Arwin Goossens

Organic electrochemical transistors (OECTs) enable the transduction of ionic signals into electronic outputs, positioning them as ideal candidates for next-generation sensing and (bio)signal processing applications. Recent years have witnessed the development of various OECT channel materials, affording insights on structural fine-tuning to achieve optimal performance and/or stability. However, homocouplings, commonly present in alternating conjugated polymers, have largely been overlooked. This study investigates the effect of homocoupling on OECT materials by employing two synthesis methods – standard Stille polymerization and an alternative symmetric approach – to create the p-type enhancement-mode benchmark polymer pgBTTT. The impact of homocoupling, and its absence, is studied by comparing the bulk properties of the two polymers and evaluating their respective OECT metrics. The new, homocoupling-free polymer exhibits a notably improved OECT performance (μC*), mainly due to an increase in electronic mobility (μ), which is attributed to both the perfectly alternating structure and its higher molar mass.

This study reports on the first all‐printed vertically stacked organic electrochemical transistors (OECTs) operating in accumulation mode; the devices, relying on poly([4,4′‐bis(2‐(2‐(2‐methoxyethoxy)ethoxy)ethoxy)‐2,2′‐bithiophen‐5,5′‐diyl]‐alt‐[thieno[3,2‐b]thiophene‐2,5‐diyl]) (pgBTTT) as the active channel material, are fabricated via a combination of screen and inkjet printing technologies. The resulting OECTs (W/L ≈5) demonstrate good switching performance; g_{m, norm} ≈13 mS cm⁻¹, µC* ≈21 F cm⁻¹ V⁻¹ s⁻¹, ON–OFF ratio > 10⁴ and good cycling stability upon continuous operation for 2 h. The inkjet printing process of pgBTTT is established by first solubilizing the polymer in dihydrolevoglucosenone (Cyrene), a non‐toxic, cellulose‐derived, and biodegradable solvent. The resulting ink formulations exhibit good jettability, thereby providing reproducible and stable p‐type accumulation mode all‐printed OECTs with high performance. Besides the environmental and safety benefits of this solvent, this study also demonstrates the assessment of how the solvent affects the performance of spin‐coated OECTs, which justifies the choice of Cyrene as an alternative to commonly used harmful solvents such as chloroform, also from a device perspective. Hence, this approach shows a new possibility of obtaining more sustainable printed electronic devices, which will eventually result in all‐printed OECT‐based logic circuits operating in complementary mode.

The true structure of alternating conjugated polymers—the state‐of‐the‐art materials for many organic electronics—often deviates from the idealized picture. Homocoupling defects are in fact inherent to the widely used cross‐coupling polymerization methods. Nevertheless, many polymers still perform excellently in the envisaged applications, which raises the question if one should really care about these imperfections. This article looks at the relevance of chemical precision (and lack thereof) in conjugated polymers covering the entire spectrum from the molecular scale, to the micro and mesostructure, up to the device level. The different types of polymerization errors for the alkoxylated variant of the benchmark (semi)crystalline polymer poly[2,5‐bis(3‐tetradecylthiophen‐2‐yl)thieno[3,2‐b]thiophene (PBTTT) are identified, visualized, and quantified and a general strategy to avoid homocoupling is introduced. Through a combination of experiments and supported by simulations, it is shown that these coupling defects hinder fullerene intercalation and limit device performance as compared to the homocoupling‐free analog. This clearly demonstrates that structural defects do matter and should be generally avoided, in particular when the geometrical regularity of the polymer is essential. These insights likely go beyond the specific PBTTT derivatives studied here and are of general relevance for the wider organic electronics field.