HJHo-In Jeong

Ho-In Jeong

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Ho-In Jeong has a total of 7 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Impact of Conventional and Laser-Assisted Machining on the Microstructure and Mechanical Properties of Ti-Nb-Cr-V-Ni High-Entropy Alloy Fabricated with Directed Energy Deposition

    by Ho-In Jeong, Osama Salem, Dong-Won Jung, Choon-Man Lee, Jeung-Hoon Lee

    The high-entropy alloy (HEA) has recently attracted significant interest due to its novel alloy design concept and exceptional mechanical properties, which may exhibit either a single or multi-phase structure. Specifically, refractory high-entropy alloys (RHEA) composed of titanium, niobium, and nickel-based HEA demonstrate remarkable mechanical properties at elevated temperatures. Additive manufacturing (AM), specifically Direct Energy Deposition (DED), is efficient in fabricating high-entropy alloys (HEA) owing to its fast-cooling rates, which promote uniform microstructures and reduce defects. This study involved the fabrication of the Ti33Nb28Cr11V11Ni17 (Ti-Nb-Cr-V-Ni) RHEA utilizing DED. Additionally, the post-processing of the fabricated alloy is conducted using conventional machining (CM) and laser-assisted machining (LAM). The results indicate thermal conductivity and specific heat increased, whereas tensile strength reduced with rising temperature. Significant softening was observed above 800 °C, resulting in a considerable decrease in tensile strength. Furthermore, the LAM caused material softening and reduced the cutting force by 60.0% relative to CM. Furthermore, the chemical composition of Ti-Nb-Cr-V-Ni remained unaffected even after post-processing with CM and LAM. The research indicates that post-processing with LAM is essential for developing resilient RHEA for practical use.


  • Open Access

    Effects of Mo Addition on Microstructure and Corrosion Resistance of Cr25-xCo25Ni25Fe25Mox High-Entropy Alloys via Directed Energy Deposition

    by Han-Eol Kim, Jae-Hyun Kim, Ho-In Jeong, Young-Tae Cho, Osama Salem, Dong-Won Jung, Choon-Man Lee

    Highly entropy alloys (HEAs) are novel materials that have great potential for application in aerospace and marine engineering due to their superior mechanical properties and benefits over conventional materials. NiCrCoFe, also referred to as Ni-based HEA, has exceptional low-temperature strength and microstructural stability. However, HEAs have limited corrosion resistance in some environments, such as a 3.5 wt% sodium chloride (NaCl) solution. Adding corrosion-resistant elements such as molybdenum (Mo) to HEAs is expected to increase their corrosion resistance in a variety of corrosive environments. Metal additive manufacturing reduces production times compared to casting and eliminates shrinkage issues, making it ideal for producing homogeneous HEA. This study used directed energy deposition (DED) to create Cr25-xCo25Ni25Fe25Mox (x = 0, 5, 10%) HEAs. Tensile strength and potentiodynamic polarization tests were used to assess the materials’ mechanical properties and corrosion resistance. The mechanical tests revealed that adding 5% Mo increased yield strength (YS) by 20.1% and ultimate tensile strength (UTS) by 9.5% when compared to 0% Mo. Adding 10% Mo led to a 32.5% increase in YS and a 20.4% increase in UTS. Potentiodynamic polarization tests were used to assess corrosion resistance in a 3.5-weight percent NaCl solution. The results showed that adding Mo significantly increased initial corrosion resistance. The alloy with 5% Mo had a higher corrosion potential (Ecorr) and a lower current density (Icorr) than the alloy with 0% Mo, indicating improved initial corrosion resistance. The alloy containing 10% Mo had the highest corrosion potential and the lowest current density, indicating the slowest corrosion rate and the best initial corrosion resistance. Finally, Cr25-xCo25Ni25Fe25Mox (x = 0, 5, 10%) HEAs produced by DED exhibited excellent mechanical properties and corrosion resistance, which can be attributed to the presence of Mo.


  • Open Access

    Manufacturing of Ni-Co-Fe-Cr-Al-Ti High-Entropy Alloy Using Directed Energy Deposition and Evaluation of Its Microstructure, Tensile Strength, and Microhardness

    by Ho-In Jeong, Jae-Hyun Kim, Choon-Man Lee

    High-entropy alloys (HEAs) have drawn significant attention due to their unique design and superior mechanical properties. Comprising 5–35 at% of five or more elements with similar atomic radii, HEAs exhibit high configurational entropy, resulting in single-phase solid solutions rather than intermetallic compounds. Additive manufacturing (AM), particularly direct energy deposition (DED), is effective for producing HEAs due to its rapid cooling rates, which ensure uniform microstructures and minimize defects. These alloys typically form face-centered cubic (FCC) or body-centered cubic (BCC) structures, contributing to their exceptional strength, hardness, and mechanical performance across various temperatures. However, FCC-structured HEAs often have low yield strengths, posing a challenge for structural applications. In this study, a Ni-Co-Fe-Cr-Al-Ti HEA was manufactured using the DED method. This study proposes that the addition of aluminum and titanium creates a γ + γ′ phase structure within a multicomponent FCC-HEA matrix, enhancing the thermal stability and coarsening the resistance and strength. The γ′ phase with an ordered FCC structure significantly improves the mechanical properties. Analysis confirmed the presence of the γ + γ′ structure and demonstrated the alloy’s high tensile strength and microhardness. This approach underscores the potential of AM techniques in advancing HEA production for high-performance applications.