Ting Shang
Research Subjects
Ting Shang has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
Bin Gao
Department of Automation Engineering, University of Electronic Science and Technology of China, Chengdu, China
1 shared publication- Ding Liu
Xi’an University of Technology
1 shared publication - Fan Liu
National and Local Engineering Research Center of Crystal Growth Equipment and System Integration
1 shared publication - Jiaming Lv
School of Automation and Information Engineering, Xi’an University of Technology , Xi’an, China
1 shared publication - Jiapei Li
School of Automation and Information Engineering, Xi’an University of Technology , Xi’an, China
1 shared publication Jiaqi Pei
School of Automation and Information Engineering, Xian University of Technology, Xian, China
1 shared publication
Latest Publications
- 1 November 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Control Systems Technology
- Vol. 34 (6) , 3171-3184
Thermal Delay Compensated in Industrial Crystal Furnaces: A Robin Boundary Control for Distributed Parameter Systems
- 1 November 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Control Systems Technology
- Vol. 34 (6) , 3171-3184
Thermal Delay Compensated in Industrial Crystal Furnaces: A Robin Boundary Control for Distributed Parameter Systems
- 31 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (4) , 6414-6424
Prediction of Fatigue Crack Propagation in X80 Pipeline Steel Using Acoustic Emission Sensing
Fatigue cracks in gas pipelines, particularly those constructed from X80 steel, pose significant risks of catastrophic failure if not monitored continuously. This study presents a novel methodology for predicting the Fatigue Crack Propagation Rate (FCPR) of X80 pipeline steel by using Acoustic Emission (AE) sensing technique. Through a series of three-point bending fatigue tests conducted under varying loading conditions, the influence of the stress ratio and maximum load on the fatigue crack propagation behavior of X80 pipeline steel is investigated. Furthermore, the characteristics of AE signals generated during the stable and rapid crack propagation stages has been analyzed. A new AE feature, related to the average AE amplitude rate, is proposed, demonstrating a stronger linear correlation with FCPR than traditional AE feature metrics. Based on this newly proposed AE feature, a predictive model for fatigue crack propagation has been developed, which not only accurately identifies the transition from stable to rapid crack propagation but also offers precise real-time predictions of FCPR, with predictions falling within the 95% confidence interval of measured values. These findings offer a robust framework for real-time structural health monitoring of pipelines, enhancing early intervention strategies and improving safety protocols for critical pipeline infrastructure.
- 31 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (4) , 6414-6424
Prediction of Fatigue Crack Propagation in X80 Pipeline Steel Using Acoustic Emission Sensing
Fatigue cracks in gas pipelines, particularly those constructed from X80 steel, pose significant risks of catastrophic failure if not monitored continuously. This study presents a novel methodology for predicting the Fatigue Crack Propagation Rate (FCPR) of X80 pipeline steel by using Acoustic Emission (AE) sensing technique. Through a series of three-point bending fatigue tests conducted under varying loading conditions, the influence of the stress ratio and maximum load on the fatigue crack propagation behavior of X80 pipeline steel is investigated. Furthermore, the characteristics of AE signals generated during the stable and rapid crack propagation stages has been analyzed. A new AE feature, related to the average AE amplitude rate, is proposed, demonstrating a stronger linear correlation with FCPR than traditional AE feature metrics. Based on this newly proposed AE feature, a predictive model for fatigue crack propagation has been developed, which not only accurately identifies the transition from stable to rapid crack propagation but also offers precise real-time predictions of FCPR, with predictions falling within the 95% confidence interval of measured values. These findings offer a robust framework for real-time structural health monitoring of pipelines, enhancing early intervention strategies and improving safety protocols for critical pipeline infrastructure.
- Open Access
- 1 September 2023
- Published by AIP Publishing in AIP Advances
- Vol. 13 (9)
A fast calibration method for distributed measurement systems
Aiming at the distributed measurement system multi-equipment coordinated measurement, the data measured by each transmitting station are unified under a common coordinate system, which has the problems of complicated operation and high time and cost. In this paper, a fast calibration method for distributed measurement systems based on standard devices is proposed. The method designs a new type of architectural calibration board with non-coplanar measurement nodes, calculates the coordinates of the measurement nodes using geometric relations, solves the initial values of the system parameters, and substitutes the initial values into the L-M least squares algorithm for iterative optimization so that it only needs to carry out one scanning measurement for each reference position in the calibration process to complete the calibration. We designed an experiment in which a distributed measurement system consisting of four transmitting stations measured three standard rods (1650.073, 1156.704, and 875.950 mm) sequentially after calibration in a measuring space of 5 × 5 × 3 m3. The experimental results show that under the premise of ensuring that the measurement accuracy is better than 0.20 mm, the calibration of the parameters of the distributed measurement system can be completed within 20 min.
- 1 September 2023
- Published by AIP Publishing in AIP Advances
- Vol. 13 (9)
Open AccessA fast calibration method for distributed measurement systems
Aiming at the distributed measurement system multi-equipment coordinated measurement, the data measured by each transmitting station are unified under a common coordinate system, which has the problems of complicated operation and high time and cost. In this paper, a fast calibration method for distributed measurement systems based on standard devices is proposed. The method designs a new type of architectural calibration board with non-coplanar measurement nodes, calculates the coordinates of the measurement nodes using geometric relations, solves the initial values of the system parameters, and substitutes the initial values into the L-M least squares algorithm for iterative optimization so that it only needs to carry out one scanning measurement for each reference position in the calibration process to complete the calibration. We designed an experiment in which a distributed measurement system consisting of four transmitting stations measured three standard rods (1650.073, 1156.704, and 875.950 mm) sequentially after calibration in a measuring space of 5 × 5 × 3 m3. The experimental results show that under the premise of ensuring that the measurement accuracy is better than 0.20 mm, the calibration of the parameters of the distributed measurement system can be completed within 20 min.