Manxin Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Manxin Li has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Ahmed ElShater
Department of Electrical Engineering and Computer Science (EECS), Oregon State University, Corvallis, OR, USA
1 shared publication - Calvin Yoji Lee
Department of Electrical Engineering and Computer Science (EECS), Oregon State University, Corvallis, OR, USA
1 shared publication - Chia-Hung Chen
Department of Electronics and Electrical Engineering, National Yang Ming Chiao Tung University (NYCU), R.O.C, Hsinchu, Taiwan
1 shared publication Ching-Ju Lu
National Yang Ming Chiao Tung University (NYCU) R.O.C
1 shared publication- Fan Ye
Fudan University
1 shared publication - Gabor C. Temes
School of Electrical Engineering and Computer Science, Oregon State University, Corvallis, OR, USA
1 shared publication
Latest Publications
- 13 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 58 (12) , 3555-3564
A Rail-to-Rail 12 MS/s 91.3 dB SNDR 94.1 dB DR Two-Step SAR ADC With Integrated Input Buffer Using Predictive Level-Shifting
Input buffers can be used to reduce the input load of high-resolution discrete-time (DT) Nyquist analog-to-digital converters (ADCs), which can be challenging to drive, particularly at high sampling rates, because of the large input sampling capacitance needed to reduce thermal noise. An input driving technique called predictive level-shifting is proposed to drive rail-to-rail signal swing without increasing the buffer supply rail for high linearity. This article demonstrates an easy-to-drive two-step successive approximation register (SAR) ADC with integrated input buffer, achieving 91.3 dB peak signal-to-noise-and-distortion ratio (SNDR) and 94.1 dB dynamic range (DR) with 6.6 V peak-to-peak differential signal swing and 4 MHz input frequency at 12 MS/s with 30.41 mW power consumption, demonstrating the best performance among the published literature.
- 13 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 58 (12) , 3555-3564
A Rail-to-Rail 12 MS/s 91.3 dB SNDR 94.1 dB DR Two-Step SAR ADC With Integrated Input Buffer Using Predictive Level-Shifting
Input buffers can be used to reduce the input load of high-resolution discrete-time (DT) Nyquist analog-to-digital converters (ADCs), which can be challenging to drive, particularly at high sampling rates, because of the large input sampling capacitance needed to reduce thermal noise. An input driving technique called predictive level-shifting is proposed to drive rail-to-rail signal swing without increasing the buffer supply rail for high linearity. This article demonstrates an easy-to-drive two-step successive approximation register (SAR) ADC with integrated input buffer, achieving 91.3 dB peak signal-to-noise-and-distortion ratio (SNDR) and 94.1 dB dynamic range (DR) with 6.6 V peak-to-peak differential signal swing and 4 MHz input frequency at 12 MS/s with 30.41 mW power consumption, demonstrating the best performance among the published literature.
- 1 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 835-838
A 12bit asynchronous SAR-incremental sub-range ADC
This paper presents a 12-bit asynchronous SAR-incremental sub-range ADC design in 65nm TSMC technology. The combination of power-efficient SAR ADC and low-speed high-accuracy incremental ADC can achieve higher accuracy and relatively high frequency. And the merge of the two architectures can save large amount of area, say, 7/8 the capacitor area of the conventional SAR ADC architecture for the same resolution. At a 1.2-V supply and 62.5MS/s, the simulation results show that the ADC achieves an effective-number-of-bits(ENOB) of 11.6 and consumes 1.6 mW, resulting a figure-of-merit(FOM) of 8.25 fJ/conv-step.
- 1 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 835-838
A 12bit asynchronous SAR-incremental sub-range ADC
This paper presents a 12-bit asynchronous SAR-incremental sub-range ADC design in 65nm TSMC technology. The combination of power-efficient SAR ADC and low-speed high-accuracy incremental ADC can achieve higher accuracy and relatively high frequency. And the merge of the two architectures can save large amount of area, say, 7/8 the capacitor area of the conventional SAR ADC architecture for the same resolution. At a 1.2-V supply and 62.5MS/s, the simulation results show that the ADC achieves an effective-number-of-bits(ENOB) of 11.6 and consumes 1.6 mW, resulting a figure-of-merit(FOM) of 8.25 fJ/conv-step.