exhibit either a single or multi-phase structure. Specifically, refractory high-entropy alloys (RHEA) composed of titanium, niobium, and nickel-based HEA demonstrate remarkable mechanical properties at elevated temperatures. Additive manufacturing (AM), specifically Direct Energy Deposition (DED), is efficient in fabricating high-entropy alloys (HEA) owing to its fast-cooling rates, which promote uniform microstructures and reduce defects. This study involved the fabrication of the Ti33Nb28Cr11V11Ni17 (Ti-Nb-Cr-V-Ni) RHEA utilizing DED. Additionally, the post-processing of the fabricated alloy is conducted using conventional machining (CM) and laser-assisted machining (LAM). The results indicate thermal conductivity and specific heat increased, whereas tensile strength reduced with rising temperature. Significant softening was observed above 800 °C, resulting in a considerable decrease in tensile strength. Furthermore, the LAM caused material softening and reduced the cutting force by 60.0% relative to CM. Furthermore, the chemical composition of Ti-Nb-Cr-V-Ni remained unaffected even after post-processing with CM and LAM. The research indicates that post-processing with LAM is essential for developing resilient RHEA for practical use.
- 29 November 2024
- Published by MDPI AG in Micromachines
- Vol. 15 (12) , 1457
Open AccessImpact of Conventional and Laser-Assisted Machining on the Microstructure and Mechanical Properties of Ti-Nb-Cr-V-Ni High-Entropy Alloy Fabricated with Directed Energy Deposition
The high-entropy alloy (HEA) has recently attracted significant interest due to its novel alloy design concept and exceptional mechanical properties, which may exhibit either a single or multi-phase structure. Specifically, refractory high-entropy alloys (RHEA) composed of titanium, niobium, and nickel-based HEA demonstrate remarkable mechanical properties at elevated temperatures. Additive manufacturing (AM), specifically Direct Energy Deposition (DED), is efficient in fabricating high-entropy alloys (HEA) owing to its fast-cooling rates, which promote uniform microstructures and reduce defects. This study involved the fabrication of the Ti33Nb28Cr11V11Ni17 (Ti-Nb-Cr-V-Ni) RHEA utilizing DED. Additionally, the post-processing of the fabricated alloy is conducted using conventional machining (CM) and laser-assisted machining (LAM). The results indicate thermal conductivity and specific heat increased, whereas tensile strength reduced with rising temperature. Significant softening was observed above 800 °C, resulting in a considerable decrease in tensile strength. Furthermore, the LAM caused material softening and reduced the cutting force by 60.0% relative to CM. Furthermore, the chemical composition of Ti-Nb-Cr-V-Ni remained unaffected even after post-processing with CM and LAM. The research indicates that post-processing with LAM is essential for developing resilient RHEA for practical use.
- Open Access
- 27 September 2024
- Published by MDPI AG in Micromachines
- Vol. 15 (10) , 1196
Effects of Mo Addition on Microstructure and Corrosion Resistance of Cr25-xCo25Ni25Fe25Mox High-Entropy Alloys via Directed Energy Deposition
Highly entropy alloys (HEAs) are novel materials that have great potential for application in aerospace and marine engineering due to their superior mechanical properties and benefits over conventional materials. NiCrCoFe, also referred to as Ni-based HEA, has exceptional low-temperature strength and microstructural stability. However, HEAs have limited corrosion resistance in some environments, such as a 3.5 wt% sodium chloride (NaCl) solution. Adding corrosion-resistant elements such as molybdenum (Mo) to HEAs is expected to increase their corrosion resistance in a variety of corrosive environments. Metal additive manufacturing reduces production times compared to casting and eliminates shrinkage issues, making it ideal for producing homogeneous HEA. This study used directed energy deposition (DED) to create Cr25-xCo25Ni25Fe25Mox (x = 0, 5, 10%) HEAs. Tensile strength and potentiodynamic polarization tests were used to assess the materials’ mechanical properties and corrosion resistance. The mechanical tests revealed that adding 5% Mo increased yield strength (YS) by 20.1% and ultimate tensile strength (UTS) by 9.5% when compared to 0% Mo. Adding 10% Mo led to a 32.5% increase in YS and a 20.4% increase in UTS. Potentiodynamic polarization tests were used to assess corrosion resistance in a 3.5-weight percent NaCl solution. The results showed that adding Mo significantly increased initial corrosion resistance. The alloy with 5% Mo had a higher corrosion potential (Ecorr) and a lower current density (Icorr) than the alloy with 0% Mo, indicating improved initial corrosion resistance. The alloy containing 10% Mo had the highest corrosion potential and the lowest current density, indicating the slowest corrosion rate and the best initial corrosion resistance. Finally, Cr25-xCo25Ni25Fe25Mox (x = 0, 5, 10%) HEAs produced by DED exhibited excellent mechanical properties and corrosion resistance, which can be attributed to the presence of Mo.
- 27 September 2024
- Published by MDPI AG in Micromachines
- Vol. 15 (10) , 1196
Open AccessEffects of Mo Addition on Microstructure and Corrosion Resistance of Cr25-xCo25Ni25Fe25Mox High-Entropy Alloys via Directed Energy Deposition
Highly entropy alloys (HEAs) are novel materials that have great potential for application in aerospace and marine engineering due to their superior mechanical properties and benefits over conventional materials. NiCrCoFe, also referred to as Ni-based HEA, has exceptional low-temperature strength and microstructural stability. However, HEAs have limited corrosion resistance in some environments, such as a 3.5 wt% sodium chloride (NaCl) solution. Adding corrosion-resistant elements such as molybdenum (Mo) to HEAs is expected to increase their corrosion resistance in a variety of corrosive environments. Metal additive manufacturing reduces production times compared to casting and eliminates shrinkage issues, making it ideal for producing homogeneous HEA. This study used directed energy deposition (DED) to create Cr25-xCo25Ni25Fe25Mox (x = 0, 5, 10%) HEAs. Tensile strength and potentiodynamic polarization tests were used to assess the materials’ mechanical properties and corrosion resistance. The mechanical tests revealed that adding 5% Mo increased yield strength (YS) by 20.1% and ultimate tensile strength (UTS) by 9.5% when compared to 0% Mo. Adding 10% Mo led to a 32.5% increase in YS and a 20.4% increase in UTS. Potentiodynamic polarization tests were used to assess corrosion resistance in a 3.5-weight percent NaCl solution. The results showed that adding Mo significantly increased initial corrosion resistance. The alloy with 5% Mo had a higher corrosion potential (Ecorr) and a lower current density (Icorr) than the alloy with 0% Mo, indicating improved initial corrosion resistance. The alloy containing 10% Mo had the highest corrosion potential and the lowest current density, indicating the slowest corrosion rate and the best initial corrosion resistance. Finally, Cr25-xCo25Ni25Fe25Mox (x = 0, 5, 10%) HEAs produced by DED exhibited excellent mechanical properties and corrosion resistance, which can be attributed to the presence of Mo.
- Open Access
- 22 September 2024
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 8 (5) , 206
Optimizing High-Performance Predictive Modeling of the Medium-Speed WEDM Processing of Inconel 718
The purpose of this research was to create a predictive model for a medium-speed wire electrical discharge machine (WEDM) utilizing an artificial neural network (ANN). Medium-speed WEDM experiments were developed based on the I-optimal mixture design for machining, the Inconel 718 superalloy. During the experiment, the input parameters were the spark ontime, spark offtime, wire feed, and current, with the material removal rate (MRR) and surface roughness (Ra) selected as performance indicators. The ANN model was trained on experimental data and built using a feed-forward backpropagation neural network with a (4-8-2) structure and the Bayesian regularization (BR) learning approach. The model correctly predicted the relationship between the medium-speed WEDM’s primary process parameters and machining performance. An integrated ANN model and the Non-Dominated Sorting Genetic Algorithm-II (NSGA-II) were used to determine the ideal parameters for the MRR and Ra, resulting in a set of Pareto-optimal solutions. The confirmation experiment revealed that the mean prediction error between the experimental and ideal solutions had a maximum error percentage of 1% for the MRR and 2% for the Ra, which are within acceptable ranges. This showed that the best process–parameter combinations were better for the MRR and Ra.
- 22 September 2024
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 8 (5) , 206
Open AccessOptimizing High-Performance Predictive Modeling of the Medium-Speed WEDM Processing of Inconel 718
The purpose of this research was to create a predictive model for a medium-speed wire electrical discharge machine (WEDM) utilizing an artificial neural network (ANN). Medium-speed WEDM experiments were developed based on the I-optimal mixture design for machining, the Inconel 718 superalloy. During the experiment, the input parameters were the spark ontime, spark offtime, wire feed, and current, with the material removal rate (MRR) and surface roughness (Ra) selected as performance indicators. The ANN model was trained on experimental data and built using a feed-forward backpropagation neural network with a (4-8-2) structure and the Bayesian regularization (BR) learning approach. The model correctly predicted the relationship between the medium-speed WEDM’s primary process parameters and machining performance. An integrated ANN model and the Non-Dominated Sorting Genetic Algorithm-II (NSGA-II) were used to determine the ideal parameters for the MRR and Ra, resulting in a set of Pareto-optimal solutions. The confirmation experiment revealed that the mean prediction error between the experimental and ideal solutions had a maximum error percentage of 1% for the MRR and 2% for the Ra, which are within acceptable ranges. This showed that the best process–parameter combinations were better for the MRR and Ra.
- Open Access
- 13 September 2023
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 129 (1-2) , 299-319
Integrating experimental modeling techniques with the Pareto search algorithm for multiobjective optimization in the WEDM of Inconel 718
Inconel 718 is a superalloy with a high nickel content that is widely used in applications requiring solid mechanical behavior and resistance to oxidation and corrosion at high temperatures. This alloy has numerous applications in manufacturing steam turbine and jet aircraft interiors, aviation sector manifolds, and rotary spindles. It can be classified as a difficult-to-cut material unsuitable for traditional machining. The purpose of this paper is to develop prediction models for a wire electrical discharge machining (WEDM) process using response surface methodology (RSM), artificial neural networks (ANN), and adaptive neuro-fuzzy inference systems (ANFIS) and to determine which model is better at making accurate predictions. Pulse_ontime, pulse_offtime, servo voltage, flushing pressure, and wire feed were considered the main factors affecting volumetric material removal rate (VMRR) and arithmetic surface roughness (Ra), which were evaluated as WEDM performance characteristics. I-optimal design made with a computer algorithm was employed to develop experimental models. The results reveal that the wire feed and pulse_ontime were the most vital factors influencing VMRR, respectively, and the most significant factor influencing Ra is the pulse_ontime. The total percentage error of the three models demonstrated that the ANN and ANFIS models are more reliable and accurate than the RSM mathematical model. Finally, multiobjective optimization using the Pareto search algorithm was used to optimize mathematical, ANN, and ANFIS models to determine the optimum WEDM process parameters for machining Inconel 718 superalloy.
- 13 September 2023
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 129 (1-2) , 299-319
Open AccessIntegrating experimental modeling techniques with the Pareto search algorithm for multiobjective optimization in the WEDM of Inconel 718
Inconel 718 is a superalloy with a high nickel content that is widely used in applications requiring solid mechanical behavior and resistance to oxidation and corrosion at high temperatures. This alloy has numerous applications in manufacturing steam turbine and jet aircraft interiors, aviation sector manifolds, and rotary spindles. It can be classified as a difficult-to-cut material unsuitable for traditional machining. The purpose of this paper is to develop prediction models for a wire electrical discharge machining (WEDM) process using response surface methodology (RSM), artificial neural networks (ANN), and adaptive neuro-fuzzy inference systems (ANFIS) and to determine which model is better at making accurate predictions. Pulse_ontime, pulse_offtime, servo voltage, flushing pressure, and wire feed were considered the main factors affecting volumetric material removal rate (VMRR) and arithmetic surface roughness (Ra), which were evaluated as WEDM performance characteristics. I-optimal design made with a computer algorithm was employed to develop experimental models. The results reveal that the wire feed and pulse_ontime were the most vital factors influencing VMRR, respectively, and the most significant factor influencing Ra is the pulse_ontime. The total percentage error of the three models demonstrated that the ANN and ANFIS models are more reliable and accurate than the RSM mathematical model. Finally, multiobjective optimization using the Pareto search algorithm was used to optimize mathematical, ANN, and ANFIS models to determine the optimum WEDM process parameters for machining Inconel 718 superalloy.
- Open Access
- 30 May 2023
- Published by Springer Nature in Research Square
Multi-response optimization of Mathematical, ANN, and ANFIS models using the Pareto search algorithm in combination with the I-optimal design of mixture experiments for WEDM of Inconel 718 superalloy
Inconel 718 is a superalloy with a high nickel content that is widely used in applications requiring solid mechanical behavior and resistance to oxidation and corrosion at high temperatures. This alloy has numerous applications in manufacturing steam turbine and jet aircraft interiors, aviation sector manifolds, and rotary spindles. It can be classified as a difficult-to-cut material unsuitable for traditional machining. The purpose of this paper is to develop prediction models for a wire electrical discharge machining (WEDM) process using response surface methodology (RSM), artificial neural networks (ANN), and adaptive neuro-fuzzy inference systems (ANFIS) and to determine which model is better at making accurate predictions. Pulse_ontime, pulse_offtime, servo voltage, flushing pressure, and wire feed were considered the main factors affecting volumetric material removal rate (VMRR) and arithmetic surface roughness (Ra), which were evaluated as WEDM performance characteristics. I-optimal design made with a computer algorithm was employed to develop experimental models. The results reveal that the wire feed and pulse_ontime were the most vital factors influencing VMRR, respectively, and the most significant factor influencing Ra is the pulse_ontime. The total percentage error of the three models demonstrated that the ANN and ANFIS models are more reliable and accurate than the RSM mathematical model. Finally, multi-objective optimization using the Pareto search algorithm was used to optimize mathematical, ANN, and ANFIS models to determine the optimum WEDM process parameters for machining Inconel 718 superalloy.
- 30 May 2023
- Published by Springer Nature in Research Square
Open AccessMulti-response optimization of Mathematical, ANN, and ANFIS models using the Pareto search algorithm in combination with the I-optimal design of mixture experiments for WEDM of Inconel 718 superalloy
Inconel 718 is a superalloy with a high nickel content that is widely used in applications requiring solid mechanical behavior and resistance to oxidation and corrosion at high temperatures. This alloy has numerous applications in manufacturing steam turbine and jet aircraft interiors, aviation sector manifolds, and rotary spindles. It can be classified as a difficult-to-cut material unsuitable for traditional machining. The purpose of this paper is to develop prediction models for a wire electrical discharge machining (WEDM) process using response surface methodology (RSM), artificial neural networks (ANN), and adaptive neuro-fuzzy inference systems (ANFIS) and to determine which model is better at making accurate predictions. Pulse_ontime, pulse_offtime, servo voltage, flushing pressure, and wire feed were considered the main factors affecting volumetric material removal rate (VMRR) and arithmetic surface roughness (Ra), which were evaluated as WEDM performance characteristics. I-optimal design made with a computer algorithm was employed to develop experimental models. The results reveal that the wire feed and pulse_ontime were the most vital factors influencing VMRR, respectively, and the most significant factor influencing Ra is the pulse_ontime. The total percentage error of the three models demonstrated that the ANN and ANFIS models are more reliable and accurate than the RSM mathematical model. Finally, multi-objective optimization using the Pareto search algorithm was used to optimize mathematical, ANN, and ANFIS models to determine the optimum WEDM process parameters for machining Inconel 718 superalloy.