QYQing Yan

Qing Yan

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Qing Yan has a total of 42 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Modeling, evaluation, and suppression of crosstalk-induced interfering voltage in quench detection signal cables for fusion device

    by Xinxin Zhu, Yezheng Xiao, Yanlan Hu, Qing Yan, Yu Chen, Biao Shen

    Quench detection (QD) is critical for the operational safety of superconducting magnets in controlled fusion devices. As the operating current in fusion device scale up, intense electromagnetic interference poses a significant challenge to the reliability of QD system (QDS). During plasma discharge and quench current discharge phases, the rapid current variations induce high-voltage (HV) transients with steep gradients ( d u / d t ) on the central solenoid and poloidal field magnets. These transients propagate through long-distance QD cables, triggering capacitive crosstalk that distorts the millivolt-level quench resistive signal. Such interference leads to a degradation of the signal-to-noise ratio, potentially affecting the reliability of QDS. This study presents a systematic approach to evaluating and mitigating crosstalk in HV QD cables. First, the transient characteristics of QD signals are analyzed under extreme fusion environments. A lumped-parameter equivalent circuit model is developed to analytically derive the crosstalk coupling mechanism. To ensure modeling accuracy, the finite element method (FEM) is employed to extract the parasitic capacitance matrix of the multi-conductor cable geometry. Subsequently, a co-simulation platform integrating the FEM-derived parameters into a Simulink circuit model is established to quantitatively evaluate the crosstalk voltage. Finally, impedance balancing and active shielding are evaluated as design measures for reducing the common-mode-to-differential-mode conversion caused by capacitance and impedance asymmetry. The results quantify the reduction in crosstalk-induced error voltage and provide guidance for the electromagnetic compatibility design of QD signal cables in future fusion device.

  • Open Access

    Early quench warning and thermal profiling of 16 kA HTS current lead based on hybrid fiber optic sensing technology

    by Jincheng Jiang, Qicai Ni, Yanlan Hu, Yujun Dong, Yi Shi, Xiang Liu, Yu Chen, Xianzhou Zhao, Qing Yan, Xinxin Zhu, et al.

    To address the challenges of slow quench propagation in high-current high-temperature superconducting (HTS) components for fusion reactors and the susceptibility of conventional voltage detection to electromagnetic interference, this paper proposes a hybrid fiber optic sensing scheme based on Fiber Bragg Gratings (FBG) and Distributed Fiber Optic Sensing (DFOS). Utilizing the CRAFT 16 kA HTS current lead platform, simulated Loss of Flow Accident (LOFA) experiments and 3D electro-thermal coupled numerical simulations were conducted. Results demonstrate a dual-stage protection capability. For LOFA early warning, the FBG system identified thermal anomalies at 168.8 s (equal signal-to-noise ratio (SNR) criterion), leading the conventional voltage trigger (1354.3 s) by nearly 20 minutes. For quench-onset detection via a 3σ deviation threshold, continuous DFOS and discrete FBG captured hotspots at 1337.6 s and 1346.2 s, achieving response leads of 16.7 s and 8.1 s, respectively. This detection scheme provides an expanded safety margin that satisfies the thermal stability requirements for fusion-grade HTS components. By leveraging the continuous spatial sampling of DFOS and the hybrid sensing scheme, this study quantified the azimuthal thermal inhomogeneity within the HTS stacks. Performance data show that FBG yields an SNR of 898 and supports rapid response, making it suitable for millisecond-level protection triggering. Conversely, the continuous DFOS detected the quench onset 8.6 s earlier than the discrete FBG array, quantifying the coupled thermal lag induced by axial undersampling and stochastic azimuthal hotspots. This research confirms that a hybrid sensing strategy, integrating the rapid response of FBGs with the full-field diagnostics of DFOS, provides a measurement strategy for monitoring the operation of future large-scale fusion reactor magnets.

  • Quench Detection and Verification for the CFETR Central Solenoid Model Coil

    by Xianzhou Zhao, Yu Chen, Longgui Zheng, Xinxin Zhu, Yezheng Xiao, Qing Yan, Jincheng Jiang, Yanlan Hu

    Superconducting magnet quench represents one of the most critical risks constraining the safe operation of fusion devices. Once a quench occurs, the electromagnetic energy stored in the magnet is rapidly converted into heat; if the event is not detected promptly and accurately to trigger protection, irreversible coil damage or even catastrophic structural failure may result. In this work, systematic verification of quench detection and protection technologies is carried out on the AC loss and thermal load experimental platform of the CFETR central solenoid model coil (CSMC). A novel scheme integrating multi-redundant primary compensation based on co-wound wire (CWW) and co-wound tape (CWT) with a digital secondary cancellation method (SCM) is proposed, which effectively suppresses inductive noise arising from self-inductance, mutual inductance, and background field variations, enabling stable extraction of 1 mV-level quench signals with noise suppressed within 10 mV. Under a wide range of current ramp rates (80–500 A/s) and complex operating conditions (AC loss and thermal load), the quench detection system reliably discriminates genuine quench events with high detection reliability and triggers interlock protection within 2 s, thereby demonstrating both the superior applicability and engineering feasibility of the proposed approach for high-energy superconducting magnets. This study provides key technical support and experimental basis for the engineering design of quench protection systems for full-scale central solenoid magnets in CFETR.

  • Experimental Study on Quench Detection of Fiber-optic Sensors for High-temperature Superconducting Model Conductors of China’s Next-generation Fusion Magnets

    by Jincheng Jiang, Qing Yan, Yanlan Hu, Qicai Ni, Fang Liu, Huan Jin, HongJun Ma, Guanyu Xiao, Gabriele Colombo, Shuqing Zhang, et al.

    High-temperature superconducting (HTS) magnets are core components of China’s next-generation fusion devices. However, the slow normal zone propagation velocity (NZPV) and the complex electromagnetic environment pose severe challenges to traditional voltage-based quench detection methods. This paper systematically investigates the application of distributed fiber-optic sensing (DFOS) based on optical frequency domain reflectometry (OFDR) technology in the quench detection of HTS model conductors. A model conductor incorporating REBCO CORC cables was designed and developed, and a specialized “loose-tube” stainless steel capillary encapsulation process was employed to integrate the fiber-optic sensors. Experimental results demonstrate that this encapsulation scheme exhibits exceptionally high reliability, maintaining stable signal intensity and a high signal-to-noise ratio (SNR) during the cooling process from 293 K to 4.2 K. In various quench induction tests, the DFOS system showed excellent early warning capabilities: under the equivalent SNR criterion, its detection time was 0.3 s to 2.2 s ahead of traditional voltage taps. Additionally, a significant baseline drift phenomenon was observed in repeatability experiments. Quantitative evaluation using the cooling time constant (τ) revealed a notable thermal lag of the fiber compared to the conductor, with a maximum recovery ratio (τ_fiber/τ_cond) reaching 7.37, which is primarily attributed to the thermal inertia of the helium layer inside the encapsulation. Based on these findings, engineering mitigation strategies are proposed, including the introduction of baseline recovery discrimination logic and the specification of mandatory reset times (e.g., > 19 min). This study provides critical performance benchmarks and technical guidance for the deployment of full-scale distributed fiber-optic systems in high-field HTS magnets.

  • Fault Identification Method for Quench Detection Lines of CSMC and EAST Based on Broadband Impedance Technology

    by Xianzhou Zhao, Yanlan Hu, Jincheng Jiang, Yu Chen, Qing Yan, Xinxin Zhu, Longgui Zheng, Yezheng Xiao, Liangbing Hu

    The China Fusion Engineering Test Reactor Central Solenoid Model Coil (CSMC) project, which commenced construction in 2014, is currently in the experimental phase. Experimental advanced superconducting tokamak (EAST) is a superconducting tokamak nuclear fusion experimental device located in China, dedicated to researching the controllable technology of nuclear fusion and currently in continuous operation. The quench protection system serves as the primary safeguard for the operation of the magnets and plays a critical role in ensuring the success of operational experiments. A key component of this system is the voltage acquisition detection lines, which continuously monitor the magnet’s operational status. The safe and reliable operation of these detection lines is essential for the precise functioning of the system. However, the high-voltage detection lines are subjected to harsh environmental conditions, including nuclear radiation, high voltages, ultra-low temperatures, and other extreme factors. Over time, these cables are prone to electrical failures, such as disconnections, short circuits, and insulation damage. This article applies broadband impedance testing [frequency domain reflectometry (FDR)], a mature nondestructive testing technology, to accurately and rapidly detect and locate various electrical faults in the quench detection lines of CSMC and EAST. Real-world field test results for CSMC and EAST verify that FDR can achieve high-precision fault location for twisted-pair and four-core cables, and effectively distinguish typical faults, such as short circuits, open circuits, and water ingress. The application of FDR provides a reliable technical means for the maintenance and safe operation of quench detection systems in superconducting magnet devices, and can prevent latent defects from evolving into permanent faults.


  • Open Access

    Distributed fiber optic sensing (DFOS) for strain and post-quench diagnosis in the CSMC magnet: Validation and cryogenic challenges

    by Jincheng Jiang, Qicai Ni, Yanlan Hu, Yezheng Xiao, Yu Chen, Xianzhou Zhao, Xinxin Zhu, Qing Yan

    Reliable electromechanical and thermal monitoring is essential for the safe operation of high-field superconducting magnets such as the central solenoid (CS) of the China Fusion Engineering Test Reactor (CFETR). To validate key CS technologies, a Central Solenoid Model Coil (CSMC) was developed as a pre-research platform. Conventional diagnostics, including voltage taps and thermocouples, provide only discrete measurements and cannot offer distributed, high-resolution, multiphysics characterization under cryogenic and high-field conditions. In this work, a distributed fiber optic sensing (DFOS) system based on Rayleigh optical frequency-domain reflectometry (OFDR) was implemented and tested on the CSMC. Stainless-steel-encapsulated single-mode fibers were installed on the inner Nb₃Sn coil and helium outlet tubes to monitor distributed strain and temperature during 20/30 kA electromagnetic cycling, quench events, and warm-up tests. The DFOS accurately captured the linear dependence of spectral offset on the square of current (Δλ ∝ I²) with a coefficient of variation below 5%, revealing nonuniform Lorentz-force-induced stress distribution. Due to the system's limitations in Hz-level temporal resolution and external fiber placement, it was unable to capture local anomalies characteristic of the pre-quench phase. However, the system clearly recorded abrupt strain drops synchronized with the activation of the quench protection system during current discharge. During the warm-up phase, fiber signals reproduced temperature evolution from 4.2 to 200 K and visualized local thermal inhomogeneities in modules P14 and P15, demonstrating potential for hotspot detection. These results confirm the feasibility of DFOS for distributed electromechanical and thermal monitoring in the CSMC, validating its robust capability for post-quench diagnosis and health monitoring, while highlighting the necessary upgrades for future early warning functionality.


  • Open Access

    Design and experimental verification of the quench detection system for the CFETR central solenoid model coil

    by Qing Yan, Yezheng Xiao, Longgui Zheng, Chao Pan, Qicai Ni, Teng Wang, Shuqing Zhang, Yu Chen, Xianzhou Zhao, Liang Guo, et al.


  • Research on Crosstalk of High-Voltage Signal Transmission Cables for Quench Detection System of Chinese Next-Generation Fusion Device

    by Xinxin Zhu, Yezheng Xiao, Yanlan Hu, Longgui Zheng, Qin Yan, Teng Wang, Qicai Ni

    The quench detection system for next-generation fusion device of China face enormous challenges, as their magnet systems are characterized by significantly higher stored energy and faster discharge rates than those in predecessors like EAST and KSTAR. During both the plasma discharge phase and the superconducting magnet quench current discharge phase, rapid current changes induce high and dynamically varying voltages on magnets, particularly in the Central Solenoid (CS) and Poloidal Field (PF) coils, where kilovolt-level inductive voltages can arise. These high-voltage signals can appear on the quench detection signal cables connected to the magnets, leading to capacitive coupling crosstalk between these cables within the same cable tray. Such crosstalk severely interferes with the quench detection signals, compromising the accurate identification of magnet quenches. This can potentially lead to either false quench detection or a failure in quench detection. To address this, the paper presents a systematic investigation into the crosstalk phenomenon. It begins by characterizing the properties of quench detection signals. Subsequently, an electrical circuit model for signal cable crosstalk is established, and the influencing factors of crosstalk are analyzed. Finally, the model is validated through a dedicated experiment, whose results are used to predict crosstalk levels in the operational environment and to propose effective mitigation strategies to ensure robust quench detection.


  • Simulation of Quench Behavior in CS LTS Magnets for Next-Generation Fusion Devices With Time-Varying Operation

    by Yu Chen, Yanlan Hu, Yezheng Xiao, Qing Yan, Longgui Zheng, Xinxin Zhu, Qicai Ni

    In the next generation of fusion devices, the central solenoid (CS) coil needs to withstand large alternating currents and rapidly changing magnetic fields to achieve plasma breakdown, configuration formation and control. In this study, the quench behavior of a representative submodule (CS1U-LTS) is investigated under time-varying current and magnetic field conditions, where the local field ramp rate reaches approximately 2.5 T/s. This alternating operation mode significantly affects the stability of superconducting magnets. However, the current simulation of superconducting magnet quench is mostly based on steady-state current and steady-state background field, which is difficult to reflect the quench propagation characteristics of superconductors under alternating conditions as the current and magnetic field intensity and direction change. To ensure the safe operation of the CS coils under alternating conditions, this paper first analyzes the quench behavior in a reference case with constant peak current prior to an exponential discharge and determines the protection thresholds required to limit the hot spot temperature to below 150 K: 200 mV voltage threshold and 0.5 s time threshold. The quench response at the positive and negative current peaks during time-varying operation is further analyzed. The results show that under the same protection conditions, the maximum temperature of the CS1U-LTS coil in alternating operation still meets the design requirements. In addition, this paper compares the differences in quench propagation near the two peak points, revealing the impact of alternating operation on quench propagation behavior.


  • Induced Voltage Noise Compensation Method Based on CWW + CNN-BiLSTM-Attention

    by Qing Yan, Yezheng Xiao, Qicai Ni, Longgui Zheng, Teng Wang, Xinxin Zhu, Yu Chen, Yanlan Hu

    Induced voltage noise is a significant source of interference in voltage detection, seriously affecting measurement accuracy and system stability. In the complex electromagnetic environment of the Tokamak system, induced voltage noise can exceed 500 V, posing a great challenge to noise suppression in voltage detection signals. This paper presents a two-stage noise compensation approach designed to address the problem. The first stage utilizes a hardware-based Co-wound Wire (CWW) primary compensation method, effectively reducing the induced voltage noise from over 500 V to below 10 V. Building on this foundation, the second stage introduces a deep learning model based on CNN-BiLSTM-Attention as the secondary compensation module, which further reduce the residual noise to below 100 mV over a 1-second window. The proposed method was validated through real-time deployment on the Experimental Advanced Superconducting Tokamak (EAST). Experimental results demonstrate that the method not only achieves excellent compensation effect but also preserves the integrity of critical voltage detection signals throughout operation.