Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Guoshuai Li has a total of 11 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Multi-Objective Optimization Design of the External Rotor Permanent Magnet-Assisted Synchronous Reluctance Motor Based on the Composite Algorithm

    by Guoshuai Li, Huiqin Sun, Weiguang Hu, Ying Li, Yongqiang Bai, Yingjun Guo

    Based on the complex structural characteristics of permanent magnet-assisted synchronous reluctance motors (PMA-SynRMs), this paper proposes a multi-objective optimization design method for the motor using a composite algorithm. Firstly, the power density, electromagnetic torque, cogging torque, and torque fluctuation coefficient were used as optimization targets based on parametric analysis data of 14 motor structure variables, where parametric sensitivity analysis helped select eight optimization variables. Secondly, the motor prediction model was fitted using the genetic algorithm–back propagation (GA-BP) neural network. Finally, non-dominated sorting genetic algorithm-III (NSGA-III), based on the reference points, was used to find the optimization of the prediction model and complete the multi-objective optimization design of the external rotor PMA-SynRM with eight inputs and four outputs. A comparative analysis of the electromagnetic performance of the motor before and after optimization verifies the feasibility of optimizing the motor using the composite algorithm. This paper provides an analytical tool for the multi-parameter and multi-objective PMA-SynRM optimization design.


  • Open Access

    Multi-Parameter Optimization of Stator Coreless Disc Motor Based on Orthogonal Response Surface Method

    by Huiqin Sun, Ying Li, Lucheng Zhang, Zezhao Xue, Weiguang Hu, Guoshuai Li, Yingjun Guo

    In response to the structural optimization problem of PCB stator coreless disc motors, the orthogonal response surface method was used to optimize the motor structure, preliminarily determine the basic parameters of the motor, and conduct orthogonal experiments on the motor parameters based on the optimization design objectives. The optimization factors were the quantity of the magnetic pole of the motor rotor p, the ratio of the main/auxiliary pole sizes Rnd, the thickness Tm of the permanent magnet, and the air gap length δ. The motor torque Td, the amplitude of the magnetic density of the air gap Bδ, and the waveform distortion rate THD were used as optimization objectives. The motor parameters that cause the motor torque to reach a maximum cause the air gap magnetic density to reach a maximum and the waveform distortion rate to reach a minimum. Due to the use of PCB plates instead of motor stator cores in the PCB coreless disc motors, the service life of the PCB board during motor operation will be reduced with the temperature increase generated by the stator winding. To solve this problem, a response surface analysis of the motor was carried out to reduce the increase in the temperature of the stator windings during the operation of the motor. The PCB board and stator winding are the main factors affecting the motor’s temperature increase. Taking the thickness of the PCB board, the hole diameter on the board, and the uneven width of the stator winding as optimization factors, the motor parameters with the lowest increase in the temperature of the motor winding were obtained. A simulation analysis was conducted using Ansys/Maxwell software, and the results prove the feasibility of the optimization.


  • Open Access

    Image Processing Techniques for Shock Wave Detection and Tracking in High Speed Schlieren and Shadowgraph Systems

    by Guoshuai Li, Muhammed Burak Agir, Konstantinos Kontis, Takahiro Ukai, Sriram Rengarajan

    Schlieren and shadowgraph photography has been widely used to offer insight into the flow field in aerospace engineering due to their ease of application. The high-speed schlieren and shadowgraph techniques are typically applied to investigation of unsteady shock wave structure including shock reflection patterns and shock wave/boundary layer interactions, etc. Generally, qualitative analysis is performed based on the schlieren and shadowgraph image sequences. To process and analyze the large data set of the high-speed schlieren and shadowgraph images quantitatively, especially for the shock wave detection and tracking, a software was developed based on MATLAB GUI and its image processing toolbox. In this study, the image processing techniques exploited in the software, such as background subtraction, filter, threshold, edge detection, and shock tracking are presented. A case study on the phenomena of shock wave reflection from a solid surface was conducted. The results show that the proper filter method and the background image subtraction can effectively eliminate the image noises in frequency domain, which makes it easier to analyze the flow structure. Moreover, the instantaneous locations of shock waves are detected accurately, and the shock wave propagation speed calculated using the developed software are consistent with those of previous studies.