Gerhard Wachutka
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Gerhard Wachutka has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
F. Hille
Infineon Technologies AG, Neubiberg, Germany
2 shared publicationsF. Pfirsch
Infineon Technologies AG, Am Campeon 1-12, D-85579 Neubiberg, Germany
2 shared publications- Hesham Okeil
Department of Electrical Engineering, TUM School of Computation, Information and Technology, Technical University of Munich, Munich, Germany
2 shared publications A. Hartl
Infineon Technologies AG, Neubiberg, Germany
1 shared publicationB. Lechner
Chair for Physics of Electro technology, Technical University of Munich, Arcisstrasse 21, Munich, 80333, Germany
1 shared publicationC. Sandow
Infineon Technologies AG, Am Campeon 1-12, D-85579 Neubiberg, Germany
1 shared publication
Latest Publications
- Open Access
- 27 March 2024
- Published by Wiley in Advanced Electronic Materials
- Vol. 10 (5) , 2300531
Very High In‐Plane Magnetic Field Sensitivity in Ion‐Implanted 4H‐SiC PIN Diodes
In this study ion‐implanted lateral 4H‐SiC pin diodes are reported, which show an unexpectedly high room temperature in‐plane magnetic field sensitivity approaching 100 % at 0.5 Tesla. Using dedicated TCAD simulations the underlying transduction mechanism is studied, and the effect of implantation‐induced carrier traps on the observed high sensitivity is unraveled. The study shows how such traps can greatly control the injection conditions at the highly doped implant regions providing a plausible explanation for an observed portion in the IV‐characteristics of the pin diodes exhibiting the aforementioned high magnetic field sensitivity.
- 27 March 2024
- Published by Wiley in Advanced Electronic Materials
- Vol. 10 (5) , 2300531
Open AccessVery High In‐Plane Magnetic Field Sensitivity in Ion‐Implanted 4H‐SiC PIN Diodes
In this study ion‐implanted lateral 4H‐SiC pin diodes are reported, which show an unexpectedly high room temperature in‐plane magnetic field sensitivity approaching 100 % at 0.5 Tesla. Using dedicated TCAD simulations the underlying transduction mechanism is studied, and the effect of implantation‐induced carrier traps on the observed high sensitivity is unraveled. The study shows how such traps can greatly control the injection conditions at the highly doped implant regions providing a plausible explanation for an observed portion in the IV‐characteristics of the pin diodes exhibiting the aforementioned high magnetic field sensitivity.
- 14 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 72 (00189456) , 1-8
High-Throughput Apparatus for Semiconductor Device Characterization in a Magnetic Field at Extreme High Temperatures
We report on the development of a 600 °C withstanding low-noise apparatus, which enables high throughput magnetic field dependent characterization of semiconductor devices bonded to a ceramic substrate at very high temperatures. A novel and simple method for electrically contacting metal pads on the ceramic substrate is developed, which allows contacting many metal pads simultaneously on limited space. The apparatus can be used for a variety of high temperature experiments such as studying galvanomagnetic transport effects in devices and the characterization of SiC or GaN magnetic field sensors at very high temperatures. Furthermore, it can be used for performing very high temperature die attach processes. The apparatus has been successfully used to resolve magnetic field dependent current changes in a SiC pn diode ranging into the ppm scale at 500 °C.
- 14 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 72 (00189456) , 1-8
High-Throughput Apparatus for Semiconductor Device Characterization in a Magnetic Field at Extreme High Temperatures
We report on the development of a 600 °C withstanding low-noise apparatus, which enables high throughput magnetic field dependent characterization of semiconductor devices bonded to a ceramic substrate at very high temperatures. A novel and simple method for electrically contacting metal pads on the ceramic substrate is developed, which allows contacting many metal pads simultaneously on limited space. The apparatus can be used for a variety of high temperature experiments such as studying galvanomagnetic transport effects in devices and the characterization of SiC or GaN magnetic field sensors at very high temperatures. Furthermore, it can be used for performing very high temperature die attach processes. The apparatus has been successfully used to resolve magnetic field dependent current changes in a SiC pn diode ranging into the ppm scale at 500 °C.
- 1 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 28, 19-28
High-Fidelity Predictive Simulation of High Power Devices and Modules at the Rim of the Safe-Operating Area and Beyond
The development of high-performance power devices is increasingly supported by predictive computer simulations on the basis of well-calibrated physical device models. Today's challenge is to make virtual experiments and tests on the computer, which are qualitatively reliable and quantitatively accurate even for device structures that have never been built before, and under operational conditions that very rarely occur as long as the device is kept within the “safe operating area (SOA)”. What we are interested in is to explore the rim of the SOA and even to go beyond it in order to study failure and, eventually, destruction mechanisms with a view to improving robustness and reliability of the devices with respect to a customer-defined “mission profile”. In particular in the field of high power electronics, predictive high-fidelity computer simulations of “virtual desctruction” are of utmost importance. We will illustrate today's state of the art with reference to selected real-life examples.
- 1 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 28, 19-28
High-Fidelity Predictive Simulation of High Power Devices and Modules at the Rim of the Safe-Operating Area and Beyond
The development of high-performance power devices is increasingly supported by predictive computer simulations on the basis of well-calibrated physical device models. Today's challenge is to make virtual experiments and tests on the computer, which are qualitatively reliable and quantitatively accurate even for device structures that have never been built before, and under operational conditions that very rarely occur as long as the device is kept within the “safe operating area (SOA)”. What we are interested in is to explore the rim of the SOA and even to go beyond it in order to study failure and, eventually, destruction mechanisms with a view to improving robustness and reliability of the devices with respect to a customer-defined “mission profile”. In particular in the field of high power electronics, predictive high-fidelity computer simulations of “virtual desctruction” are of utmost importance. We will illustrate today's state of the art with reference to selected real-life examples.
- 1 October 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Impact of the Activation of Carbon Vacancies at High Temperatures on the Minority Carrier Lifetimes in the Intrinsic Area of 4H-SiC PiN Rectifier
The temperature dependent behaviour of a high power 4H-SiC PiN-diode was investigated by the adjustment of measured forward characteristics and quasistatic TCAD simulations in a temperature range from RT up to 773 K. The systematic analysis of the relevant physical parameters for the adjustment of measurements and simulations shows, that the predominating influence originates from the SRH (Shockley-Read-Hall) minority carrier lifetimes in the intrinsic region. The carrier lifetimes exhibit a negative temperature coefficient for temperatures above 673 K that disagrees with the theoretical models of the temperature dependence of the SRH recombination caused by just one effective type of impurity. The EH6/7 centers are the most promising candidates for additional recombination centers that become activated at higher temperatures and cause an increase in non-radiative carrier recombination that leads to decreasing SRH carrier lifetime.
- 1 October 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Impact of the Activation of Carbon Vacancies at High Temperatures on the Minority Carrier Lifetimes in the Intrinsic Area of 4H-SiC PiN Rectifier
The temperature dependent behaviour of a high power 4H-SiC PiN-diode was investigated by the adjustment of measured forward characteristics and quasistatic TCAD simulations in a temperature range from RT up to 773 K. The systematic analysis of the relevant physical parameters for the adjustment of measurements and simulations shows, that the predominating influence originates from the SRH (Shockley-Read-Hall) minority carrier lifetimes in the intrinsic region. The carrier lifetimes exhibit a negative temperature coefficient for temperatures above 673 K that disagrees with the theoretical models of the temperature dependence of the SRH recombination caused by just one effective type of impurity. The EH6/7 centers are the most promising candidates for additional recombination centers that become activated at higher temperatures and cause an increase in non-radiative carrier recombination that leads to decreasing SRH carrier lifetime.
- 1 June 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 10636854,p. 135-138
Evolution of current filaments limiting the safe-operating area of high-voltage trench-IGBTs
An improved understanding of the physical processes leading to the formation of current filaments and latch-up in large arrays of monolithically integrated high voltage (3.3kV) trench-IGBT cells during the turn-off process of the device is the prerequisite for enhancing the robustness of the device. To this end, numerical simulations have been performed revealing the rim of the safe-operating area (SOA) and what happens beyond it.
- 1 June 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 10636854,p. 135-138
Evolution of current filaments limiting the safe-operating area of high-voltage trench-IGBTs
An improved understanding of the physical processes leading to the formation of current filaments and latch-up in large arrays of monolithically integrated high voltage (3.3kV) trench-IGBT cells during the turn-off process of the device is the prerequisite for enhancing the robustness of the device. To this end, numerical simulations have been performed revealing the rim of the safe-operating area (SOA) and what happens beyond it.
- 1 September 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 29, LS2e.3-1-LS2e.3-5
Predictive physical model of cosmic-radiation-induced failures of power devices
In the last ten years, the hardening of silicon high power devices against cosmic-radiation-induced failure gained decisive importance. A systematic improvement of the robustness against cosmic radiation requires a fundamental physical understanding of the microscopic mechanisms which lead to the failure or even destruction of power devices. We performed detailed 3D thermo-electrical device simulations to study the local self-heating in the device in order to explain the failure and destruction mechanisms and compared the results with experimental data obtained from nucleon irradiation experiments. Several diode designs with varying doping concentration and vertical size of the device were investigated.
- 1 September 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 29, LS2e.3-1-LS2e.3-5
Predictive physical model of cosmic-radiation-induced failures of power devices
In the last ten years, the hardening of silicon high power devices against cosmic-radiation-induced failure gained decisive importance. A systematic improvement of the robustness against cosmic radiation requires a fundamental physical understanding of the microscopic mechanisms which lead to the failure or even destruction of power devices. We performed detailed 3D thermo-electrical device simulations to study the local self-heating in the device in order to explain the failure and destruction mechanisms and compared the results with experimental data obtained from nucleon irradiation experiments. Several diode designs with varying doping concentration and vertical size of the device were investigated.
- 1 December 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
Physical modeling of SiC devices based on the optical characterization of their internal electrothermal behavior
While the material and process technologies for SiC devices are becoming steadily more mature, the predictive simulation of SiC devices still lacks the availability of accurately calibrated physical device models. Basically it is feasible to adopt the physical models describing silicon devices for the analysis of SiC devices, but it is indispensable to recalibrate the model parameters. A reliable calibration requires measured and simulated data that can be one-to-one related to each other. But while experimental data mostly refer to the terminal behavior of the device under test, simulations can also provide insight into the "innerelectronic" behavior. In view of the device physics underlying the electrothermal behavior of devices, the spaceand time-resolved electron and hole concentrations as well as the temperature distribution are among the most interesting quantities. This paper presents an optical diagnosis method that combines free carrier absorption measurements, which yield time-resolved electron and hole density profiles from bipolar devices during turn-on and under stationary conditions, and light deflection measurements, which provide information about the gradients of the electron and hole densities as well as that of the temperature gradient. The measurement and the model calibration are exemplified by considering samples of 4H-SiC 6.5 kV bipolar diodes with a thickness of the intrinsic region of 70 ¿m. In particular, the calibration is focused on the physical models of incomplete ionization of dopants, carrier mobility, and Shockley-Read-Hall recombination.
- 1 December 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
Physical modeling of SiC devices based on the optical characterization of their internal electrothermal behavior
While the material and process technologies for SiC devices are becoming steadily more mature, the predictive simulation of SiC devices still lacks the availability of accurately calibrated physical device models. Basically it is feasible to adopt the physical models describing silicon devices for the analysis of SiC devices, but it is indispensable to recalibrate the model parameters. A reliable calibration requires measured and simulated data that can be one-to-one related to each other. But while experimental data mostly refer to the terminal behavior of the device under test, simulations can also provide insight into the "innerelectronic" behavior. In view of the device physics underlying the electrothermal behavior of devices, the spaceand time-resolved electron and hole concentrations as well as the temperature distribution are among the most interesting quantities. This paper presents an optical diagnosis method that combines free carrier absorption measurements, which yield time-resolved electron and hole density profiles from bipolar devices during turn-on and under stationary conditions, and light deflection measurements, which provide information about the gradients of the electron and hole densities as well as that of the temperature gradient. The measurement and the model calibration are exemplified by considering samples of 4H-SiC 6.5 kV bipolar diodes with a thickness of the intrinsic region of 70 ¿m. In particular, the calibration is focused on the physical models of incomplete ionization of dopants, carrier mobility, and Shockley-Read-Hall recombination.
- 1 January 2008
- Published by Institution of Engineering and Technology (IET)
- p. 21-24
Virtual experiments with power devices using predictive simulation
- 1 January 2008
- Published by Institution of Engineering and Technology (IET)
- p. 21-24
Virtual experiments with power devices using predictive simulation
- 13 September 2005
- Published by Springer Nature
- p. 387-394
Domain Decomposition Methods in Electrothermomechanical Coupling Problems
- 13 September 2005
- Published by Springer Nature
- p. 387-394
Domain Decomposition Methods in Electrothermomechanical Coupling Problems
- 7 March 2005
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components and Packaging Technologies
- Vol. 28 (1) , 23-33
Transient temperature fields with general nonlinear boundary conditions in electronic systems
Green's function representations of the solution of the heat conduction equation for general boundary conditions are generalized for the nonlinear, i.e., temperature dependent case. Temperature dependent heat transfer coefficients lead to additional terms in the Green's function representation of the temperature field. For a rectangular structure with averaged homogeneous material parameters several types of Green's functions can be chosen especially simple, because of the new representation with the possibility of differing types of boundary conditions for the temperature field and the Green's function. Exact finite closed form expressions for three-dimensional-Green's functions in the time domain using elliptic theta functions are presented. The temperature field is a solution of a nonlinear integral equation which is solved numerically by iteration. The resulting algorithm is very robust, stable and accurate with reliable convergence properties and avoids matrix inversions completely. The algorithm can deal with all sizes of volume heat sources without additional grid generation. Large and small size volume heat sources are treated simultaneously in the calculations that will be presented. Heat transfer coefficients are chosen representing radiative and convective boundary conditions. An extension of the solution algorithm to composed multilayer systems of arbitrary geometry is outlined.
- 7 March 2005
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components and Packaging Technologies
- Vol. 28 (1) , 23-33
Transient temperature fields with general nonlinear boundary conditions in electronic systems
Green's function representations of the solution of the heat conduction equation for general boundary conditions are generalized for the nonlinear, i.e., temperature dependent case. Temperature dependent heat transfer coefficients lead to additional terms in the Green's function representation of the temperature field. For a rectangular structure with averaged homogeneous material parameters several types of Green's functions can be chosen especially simple, because of the new representation with the possibility of differing types of boundary conditions for the temperature field and the Green's function. Exact finite closed form expressions for three-dimensional-Green's functions in the time domain using elliptic theta functions are presented. The temperature field is a solution of a nonlinear integral equation which is solved numerically by iteration. The resulting algorithm is very robust, stable and accurate with reliable convergence properties and avoids matrix inversions completely. The algorithm can deal with all sizes of volume heat sources without additional grid generation. Large and small size volume heat sources are treated simultaneously in the calculations that will be presented. Heat transfer coefficients are chosen representing radiative and convective boundary conditions. An extension of the solution algorithm to composed multilayer systems of arbitrary geometry is outlined.