Ignace Kodjo Agbadan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ignace Kodjo Agbadan has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
- Monsuru Olatunji Dauda
Louisiana State University
12 shared publications John C Hendershot
Louisiana State University
9 shared publicationsJohn Flake
Louisiana State University
9 shared publications- Junghyun Park
Louisiana State University
8 shared publications - Mustapha Bello
Louisiana State University
8 shared publications Soundarzo Tasnim
Louisiana State University
8 shared publications
Latest Publications
- Open Access
- 11 September 2026
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 173 (17) , 174502
Electrolytic Reduction of CO 2 in a Flowing Electrolyte Interlayer MEA Cell
A Flowing Electrolyte Interlayer (FEI) electrolyzer is demonstrated for CO 2 reduction. The 3-layer cell includes an anion-exchange membrane, a cation-exchange membrane, and a flowing interlayer that serves as a product-collection stream. The new cell was evaluated using copper-based electrocatalysts, including CuSn 0.03 , CuSn 4 , and Cu 2 Se, for the selective production of ethanol and direct recovery of free acid (formic acid or acetic acid). Analyses, including operando ED-XRD and XAS, confirm structural stability of cell components. The FEI electrolyzer retained up to 63% ethanol Faradaic efficiency while enabling direct recovery of liquid products and suppressing anode crossover to below 2%, a more than 40-fold reduction compared with conventional MEA systems. Channel geometry and flow experiments revealed that product removal is limited at relatively low flow velocities and may be diluted at higher velocities. An optimal interlayer channel configuration was shown to deliver up to 9 weight percent ethanol for over 60 h.
- 11 September 2026
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 173 (17) , 174502
Open AccessElectrolytic Reduction of CO 2 in a Flowing Electrolyte Interlayer MEA Cell
A Flowing Electrolyte Interlayer (FEI) electrolyzer is demonstrated for CO 2 reduction. The 3-layer cell includes an anion-exchange membrane, a cation-exchange membrane, and a flowing interlayer that serves as a product-collection stream. The new cell was evaluated using copper-based electrocatalysts, including CuSn 0.03 , CuSn 4 , and Cu 2 Se, for the selective production of ethanol and direct recovery of free acid (formic acid or acetic acid). Analyses, including operando ED-XRD and XAS, confirm structural stability of cell components. The FEI electrolyzer retained up to 63% ethanol Faradaic efficiency while enabling direct recovery of liquid products and suppressing anode crossover to below 2%, a more than 40-fold reduction compared with conventional MEA systems. Channel geometry and flow experiments revealed that product removal is limited at relatively low flow velocities and may be diluted at higher velocities. An optimal interlayer channel configuration was shown to deliver up to 9 weight percent ethanol for over 60 h.
- 7 July 2026
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2026-01 (38) , 1979
Pressure Effect on the Electrochemical Reduction of CO to Acetate in MEA
We investigate Cu and Cu2Se electrocatalysts operating at 500 and 750 mA cm-2 across several electrolytes (0.1 M KHCO3, 1 M KOH, and phosphate buffer at pH 8) and pressures ranging from 1 to 3 atm. In general, alkaline electrolytes and higher pressures enhance acetate Faradaic efficiency (FE) while suppressing ethylene, ethanol, formate, and hydrogen evolution. In the 0.1 M KHCO3 electrolyte at 500 mA cm-2, acetate FE increased from 57% to 66% at Cu electrodes and from 70% to 77% on Cu2Se when pressure increased from 1 to 3 atm. When using phosphate-buffered electrolytes (pH 8), acetate FE improved from 50% to 60% on Cu and from 61% to 70% on Cu2Se. Remarkably, Cu2Se showed an FE of 92% to acetate at 750 mA cm-2 in an alkaline electrolyte (1 M KOH) under 3 atm, compared to 61% at atmospheric pressure, with the remaining products being predominantly ethanol (1% FE) and hydrogen (5% FE). Furthermore, the additional pressure allows lower cell potentials, decreasing from 3.51 V at 1 atm to 3.46 V at 3 atm, while hydrogen FE declined from 5.98% to 5.34% (12% relative reduction).
- 7 July 2026
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2026-01 (38) , 1979
Pressure Effect on the Electrochemical Reduction of CO to Acetate in MEA
We investigate Cu and Cu2Se electrocatalysts operating at 500 and 750 mA cm-2 across several electrolytes (0.1 M KHCO3, 1 M KOH, and phosphate buffer at pH 8) and pressures ranging from 1 to 3 atm. In general, alkaline electrolytes and higher pressures enhance acetate Faradaic efficiency (FE) while suppressing ethylene, ethanol, formate, and hydrogen evolution. In the 0.1 M KHCO3 electrolyte at 500 mA cm-2, acetate FE increased from 57% to 66% at Cu electrodes and from 70% to 77% on Cu2Se when pressure increased from 1 to 3 atm. When using phosphate-buffered electrolytes (pH 8), acetate FE improved from 50% to 60% on Cu and from 61% to 70% on Cu2Se. Remarkably, Cu2Se showed an FE of 92% to acetate at 750 mA cm-2 in an alkaline electrolyte (1 M KOH) under 3 atm, compared to 61% at atmospheric pressure, with the remaining products being predominantly ethanol (1% FE) and hydrogen (5% FE). Furthermore, the additional pressure allows lower cell potentials, decreasing from 3.51 V at 1 atm to 3.46 V at 3 atm, while hydrogen FE declined from 5.98% to 5.34% (12% relative reduction).
- 24 November 2025
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2025-02 (48) , 3424
Molecular Electrocatalyst (Cu-based composite) for the Electrochemical Reduction of CO 2 in Membrane Electrode Assemblies
The electrochemical reduction of CO 2 to ethanol, acetate and formate provides a circular pathway for carbon products, fuels, and food; however, achievingefficient C-C coupling remains a challenge. Molecular electrocatalysts typically generate single-carbon products, while copper catalysts promote C-C coupling but typically produces a broad spectrum of C 1 and C 2+ products. Herein, we report an established cooperative molecule-metal interface by functionalizing copper with porphyrin complexes and cobalt phthalocyanine (CoPh) that reduce CO 2 to CO, enriching the local reaction environment. With the molecular electrocatalysts yielding maximum CO (87% Faradaic efficiencies; FE CO ) at a low cell potential of 2.97 V, a cascade reaction (CO 2 - CO - C 1 or C 2+ ) on Cu-molecule composite electrocatalyst achieves a shift in catalytic behavior, to oxygenates with FE up to 41% for ethanol at a cell potential of 3.47 V, 36% formate at a cell potential of 3.3 V and an overall C 2+ products increment of 59% at a cell potential of 3.47 V and 63% at a cell potential of 3.7 V on Cu with iron (III) tetra-trimethylanilinium porphyrin pentachloride (FeTMAPP) and Cu with iron (III) tetra-(4-sulfonatophenyl) porphyrin Chloride (FeTPP) respectively. Similarly, 32% and 43% FE increment for the oxygenated products were observed on Cu 2 Se-FeTMAPP and Cu 2 Se-CoPh at a cell potential of 3.47 V and 3.54 V respectively with acetate (50% FE at 3.47 V) and formate (52% FE at 3.3 V) as the primary products. The selectivity shift is likely related to changes in the electrode-electrolyte interface. We show the effect of co-feeding CO and demonstrate the role of the molecular electrocatalyst.
- 24 November 2025
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2025-02 (48) , 3424
Molecular Electrocatalyst (Cu-based composite) for the Electrochemical Reduction of CO 2 in Membrane Electrode Assemblies
The electrochemical reduction of CO 2 to ethanol, acetate and formate provides a circular pathway for carbon products, fuels, and food; however, achievingefficient C-C coupling remains a challenge. Molecular electrocatalysts typically generate single-carbon products, while copper catalysts promote C-C coupling but typically produces a broad spectrum of C 1 and C 2+ products. Herein, we report an established cooperative molecule-metal interface by functionalizing copper with porphyrin complexes and cobalt phthalocyanine (CoPh) that reduce CO 2 to CO, enriching the local reaction environment. With the molecular electrocatalysts yielding maximum CO (87% Faradaic efficiencies; FE CO ) at a low cell potential of 2.97 V, a cascade reaction (CO 2 - CO - C 1 or C 2+ ) on Cu-molecule composite electrocatalyst achieves a shift in catalytic behavior, to oxygenates with FE up to 41% for ethanol at a cell potential of 3.47 V, 36% formate at a cell potential of 3.3 V and an overall C 2+ products increment of 59% at a cell potential of 3.47 V and 63% at a cell potential of 3.7 V on Cu with iron (III) tetra-trimethylanilinium porphyrin pentachloride (FeTMAPP) and Cu with iron (III) tetra-(4-sulfonatophenyl) porphyrin Chloride (FeTPP) respectively. Similarly, 32% and 43% FE increment for the oxygenated products were observed on Cu 2 Se-FeTMAPP and Cu 2 Se-CoPh at a cell potential of 3.47 V and 3.54 V respectively with acetate (50% FE at 3.47 V) and formate (52% FE at 3.3 V) as the primary products. The selectivity shift is likely related to changes in the electrode-electrolyte interface. We show the effect of co-feeding CO and demonstrate the role of the molecular electrocatalyst.
- 24 November 2025
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2025-02 (47) , 2401
Tailoring the Local Environment for Electrochemical Reduction of CO₂ to Ethylene
Ethylene, a petrochemical feedstock exceeding 200 million tons annual demand, is traditionally produced through energy-intensive steam cracking that emits 0.85–1.8 tons CO₂ per ton of product. Electrochemical CO₂ reduction offers a greener alternative, though achieving high selectivity of ethylene remains a huge challenge due to the numerous possible reaction pathways. Here, we explore our findings on electrochemical CO₂ reduction using Cu-P electrocatalysts in weakly acidic environments, where pH 6 conditions provide balance between CO₂ activation and hydrogen evolution in our membrane electrode assembly system (Fig. 1A), achieving remarkable Faradaic efficiencies of 72.84% for ethylene at 300 mA cm⁻² and 51.42% at 500 mA cm⁻², alongside 51% single-pass CO₂ conversion efficiency (Fig. 1B). Our pH-dependent studies illustrate a shift in product selectivity from mixed C₂ products under alkaline conditions to predominantly ethylene in weakly acidic environments (Fig. 1C). Importantly, our research reveals product selectivity is controlled by pH and cation identity, with mechanistic investigations showing how pH-dependent CO coverage alters the competition between ethylene and ethanol formation pathways. Cu-P electrocatalysts maintain stability over 400 hours, positioning our work favorably against previous reports (Fig. 1D). These insights provide crucial guidance for developing high-performance electrocatalytic systems for targeted C₂ product formation, advancing sustainable approaches to address global carbon challenges. Figure 1
- 24 November 2025
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2025-02 (47) , 2401
Tailoring the Local Environment for Electrochemical Reduction of CO₂ to Ethylene
Ethylene, a petrochemical feedstock exceeding 200 million tons annual demand, is traditionally produced through energy-intensive steam cracking that emits 0.85–1.8 tons CO₂ per ton of product. Electrochemical CO₂ reduction offers a greener alternative, though achieving high selectivity of ethylene remains a huge challenge due to the numerous possible reaction pathways. Here, we explore our findings on electrochemical CO₂ reduction using Cu-P electrocatalysts in weakly acidic environments, where pH 6 conditions provide balance between CO₂ activation and hydrogen evolution in our membrane electrode assembly system (Fig. 1A), achieving remarkable Faradaic efficiencies of 72.84% for ethylene at 300 mA cm⁻² and 51.42% at 500 mA cm⁻², alongside 51% single-pass CO₂ conversion efficiency (Fig. 1B). Our pH-dependent studies illustrate a shift in product selectivity from mixed C₂ products under alkaline conditions to predominantly ethylene in weakly acidic environments (Fig. 1C). Importantly, our research reveals product selectivity is controlled by pH and cation identity, with mechanistic investigations showing how pH-dependent CO coverage alters the competition between ethylene and ethanol formation pathways. Cu-P electrocatalysts maintain stability over 400 hours, positioning our work favorably against previous reports (Fig. 1D). These insights provide crucial guidance for developing high-performance electrocatalytic systems for targeted C₂ product formation, advancing sustainable approaches to address global carbon challenges. Figure 1
- 24 November 2025
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2025-02 (48) , 3588
Physical and Chemical Durability of Anion Exchange Membranes Used in the Electrochemical Reduction of CO 2
Membrane electrode assemblies (MEA) benefit from high current densities and FEs in the electrocatalytic CO 2 reduction reaction (CO 2 RR). However, membrane durability remains a challenge for industrial use. The aim of this study is to investigate the degradation mechanisms of three anion exchange membranes (AEMs) using 0.1M KHCO₃ electrolyte over a 250-hour CO 2 reduction period at 150 mA cm -2 . Three AEM materials were considered: FAA-3-50 (Fumatech), PiperION (Versogen), and Sustainion X37-50 (Dioxide Materials). Ex-situ investigations were carried out using techniques such as tensile testing, Attenuated Total Reflectance Fourier Transform Infrared Spectroscopy (ATR-FTIR), and Electrochemical Impedance Spectroscopy (EIS) to evaluate chemical, electrical, and mechanical deterioration. Despite the use of the same near-nuetral KHCO 3 electrolytes, ATR-FTIR analysis showed different degradation patterns: nucleophilic substitution in FAA-3-50, Hoffman elimination in PiperION, and hydroxide-induced imidazolium breakage in Sustainion. According to EIS studies, the observed variation in ohmic resistance led to steady increases in cell potential increases from approximately 3.5 to 4.8 V at a current density of 150 mA cm -2 . HCO 3 ⁻ conductivity decreased by approximately 50% in the 250 hours of operation. Significant losses in mechanical integrity were also observed, including Young's modulus losses of 46% (FAA-3-50), 18% (PiperION), and 78% (Sustainion). The most notable increase in deformation at break was observed in Sustainion, which went from 4.8% to 20.46%, indicating a higher susceptibility to mechanical wear under prolonged use. This study shows that alkaline conditions in CO 2 reduction (including high local pH conditions near the cathode) cause AEM degradation, which in turn contributes to increases in cell potentials ranging from about 400 mV to 800 mV within several hundred hours of electrolysis at current densities in the range of 100 to 300 mA cm -2 .
- 24 November 2025
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2025-02 (48) , 3588
Physical and Chemical Durability of Anion Exchange Membranes Used in the Electrochemical Reduction of CO 2
Membrane electrode assemblies (MEA) benefit from high current densities and FEs in the electrocatalytic CO 2 reduction reaction (CO 2 RR). However, membrane durability remains a challenge for industrial use. The aim of this study is to investigate the degradation mechanisms of three anion exchange membranes (AEMs) using 0.1M KHCO₃ electrolyte over a 250-hour CO 2 reduction period at 150 mA cm -2 . Three AEM materials were considered: FAA-3-50 (Fumatech), PiperION (Versogen), and Sustainion X37-50 (Dioxide Materials). Ex-situ investigations were carried out using techniques such as tensile testing, Attenuated Total Reflectance Fourier Transform Infrared Spectroscopy (ATR-FTIR), and Electrochemical Impedance Spectroscopy (EIS) to evaluate chemical, electrical, and mechanical deterioration. Despite the use of the same near-nuetral KHCO 3 electrolytes, ATR-FTIR analysis showed different degradation patterns: nucleophilic substitution in FAA-3-50, Hoffman elimination in PiperION, and hydroxide-induced imidazolium breakage in Sustainion. According to EIS studies, the observed variation in ohmic resistance led to steady increases in cell potential increases from approximately 3.5 to 4.8 V at a current density of 150 mA cm -2 . HCO 3 ⁻ conductivity decreased by approximately 50% in the 250 hours of operation. Significant losses in mechanical integrity were also observed, including Young's modulus losses of 46% (FAA-3-50), 18% (PiperION), and 78% (Sustainion). The most notable increase in deformation at break was observed in Sustainion, which went from 4.8% to 20.46%, indicating a higher susceptibility to mechanical wear under prolonged use. This study shows that alkaline conditions in CO 2 reduction (including high local pH conditions near the cathode) cause AEM degradation, which in turn contributes to increases in cell potentials ranging from about 400 mV to 800 mV within several hundred hours of electrolysis at current densities in the range of 100 to 300 mA cm -2 .
- 24 November 2025
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2025-02 (25) , 1390
(IE&EE Student Achievement Award) Strategies for Sustainable Ethylene, Ethanol, and Acetate via Electrochemical CO₂ Reduction
There has been significant progress in the electrochemical reduction of CO 2 since the seminal work of Hori et al. in 1985 demonstrating hydrocarbon production at copper cathodes. The introduction of gas diffusion electrode (GDE) and membrane electrode assembly (MEA) flow cells have demonstrated progress to produce C 2 products (ethylene, ethanol and acetate) at current densities >150 mA cm -2 with Faradaic Efficiencies (FE) >50% at different types of Cu cathodes. Selectivity depends on several pathways and the intermediate binding strength of species like *CO, *CHO, *OCCO, and *OCCOH. Thus, there are opportunities to engineer or optimize product selectivity. The work advanced ethylene production through Cu-P 0.065 electrocatalyst (Cu δ+ = 0.13), achieving 52% FE at 150 mA cm -2 in 0.1 M KHCO 3 , and remarkably improving to 70% FE in weakly acidic conditions (pH 6) while maintaining 64% FE at 250 mA cm −2 . Electrolyte engineering demonstrated that larger alkali cations (Na + to Cs + ) effectively suppress hydrogen evolution from 31% to 4% while promoting C 2 formation (45% to 89% FE). K + concentration optimization (0.1-2M) further enhanced ethylene production, increasing FE from 42% to 65% at 4V while reducing HER from 48% to 20%. Mechanistic studies revealed K + and OH - species accumulation near the electrocatalyst surface promotes C-C coupling through K + and *OCCO intermediate interactions, while phosphorus doping enhances *CO generation and coupling. In terms of ethanol our work demonstrates that Cu-Sn 0.03 electrocatalyst (Cu δ+ = 0.27) can achieve 48% FE at 350 mA cm -2 under alkaline conditions. A breakthrough in product separation was achieved through a dual-layer membrane configuration incorporating CEM and AEM. This system, using 1M KOH (pH 14) inner layer and 1M KOH+H 3 PO 4 (pH 6) anolyte, reached 51.92% FE for ethanol with minimal anode crossover (8 wt% ethanol. Additionally, anion identity studies (PO 4 2- , SO 4 2- , and NO 4 - ) demonstrated consistent C 2 efficiencies (61-65%) at fixed pH. In terms of acetate production, we show Cu 2 Se electrocatalyst (Cu δ+ = 0.47), demonstrating 40% FE for acetate at 350 mA cm -2 . Notably, all electrocatalysts maintained exceptional stability over 250 hours with minimal degradation (0.02% FE loss/hour). These results show structure-function relationships of electrocatalysts in CO 2 reduction and high levels of ethylene, ethanol, and acetate production; however, several critical barriers related to operating (viz. Energy) cost and durability remain. We conclude with a review of the state of the art and the needs for commercialization.
- 24 November 2025
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2025-02 (25) , 1390
(IE&EE Student Achievement Award) Strategies for Sustainable Ethylene, Ethanol, and Acetate via Electrochemical CO₂ Reduction
There has been significant progress in the electrochemical reduction of CO 2 since the seminal work of Hori et al. in 1985 demonstrating hydrocarbon production at copper cathodes. The introduction of gas diffusion electrode (GDE) and membrane electrode assembly (MEA) flow cells have demonstrated progress to produce C 2 products (ethylene, ethanol and acetate) at current densities >150 mA cm -2 with Faradaic Efficiencies (FE) >50% at different types of Cu cathodes. Selectivity depends on several pathways and the intermediate binding strength of species like *CO, *CHO, *OCCO, and *OCCOH. Thus, there are opportunities to engineer or optimize product selectivity. The work advanced ethylene production through Cu-P 0.065 electrocatalyst (Cu δ+ = 0.13), achieving 52% FE at 150 mA cm -2 in 0.1 M KHCO 3 , and remarkably improving to 70% FE in weakly acidic conditions (pH 6) while maintaining 64% FE at 250 mA cm −2 . Electrolyte engineering demonstrated that larger alkali cations (Na + to Cs + ) effectively suppress hydrogen evolution from 31% to 4% while promoting C 2 formation (45% to 89% FE). K + concentration optimization (0.1-2M) further enhanced ethylene production, increasing FE from 42% to 65% at 4V while reducing HER from 48% to 20%. Mechanistic studies revealed K + and OH - species accumulation near the electrocatalyst surface promotes C-C coupling through K + and *OCCO intermediate interactions, while phosphorus doping enhances *CO generation and coupling. In terms of ethanol our work demonstrates that Cu-Sn 0.03 electrocatalyst (Cu δ+ = 0.27) can achieve 48% FE at 350 mA cm -2 under alkaline conditions. A breakthrough in product separation was achieved through a dual-layer membrane configuration incorporating CEM and AEM. This system, using 1M KOH (pH 14) inner layer and 1M KOH+H 3 PO 4 (pH 6) anolyte, reached 51.92% FE for ethanol with minimal anode crossover (8 wt% ethanol. Additionally, anion identity studies (PO 4 2- , SO 4 2- , and NO 4 - ) demonstrated consistent C 2 efficiencies (61-65%) at fixed pH. In terms of acetate production, we show Cu 2 Se electrocatalyst (Cu δ+ = 0.47), demonstrating 40% FE for acetate at 350 mA cm -2 . Notably, all electrocatalysts maintained exceptional stability over 250 hours with minimal degradation (0.02% FE loss/hour). These results show structure-function relationships of electrocatalysts in CO 2 reduction and high levels of ethylene, ethanol, and acetate production; however, several critical barriers related to operating (viz. Energy) cost and durability remain. We conclude with a review of the state of the art and the needs for commercialization.
- Open Access
- 1 November 2025
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 14 (11) , 111004
Copper-Epoxy Interface Engineering for High-Frequency Chip-to-Chip Interconnects
The reliability of high-frequency chip-to-chip (C2C) interconnects requires the durability of Cu interconnects and polymer dielectric interfaces. In this study, we examine the temperature cycling performance of Cu-epoxy interfaces, including methylimidazole and amine functional silane adhesion promoters along with electroplated or electroless metal interlayers such as Ni, NiCo 0.64 P 0.25 , NiW 0.48 P 0.10 , and CoW 0.66 P 0.17 . X-ray photoelectron spectroscopy is used to determine chemical states and compositions. O diffusion is analyzed using energy-dispersive X-ray spectroscopy. The adhesion strength was measured using a peel tester, and sheet resistance was characterized using a four-point probe before and after temperature cycle tests. Insertion losses were measured using a vector network analyzer as a function of temperature cycling. Our results indicate that organic adhesion promoters such as silanes show improvements in the initial adhesion; however, extended temperature cycling results in weakened interfaces associated with Cu oxidation. The CoW 0.66 P 0.17 metallic interlayer is more durable and exhibits a minimal 0.02 dB mm −1 change in insertion losses at 18 GHz after 1500 cycles.
- 1 November 2025
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 14 (11) , 111004
Open AccessCopper-Epoxy Interface Engineering for High-Frequency Chip-to-Chip Interconnects
The reliability of high-frequency chip-to-chip (C2C) interconnects requires the durability of Cu interconnects and polymer dielectric interfaces. In this study, we examine the temperature cycling performance of Cu-epoxy interfaces, including methylimidazole and amine functional silane adhesion promoters along with electroplated or electroless metal interlayers such as Ni, NiCo 0.64 P 0.25 , NiW 0.48 P 0.10 , and CoW 0.66 P 0.17 . X-ray photoelectron spectroscopy is used to determine chemical states and compositions. O diffusion is analyzed using energy-dispersive X-ray spectroscopy. The adhesion strength was measured using a peel tester, and sheet resistance was characterized using a four-point probe before and after temperature cycle tests. Insertion losses were measured using a vector network analyzer as a function of temperature cycling. Our results indicate that organic adhesion promoters such as silanes show improvements in the initial adhesion; however, extended temperature cycling results in weakened interfaces associated with Cu oxidation. The CoW 0.66 P 0.17 metallic interlayer is more durable and exhibits a minimal 0.02 dB mm −1 change in insertion losses at 18 GHz after 1500 cycles.
- Open Access
- 1 September 2025
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 172 (9) , 094509
Anion Exchange Membrane Transport and Accelerated Lifetime Testing of Membrane Electrode Assembly Cells for the Electrochemical Reduction of CO2-to-C2 Products
Electrocatalytic carbon dioxide (CO2) reduction to C2+ products holds promise for low carbon intensity fuels, chemicals, and food; however, durability challenges, particularly those associated with carbonate salt precipitation, hinder their commercialization. This report considers water (H2O) and ion transport properties of conventional anion exchange membranes (AEMs) in zero-gap membrane electrode assembly (MEA) configurations using Cu electrocatalysts. Transport characterizations include H2O diffusion, permeability, potassium ion (K+) diffusion, and transference numbers using commercial piperidinium-based (Versogen), quaternary ammonium-based (Fumasep), and imidazolium-based (Dioxide Materials) AEMs. Accelerated lifetime testing of CO2 reduction in MEA cells was conducted using galvanostatic stepping at 6 h intervals to define a precipitation-free operating window. A “critical current density” was identified based on cell potential and cathode pressure behaviors during the current density stepping experiments. When operating the MEA cell in a galvanostatic mode at the critical current density values, cathode drying and precipitation were typically observed in under 60 h of continuous electrolysis; however, operating the cell at a fraction (75%) of the critical current extended continuous operation in the range of 500 to 1000 h.
- 1 September 2025
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 172 (9) , 094509
Open AccessAnion Exchange Membrane Transport and Accelerated Lifetime Testing of Membrane Electrode Assembly Cells for the Electrochemical Reduction of CO2-to-C2 Products
Electrocatalytic carbon dioxide (CO2) reduction to C2+ products holds promise for low carbon intensity fuels, chemicals, and food; however, durability challenges, particularly those associated with carbonate salt precipitation, hinder their commercialization. This report considers water (H2O) and ion transport properties of conventional anion exchange membranes (AEMs) in zero-gap membrane electrode assembly (MEA) configurations using Cu electrocatalysts. Transport characterizations include H2O diffusion, permeability, potassium ion (K+) diffusion, and transference numbers using commercial piperidinium-based (Versogen), quaternary ammonium-based (Fumasep), and imidazolium-based (Dioxide Materials) AEMs. Accelerated lifetime testing of CO2 reduction in MEA cells was conducted using galvanostatic stepping at 6 h intervals to define a precipitation-free operating window. A “critical current density” was identified based on cell potential and cathode pressure behaviors during the current density stepping experiments. When operating the MEA cell in a galvanostatic mode at the critical current density values, cathode drying and precipitation were typically observed in under 60 h of continuous electrolysis; however, operating the cell at a fraction (75%) of the critical current extended continuous operation in the range of 500 to 1000 h.
- 11 July 2025
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2025-01 (40) , 2155
Water and Potassium Transport in Anion Exchange Membranes Used for Electrochemical CO2 Reduction
Alkaline CO2 electrolyzers hold promise for sustainable chemicals and fuels; however, durability challenges, particularly carbonate salt precipitation, hinder their widespread adoption. This study investigates the water and ion transport properties of anion exchange membranes (AEMs) in zero-gap membrane electrode assembly (MEA) configurations, moving beyond the traditional water uptake measurements used in previous CO2 electroreduction literature. The water and potassium transport properties of the three widely used commercial AEMs - PiperION (Versogen), FAA-3 (Fumatech), and Sustainion X37-50RT (Dioxide Materials) - were systematically evaluated using metrics such as water diffusion, transport number, permeability, potassium diffusion, and transference number. Chronopotentiometry was used to identify a critical current density beyond which drying or salt precipitation leads to system failures. Operating at current densities 25% lower than the critical current density significantly extends continuous DC operation from approximately 50 hours to at least 500 hours. Water diffusion and permeability were measured in a liquid-gas cell as a function of membrane thickness. Results indicated Sustainion X37-50RT had the highest water diffusion (3.2 x 10-6 cm2 s-1), followed by PiperION (7.9 x 10-7 cm2 s-1) and FAA-3 (2.9 x 10-7 cm2 s-1). This same trend was observed for water permeation and transport number measurements. Potassium diffusion and transference numbers were measured using a liquid-liquid cell with 0.1M NaHCO3, and 0.1M KHCO3 on each side. Sustainion X37-50RT membranes have the highest potassium diffusion coefficient (6.5 x 10-7 cm2 s-1), followed by FAA-3 (6.0 x 10-8 cm2 s-1) and PiperION (4.5 x 10-8 cm2 s-1). Potassium transference numbers were measured across current densities ranging from 0 to 100 mA cm-2 and held the same trend as the potassium diffusion coefficients. Critical current densities followed the same trend as water diffusion with Sustainion X37-50RT having the highest (180 mA cm-2), followed by PiperION (45 mA cm-2) and FAA-3 (30 mA cm-2). This trend indicates water diffusion to the cathode is crucial to preventing carbonate salt precipitation, especially at increasing current densities. These findings provide fundamental insights for advancing industrial-scale CO2 electrolysis.
- 11 July 2025
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2025-01 (40) , 2155
Water and Potassium Transport in Anion Exchange Membranes Used for Electrochemical CO2 Reduction
Alkaline CO2 electrolyzers hold promise for sustainable chemicals and fuels; however, durability challenges, particularly carbonate salt precipitation, hinder their widespread adoption. This study investigates the water and ion transport properties of anion exchange membranes (AEMs) in zero-gap membrane electrode assembly (MEA) configurations, moving beyond the traditional water uptake measurements used in previous CO2 electroreduction literature. The water and potassium transport properties of the three widely used commercial AEMs - PiperION (Versogen), FAA-3 (Fumatech), and Sustainion X37-50RT (Dioxide Materials) - were systematically evaluated using metrics such as water diffusion, transport number, permeability, potassium diffusion, and transference number. Chronopotentiometry was used to identify a critical current density beyond which drying or salt precipitation leads to system failures. Operating at current densities 25% lower than the critical current density significantly extends continuous DC operation from approximately 50 hours to at least 500 hours. Water diffusion and permeability were measured in a liquid-gas cell as a function of membrane thickness. Results indicated Sustainion X37-50RT had the highest water diffusion (3.2 x 10-6 cm2 s-1), followed by PiperION (7.9 x 10-7 cm2 s-1) and FAA-3 (2.9 x 10-7 cm2 s-1). This same trend was observed for water permeation and transport number measurements. Potassium diffusion and transference numbers were measured using a liquid-liquid cell with 0.1M NaHCO3, and 0.1M KHCO3 on each side. Sustainion X37-50RT membranes have the highest potassium diffusion coefficient (6.5 x 10-7 cm2 s-1), followed by FAA-3 (6.0 x 10-8 cm2 s-1) and PiperION (4.5 x 10-8 cm2 s-1). Potassium transference numbers were measured across current densities ranging from 0 to 100 mA cm-2 and held the same trend as the potassium diffusion coefficients. Critical current densities followed the same trend as water diffusion with Sustainion X37-50RT having the highest (180 mA cm-2), followed by PiperION (45 mA cm-2) and FAA-3 (30 mA cm-2). This trend indicates water diffusion to the cathode is crucial to preventing carbonate salt precipitation, especially at increasing current densities. These findings provide fundamental insights for advancing industrial-scale CO2 electrolysis.
- 11 July 2025
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2025-01 (41) , 2179
(Invited) Durability and Selectivity in the Electrochemical Conversion of CO2/CO to C2 Products
There has been significant progress in the electrochemical reduction of CO2 since Hori's 1985 discovery of hydrocarbon products at Cu electrodes. Since then, several advances have led to ethanol, ethylene, and acetate production at relatively high current densities and Faradaic efficiencies. The level of progress towards industrial-scale CO2 electroreduction within the last decade has been extraordinary; however, several barriers to commercialization remain. Foremost among these are the limited availability and relatively high cost of electricity from renewables or nuclear sources. Relative to the chlor-alkali process, which produces over 80 million metric tons per year via brine electrolysis, the specific energy requirements for C2 products are much higher. For example, ethylene and ethanol require approximately 30 kWh kg−1 and acetic acid or acetate requires approximately 15 kWh kg−1. Even with optimistic predictions of future solar and wind energy costs near $0.03 per kWh, the electrical demand alone results in specific cost that are 2 to 3 times the cost of conventional methods. Further, other requirements such as separation energy and capital costs, can result in added expenses that are on par with the cost of electrolysis alone. In terms of selectivity and carbon efficiency, several works have made progress in terms of the reaction mechanisms and transport of reactants and products. In this regard, we have proposed several reaction mechanisms for ethanol and ethylene that progress through a ketene to acetyl species and a related path for acetate. Our research on reaction mechanisms reveals that Cu active site electronic properties play a role in product selectivity. Cu-P0.065 (Cuδ+ = 0.13) was shown to provide 70% Faradaic efficiency for ethylene in weakly acidic conditions, Cu-Sn0.03 (Cuδ+ = 0.27) electrocatalysts produce 48% FE to ethanol at 350 mA cm−2 in alkaline conditions, and Cu2Se (Cuδ+ = 0.47) can provide over to 40% FE to acetate. Feed composition and pH strongly influence products: pure CO feeds favor acetate (60% FE), while CO2 co-feeding enhances ethylene selectivity to 42% FE. These electrocatalysts maintain stability over 250 hours with minimal degradation; however, several selectivity and efficiency challenges remain. Our research has revealed that water management and salt precipitation remain as key challenges in CO2 reduction via zero-gap membrane electrode assemblies (MEAs), with performance limited by membrane-specific critical current densities. Previous work showed that CO2 electroreduction to C2 products requires water from the anode, and each bicarbonate/carbonate ion co-transports 6-10 water molecules via electroosmotic drag, establishing membrane stability limits based on water transport. Critical current densities for stable operation were estimated near 180 mA·cm⁻² for Sustainion X37-50RT, 45 mA·cm⁻² for PiperION 60, and 30 mA·cm⁻² for Fumasep FAA-3-50. Operating below these thresholds enables remarkable stability - demonstrated by a 1,000-hour continuous operation at a current density of 135 mA·cm⁻². Durability challenges also extend to both electrocatalysts and membranes. Our studies showed copper-based electrocatalysts experience a 19% reduction in electrochemical surface area increasing overpotential by over 400 mV at 150 mA·cm⁻². Anion exchange membranes face hydroxide attack: Sustainion® X37-50 experiences imidazolium cleavage, PiperION undergoes Hoffman elimination, and FAA-3-50 shows nucleophilic substitution. These result in decreased conductivity and significant mechanical integrity losses. The loss of ionic conductivity and mechanical integrity is evidenced by increasing cell potentials and physical membrane failures. In terms of techno-economics, product separation adds significant challenges. PSA-based separations for ethylene struggle with light ends (hydrogen and carbon monoxide) are particularly problematic at low pressures. This adds substantial cost to ethylene separation and impacts ethanol and acetic acid economics. Likewise, ethanol separation from water requires significant energy at low concentrations, with another challenge being ethanol oxidation at the anode. Further, acetate production can be costly because it requires equimolar base consumption and there are challenges in separating acetic acid or acetate from the electrolyte and other MEA products. These are primarily engineering challenges and there are several potential solutions that could enable commercializing CO2 reduction to C2 products.
- 11 July 2025
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2025-01 (41) , 2179
(Invited) Durability and Selectivity in the Electrochemical Conversion of CO2/CO to C2 Products
There has been significant progress in the electrochemical reduction of CO2 since Hori's 1985 discovery of hydrocarbon products at Cu electrodes. Since then, several advances have led to ethanol, ethylene, and acetate production at relatively high current densities and Faradaic efficiencies. The level of progress towards industrial-scale CO2 electroreduction within the last decade has been extraordinary; however, several barriers to commercialization remain. Foremost among these are the limited availability and relatively high cost of electricity from renewables or nuclear sources. Relative to the chlor-alkali process, which produces over 80 million metric tons per year via brine electrolysis, the specific energy requirements for C2 products are much higher. For example, ethylene and ethanol require approximately 30 kWh kg−1 and acetic acid or acetate requires approximately 15 kWh kg−1. Even with optimistic predictions of future solar and wind energy costs near $0.03 per kWh, the electrical demand alone results in specific cost that are 2 to 3 times the cost of conventional methods. Further, other requirements such as separation energy and capital costs, can result in added expenses that are on par with the cost of electrolysis alone. In terms of selectivity and carbon efficiency, several works have made progress in terms of the reaction mechanisms and transport of reactants and products. In this regard, we have proposed several reaction mechanisms for ethanol and ethylene that progress through a ketene to acetyl species and a related path for acetate. Our research on reaction mechanisms reveals that Cu active site electronic properties play a role in product selectivity. Cu-P0.065 (Cuδ+ = 0.13) was shown to provide 70% Faradaic efficiency for ethylene in weakly acidic conditions, Cu-Sn0.03 (Cuδ+ = 0.27) electrocatalysts produce 48% FE to ethanol at 350 mA cm−2 in alkaline conditions, and Cu2Se (Cuδ+ = 0.47) can provide over to 40% FE to acetate. Feed composition and pH strongly influence products: pure CO feeds favor acetate (60% FE), while CO2 co-feeding enhances ethylene selectivity to 42% FE. These electrocatalysts maintain stability over 250 hours with minimal degradation; however, several selectivity and efficiency challenges remain. Our research has revealed that water management and salt precipitation remain as key challenges in CO2 reduction via zero-gap membrane electrode assemblies (MEAs), with performance limited by membrane-specific critical current densities. Previous work showed that CO2 electroreduction to C2 products requires water from the anode, and each bicarbonate/carbonate ion co-transports 6-10 water molecules via electroosmotic drag, establishing membrane stability limits based on water transport. Critical current densities for stable operation were estimated near 180 mA·cm⁻² for Sustainion X37-50RT, 45 mA·cm⁻² for PiperION 60, and 30 mA·cm⁻² for Fumasep FAA-3-50. Operating below these thresholds enables remarkable stability - demonstrated by a 1,000-hour continuous operation at a current density of 135 mA·cm⁻². Durability challenges also extend to both electrocatalysts and membranes. Our studies showed copper-based electrocatalysts experience a 19% reduction in electrochemical surface area increasing overpotential by over 400 mV at 150 mA·cm⁻². Anion exchange membranes face hydroxide attack: Sustainion® X37-50 experiences imidazolium cleavage, PiperION undergoes Hoffman elimination, and FAA-3-50 shows nucleophilic substitution. These result in decreased conductivity and significant mechanical integrity losses. The loss of ionic conductivity and mechanical integrity is evidenced by increasing cell potentials and physical membrane failures. In terms of techno-economics, product separation adds significant challenges. PSA-based separations for ethylene struggle with light ends (hydrogen and carbon monoxide) are particularly problematic at low pressures. This adds substantial cost to ethylene separation and impacts ethanol and acetic acid economics. Likewise, ethanol separation from water requires significant energy at low concentrations, with another challenge being ethanol oxidation at the anode. Further, acetate production can be costly because it requires equimolar base consumption and there are challenges in separating acetic acid or acetate from the electrolyte and other MEA products. These are primarily engineering challenges and there are several potential solutions that could enable commercializing CO2 reduction to C2 products.