MDMonsuru Olatunji Dauda

Monsuru Olatunji Dauda

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Monsuru Olatunji Dauda has a total of 49 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Electrolytic Reduction of CO 2 in a Flowing Electrolyte Interlayer MEA Cell

    by Monsuru Olatunji Dauda, Mustapha Bello, John Hendershot, Ignace Agbadan, Nicholas Lombardo, Sohrab Bin Noor, Phillip Sprunger, Koffi Yao, Anthony Christian Engler, John C. Flake

    A Flowing Electrolyte Interlayer (FEI) electrolyzer is demonstrated for CO 2 reduction. The 3-layer cell includes an anion-exchange membrane, a cation-exchange membrane, and a flowing interlayer that serves as a product-collection stream. The new cell was evaluated using copper-based electrocatalysts, including CuSn 0.03 , CuSn 4 , and Cu 2 Se, for the selective production of ethanol and direct recovery of free acid (formic acid or acetic acid). Analyses, including operando ED-XRD and XAS, confirm structural stability of cell components. The FEI electrolyzer retained up to 63% ethanol Faradaic efficiency while enabling direct recovery of liquid products and suppressing anode crossover to below 2%, a more than 40-fold reduction compared with conventional MEA systems. Channel geometry and flow experiments revealed that product removal is limited at relatively low flow velocities and may be diluted at higher velocities. An optimal interlayer channel configuration was shown to deliver up to 9 weight percent ethanol for over 60 h.

  • Pressure Effect on the Electrochemical Reduction of CO to Acetate in MEA

    by Ignace Kodjo Agbadan, Monsuru Olatunji Dauda, John C Hendershot, Omotolani Elizabeth Oduyebo, Cigdem Atalay-Oral, John Flake

    We investigate Cu and Cu2Se electrocatalysts operating at 500 and 750 mA cm-2 across several electrolytes (0.1 M KHCO3, 1 M KOH, and phosphate buffer at pH 8) and pressures ranging from 1 to 3 atm. In general, alkaline electrolytes and higher pressures enhance acetate Faradaic efficiency (FE) while suppressing ethylene, ethanol, formate, and hydrogen evolution. In the 0.1 M KHCO3 electrolyte at 500 mA cm-2, acetate FE increased from 57% to 66% at Cu electrodes and from 70% to 77% on Cu2Se when pressure increased from 1 to 3 atm. When using phosphate-buffered electrolytes (pH 8), acetate FE improved from 50% to 60% on Cu and from 61% to 70% on Cu2Se. Remarkably, Cu2Se showed an FE of 92% to acetate at 750 mA cm-2 in an alkaline electrolyte (1 M KOH) under 3 atm, compared to 61% at atmospheric pressure, with the remaining products being predominantly ethanol (1% FE) and hydrogen (5% FE). Furthermore, the additional pressure allows lower cell potentials, decreasing from 3.51 V at 1 atm to 3.46 V at 3 atm, while hydrogen FE declined from 5.98% to 5.34% (12% relative reduction).

  • Raman Evidence for the Mechanism of Enhanced C-C Coupling During CO2RR on CuSnx Bimetallic Electrocatalysts at Dilute Sn Levels

    by Koffi Yao, Mritunjay P.C. Mishra, Emmanuel Obetta, Monsuru Olatunji Dauda, John Flake

    The electrochemical carbon dioxide reduction reaction (CO2RR) presents a promising method for converting CO2 into valuable fuels and chemicals but require electrocatalysts with high selectivity. Here, we investigate CuSnx catalysts with systematically varied Sn contents to elucidate composition-selectivity relationships. Electrolyzer testing reveals that 3%Sn doped Cu electrocatalyst selectively produces C2 products, primarily ethanol and ethylene, whereas higher Sn contents (>3%) shift selectivity toward C1 products, predominantly formic acid. XPS suggests the coexistence in similar proportions of near neutral (Cu) and partial positive (Cuδ+) sites at low Sn contents. On the other hand, at high Sn contents, surface Cu skews towards monolithically Cu2+ states. From In-situ surface-enhanced Raman spectroscopy, at 3%Sn, abundant *COOH absorbed via carbon is detected that leads to detected high *CO coverage with electrophilicity imbalance from absorbing at Cu and Cuδ+. Two electronically dissimilar *COs then promote *CO*CO dimerization favoring C2 products. At 50% and 80% Sn, HCOO* intermediate adsorbed via oxygen is detected instead, leading to formic acid as the major product upon proton transfer. The findings experimentally corroborate prior computational DFT conclusions and provide empirical insight into the role of Sn doping in tuning the catalytic behavior of Cu for CO2RR.

  • Open Access

    Raman Evidence for the Mechanism of Enhanced C–C Coupling during CO 2 RR on CuSn x Bimetallic Electrocatalysts at Dilute Sn Levels

    by Mritunjay Mishra, Emmanuel Obetta, Monsuru Olatunji Dauda, John Flake, Koffi P. C. Yao

    The electrochemical carbon dioxide reduction reaction (CO 2 RR) presents a promising method for converting CO 2 into valuable fuels and chemicals, but requires electrocatalysts with high selectivity. Here, we investigate CuSn x catalysts with systematically varied Sn contents to elucidate composition-selectivity relationships. Electrolyzer testing reveals that 3%Sn-doped Cu electrocatalyst selectively produces C 2 products, primarily ethanol and ethylene, whereas higher Sn contents (>3%) shift selectivity toward C 1 products, predominantly formic acid. X-ray photoelectron spectroscopy suggests the coexistence in similar proportions of near neutral (Cu) and partial positive (Cu δ + ) sites at low Sn contents. On the other hand, at high Sn contents, surface Cu skews towards monolithically Cu 2+ states. From In-situ surface-enhanced Raman spectroscopy, at 3%Sn, abundant *COOH absorbed via carbon is detected that leads to detected high *CO coverage with electrophilicity imbalance from absorbing at Cu and Cu δ + . Two electronically dissimilar *COs then promote *CO*CO dimerization favoring C 2 products. At 50% and 80% Sn, HCOO* intermediate adsorbed via oxygen is detected instead, leading to formic acid as the major product upon proton transfer. The findings experimentally validate prior computational density functional theory conclusions and provide empirical insight into the role of Sn doping in tuning the catalytic behavior of Cu for CO 2 RR.


  • Molecular Electrocatalyst (Cu-based composite) for the Electrochemical Reduction of CO 2 in Membrane Electrode Assemblies

    by Ignace Kodjo Agbadan, Julie Jannise, Monsuru Olatunji Dauda, Mustapha Bello, John C Hendershot, Vaeda Trudeau Hobbs, Omotolani Elizabeth Oduyebo, Cigdem Atalay Atalay-Oral, Noemie Elgrishi, John Flake

    The electrochemical reduction of CO 2 to ethanol, acetate and formate provides a circular pathway for carbon products, fuels, and food; however, achievingefficient C-C coupling remains a challenge. Molecular electrocatalysts typically generate single-carbon products, while copper catalysts promote C-C coupling but typically produces a broad spectrum of C 1 and C 2+ products. Herein, we report an established cooperative molecule-metal interface by functionalizing copper with porphyrin complexes and cobalt phthalocyanine (CoPh) that reduce CO 2 to CO, enriching the local reaction environment. With the molecular electrocatalysts yielding maximum CO (87% Faradaic efficiencies; FE CO ) at a low cell potential of 2.97 V, a cascade reaction (CO 2 - CO - C 1 or C 2+ ) on Cu-molecule composite electrocatalyst achieves a shift in catalytic behavior, to oxygenates with FE up to 41% for ethanol at a cell potential of 3.47 V, 36% formate at a cell potential of 3.3 V and an overall C 2+ products increment of 59% at a cell potential of 3.47 V and 63% at a cell potential of 3.7 V on Cu with iron (III) tetra-trimethylanilinium porphyrin pentachloride (FeTMAPP) and Cu with iron (III) tetra-(4-sulfonatophenyl) porphyrin Chloride (FeTPP) respectively. Similarly, 32% and 43% FE increment for the oxygenated products were observed on Cu 2 Se-FeTMAPP and Cu 2 Se-CoPh at a cell potential of 3.47 V and 3.54 V respectively with acetate (50% FE at 3.47 V) and formate (52% FE at 3.3 V) as the primary products. The selectivity shift is likely related to changes in the electrode-electrolyte interface. We show the effect of co-feeding CO and demonstrate the role of the molecular electrocatalyst.

  • Tailoring the Local Environment for Electrochemical Reduction of CO₂ to Ethylene

    by Monsuru Olatunji Dauda, Mustapha Bello, John C Hendershot, Ignace Kodjo Agbadan, Soundarzo Tasnim, Omotolani Elizabeth Oduyebo, John Flake

    Ethylene, a petrochemical feedstock exceeding 200 million tons annual demand, is traditionally produced through energy-intensive steam cracking that emits 0.85–1.8 tons CO₂ per ton of product. Electrochemical CO₂ reduction offers a greener alternative, though achieving high selectivity of ethylene remains a huge challenge due to the numerous possible reaction pathways. Here, we explore our findings on electrochemical CO₂ reduction using Cu-P electrocatalysts in weakly acidic environments, where pH 6 conditions provide balance between CO₂ activation and hydrogen evolution in our membrane electrode assembly system (Fig. 1A), achieving remarkable Faradaic efficiencies of 72.84% for ethylene at 300 mA cm⁻² and 51.42% at 500 mA cm⁻², alongside 51% single-pass CO₂ conversion efficiency (Fig. 1B). Our pH-dependent studies illustrate a shift in product selectivity from mixed C₂ products under alkaline conditions to predominantly ethylene in weakly acidic environments (Fig. 1C). Importantly, our research reveals product selectivity is controlled by pH and cation identity, with mechanistic investigations showing how pH-dependent CO coverage alters the competition between ethylene and ethanol formation pathways. Cu-P electrocatalysts maintain stability over 400 hours, positioning our work favorably against previous reports (Fig. 1D). These insights provide crucial guidance for developing high-performance electrocatalytic systems for targeted C₂ product formation, advancing sustainable approaches to address global carbon challenges. Figure 1

  • Physical and Chemical Durability of Anion Exchange Membranes Used in the Electrochemical Reduction of CO 2

    by Soundarzo Tasnim, Ignace Kodjo Agbadan, Monsuru Olatunji Dauda, John C Hendershot, Mustapha Bello, Junghyun Park, Omotolani Elizabeth Oduyebo, Cigdem Atalay Atalay-Oral, John Flake

    Membrane electrode assemblies (MEA) benefit from high current densities and FEs in the electrocatalytic CO 2 reduction reaction (CO 2 RR). However, membrane durability remains a challenge for industrial use. The aim of this study is to investigate the degradation mechanisms of three anion exchange membranes (AEMs) using 0.1M KHCO₃ electrolyte over a 250-hour CO 2 reduction period at 150 mA cm -2 . Three AEM materials were considered: FAA-3-50 (Fumatech), PiperION (Versogen), and Sustainion X37-50 (Dioxide Materials). Ex-situ investigations were carried out using techniques such as tensile testing, Attenuated Total Reflectance Fourier Transform Infrared Spectroscopy (ATR-FTIR), and Electrochemical Impedance Spectroscopy (EIS) to evaluate chemical, electrical, and mechanical deterioration. Despite the use of the same near-nuetral KHCO 3 electrolytes, ATR-FTIR analysis showed different degradation patterns: nucleophilic substitution in FAA-3-50, Hoffman elimination in PiperION, and hydroxide-induced imidazolium breakage in Sustainion. According to EIS studies, the observed variation in ohmic resistance led to steady increases in cell potential increases from approximately 3.5 to 4.8 V at a current density of 150 mA cm -2 . HCO 3 ⁻ conductivity decreased by approximately 50% in the 250 hours of operation. Significant losses in mechanical integrity were also observed, including Young's modulus losses of 46% (FAA-3-50), 18% (PiperION), and 78% (Sustainion). The most notable increase in deformation at break was observed in Sustainion, which went from 4.8% to 20.46%, indicating a higher susceptibility to mechanical wear under prolonged use. This study shows that alkaline conditions in CO 2 reduction (including high local pH conditions near the cathode) cause AEM degradation, which in turn contributes to increases in cell potentials ranging from about 400 mV to 800 mV within several hundred hours of electrolysis at current densities in the range of 100 to 300 mA cm -2 .

  • (IE&EE Student Achievement Award) Strategies for Sustainable Ethylene, Ethanol, and Acetate via Electrochemical CO₂ Reduction

    by Monsuru Olatunji Dauda, Mustapha Bello, John C Hendershot, Junghyun Park, Ignace Kodjo Agbadan, Soundarzo Tasnim, John Flake

    There has been significant progress in the electrochemical reduction of CO 2 since the seminal work of Hori et al. in 1985 demonstrating hydrocarbon production at copper cathodes. The introduction of gas diffusion electrode (GDE) and membrane electrode assembly (MEA) flow cells have demonstrated progress to produce C 2 products (ethylene, ethanol and acetate) at current densities >150 mA cm -2 with Faradaic Efficiencies (FE) >50% at different types of Cu cathodes. Selectivity depends on several pathways and the intermediate binding strength of species like *CO, *CHO, *OCCO, and *OCCOH. Thus, there are opportunities to engineer or optimize product selectivity. The work advanced ethylene production through Cu-P 0.065 electrocatalyst (Cu δ+ = 0.13), achieving 52% FE at 150 mA cm -2 in 0.1 M KHCO 3 , and remarkably improving to 70% FE in weakly acidic conditions (pH 6) while maintaining 64% FE at 250 mA cm −2 . Electrolyte engineering demonstrated that larger alkali cations (Na + to Cs + ) effectively suppress hydrogen evolution from 31% to 4% while promoting C 2 formation (45% to 89% FE). K + concentration optimization (0.1-2M) further enhanced ethylene production, increasing FE from 42% to 65% at 4V while reducing HER from 48% to 20%. Mechanistic studies revealed K + and OH - species accumulation near the electrocatalyst surface promotes C-C coupling through K + and *OCCO intermediate interactions, while phosphorus doping enhances *CO generation and coupling. In terms of ethanol our work demonstrates that Cu-Sn 0.03 electrocatalyst (Cu δ+ = 0.27) can achieve 48% FE at 350 mA cm -2 under alkaline conditions. A breakthrough in product separation was achieved through a dual-layer membrane configuration incorporating CEM and AEM. This system, using 1M KOH (pH 14) inner layer and 1M KOH+H 3 PO 4 (pH 6) anolyte, reached 51.92% FE for ethanol with minimal anode crossover (8 wt% ethanol. Additionally, anion identity studies (PO 4 2- , SO 4 2- , and NO 4 - ) demonstrated consistent C 2 efficiencies (61-65%) at fixed pH. In terms of acetate production, we show Cu 2 Se electrocatalyst (Cu δ+ = 0.47), demonstrating 40% FE for acetate at 350 mA cm -2 . Notably, all electrocatalysts maintained exceptional stability over 250 hours with minimal degradation (0.02% FE loss/hour). These results show structure-function relationships of electrocatalysts in CO 2 reduction and high levels of ethylene, ethanol, and acetate production; however, several critical barriers related to operating (viz. Energy) cost and durability remain. We conclude with a review of the state of the art and the needs for commercialization.

  • Open Access

    Copper-Epoxy Interface Engineering for High-Frequency Chip-to-Chip Interconnects

    by Junghyun Park, Ignace Agbadan, Monsuru Dauda, Mustapha Bello, John Hendershot, Soundarzo Tasnim, Omotolani Oduyebo, Sunggook Park, Anthony Engler, Jaimal Williamson, et al.

    The reliability of high-frequency chip-to-chip (C2C) interconnects requires the durability of Cu interconnects and polymer dielectric interfaces. In this study, we examine the temperature cycling performance of Cu-epoxy interfaces, including methylimidazole and amine functional silane adhesion promoters along with electroplated or electroless metal interlayers such as Ni, NiCo 0.64 P 0.25 , NiW 0.48 P 0.10 , and CoW 0.66 P 0.17 . X-ray photoelectron spectroscopy is used to determine chemical states and compositions. O diffusion is analyzed using energy-dispersive X-ray spectroscopy. The adhesion strength was measured using a peel tester, and sheet resistance was characterized using a four-point probe before and after temperature cycle tests. Insertion losses were measured using a vector network analyzer as a function of temperature cycling. Our results indicate that organic adhesion promoters such as silanes show improvements in the initial adhesion; however, extended temperature cycling results in weakened interfaces associated with Cu oxidation. The CoW 0.66 P 0.17 metallic interlayer is more durable and exhibits a minimal 0.02 dB mm −1 change in insertion losses at 18 GHz after 1500 cycles.


  • Open Access

    Anolyte Buffering and CO Coverage Effects in the Electrochemical Reduction of CO at Cu Electrocatalysts

    by Mustapha Bello, Monsuru Olatunji Dauda, John Hendershot, Nkechi Kingsley, Ignace Agbadan, Junghyun Park, Soundarzo Tasnim, Omotolani Oduyebo, Anthony Christian Engler, Craig Plaisance, et al.

    Electrolytic CO reduction was investigated at copper electrocatalysts in zero-gap membrane electrode assemblies as a function of buffering agents and cofeeding with CO2 or Ar. Results show an acetate Faradaic efficiency (FE) of 90% at 300 mA cm–2 using pure CO feeds and phosphate-buffered anolyte near pH 8. When using CO feeds with more alkaline anolytes, the hydrogen evolution reaction becomes the dominant reduction reaction, independent of the buffer. Product distributions of cofeeding experiments with CO and CO2 show that increasing CO2 cofeeding results in increased selectivity toward ethylene (42% FE) in near-neutral KHCO3 anolytes or ethanol (40% FE) in alkaline KOH anolytes. Evaluation of several commercial anion exchange membranes shows similar selectivity trends, suggesting product selectivity is dominated by the local pH and surface coverage of CO. Based on these results, we propose pH buffering and CO coverage behaviors that facilitate high selectivities to acetate.