Shuangxi Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Shuangxi Li has a total of 52 co-authors. Here are the top co-authors by number of shared publications:
- Jun Zhao
School of Mechanical Engineering, Beijing Institute of Technology, Beijing 100081, China
4 shared publications - Dengyu Liu
College of Mechanical and Electrical Engineering, Beijing University of Chemical Technology, Beijing 100029, China
3 shared publications Enzhe Bi
Beijing Univ Chem Technol, Beijing 100029, Peoples R China
2 shared publications- Lele Huang
College of Mechanical and Electrical Engineering, Beijing University of Chemical Technology, Beijing 100029, China
2 shared publications - Runmei Ma
College of Mechanical and Electrical Engineering, Beijing University of Chemical Technology, Beijing 100029, China
2 shared publications Xinghua Liu
China State Shipbuilding Co., Ltd
2 shared publications
Latest Publications
- 3 August 2026
- Published by Taylor & Francis in Tribology Transactions
- Vol. 69 (6) , 1253-1270
Analysis of Dynamic Characteristics of Mixed Lubrication Mechanical Seals Under Impact Conditions Considering Three Dimensional Fractal Contact
Fluid machinery is extensively applied in process industries such as petrochemicals, aerospace, and nuclear power generation. Its safe operation relies heavily on the reliability of mechanical seal...
- 3 August 2026
- Published by Taylor & Francis in Tribology Transactions
- Vol. 69 (6) , 1253-1270
Analysis of Dynamic Characteristics of Mixed Lubrication Mechanical Seals Under Impact Conditions Considering Three Dimensional Fractal Contact
Fluid machinery is extensively applied in process industries such as petrochemicals, aerospace, and nuclear power generation. Its safe operation relies heavily on the reliability of mechanical seal...
- Open Access
- 1 January 2026
- Published by Chinese Journal of Mechanical Engineering in Journal of Mechanical Engineering
- Vol. 62 (9) , 281-290
High-temperature and High-speed Air Film Floating Ring Seal Constant Clearance Design and Leakage Analysis
- 1 January 2026
- Published by Chinese Journal of Mechanical Engineering in Journal of Mechanical Engineering
- Vol. 62 (9) , 281-290
Open AccessHigh-temperature and High-speed Air Film Floating Ring Seal Constant Clearance Design and Leakage Analysis
- Open Access
Dynamic Performance Analysis of Gas Film Floating Ring Seals Based on the Reynolds–Bernoulli Small-Perturbation Model
Gas film floating ring seals are extensively utilized in aircraft engines, and precise analysis of gas film performance is crucial for ensuring reliable seal design. For this reason, this paper proposes the Reynolds–Bernoulli small-perturbation (RBSP) model to analyze the performance of the gas film based on the conservation of mechanical energy. Through experimental verification and comparison with other analytical models, the results of the RBSP model calculations are both reliable and more broadly applicable. Analyses using the finite element method revealed that the differential pressure effect of Poiseuille flow and the dynamic pressure effect of Couette flow are the primary factors enabling the floating ring to overcome resistance and establish a non-contact seal. Additionally, an appropriate sealing clearance and an increased width of the floating ring could significantly enhance the dynamic performance of the seal. The research findings offer a dependable performance analysis method for designers of gas film floating ring seals.
Open AccessDynamic Performance Analysis of Gas Film Floating Ring Seals Based on the Reynolds–Bernoulli Small-Perturbation Model
Gas film floating ring seals are extensively utilized in aircraft engines, and precise analysis of gas film performance is crucial for ensuring reliable seal design. For this reason, this paper proposes the Reynolds–Bernoulli small-perturbation (RBSP) model to analyze the performance of the gas film based on the conservation of mechanical energy. Through experimental verification and comparison with other analytical models, the results of the RBSP model calculations are both reliable and more broadly applicable. Analyses using the finite element method revealed that the differential pressure effect of Poiseuille flow and the dynamic pressure effect of Couette flow are the primary factors enabling the floating ring to overcome resistance and establish a non-contact seal. Additionally, an appropriate sealing clearance and an increased width of the floating ring could significantly enhance the dynamic performance of the seal. The research findings offer a dependable performance analysis method for designers of gas film floating ring seals.
- Open Access
- 15 August 2024
- Published by MDPI AG in Lubricants
- Vol. 12 (8) , 288
Material Optimization Method for a Spring-Energized Seal Based on Wear Analysis
Spring-energized seals demonstrate good sealing performance over a wide range of pressures and temperatures and can compensate for installation eccentricity, high-temperature aging, etc. However, as a contact seal, its polytetrafluoroethylene (PTFE) jacket material is easily worn during the rotation of the end face, which leads to a decline in sealing performance and, ultimately, seal failure. Based on the Archard wear model, a performance prediction model of the spring-energized seal was established by combining tests and numerical analyses. In order to improve the tribological performance of spring-energized seals made of PTFE, varied fillers were added to modify the PTFE, and the tribological and mechanical properties of PTFE composites with varied fillers were measured in experiments. Using a performance prediction model for spring-energized seals, the variation in the friction performance of seals made of these filled PTFEs during the operating cycle was analyzed. The results showed that the performance prediction model can accurately simulate this variation. After a certain amount of wear, the deviation between the simulated data and the experimental data was within ±5%. Compared with spring-energized seals made of pure PTFE, the friction torque of spring-energized seals made of GF/PTFE was reduced by 28.97% at most, and the friction torque reduction rate was lowered by 22.25%.
- 15 August 2024
- Published by MDPI AG in Lubricants
- Vol. 12 (8) , 288
Open AccessMaterial Optimization Method for a Spring-Energized Seal Based on Wear Analysis
Spring-energized seals demonstrate good sealing performance over a wide range of pressures and temperatures and can compensate for installation eccentricity, high-temperature aging, etc. However, as a contact seal, its polytetrafluoroethylene (PTFE) jacket material is easily worn during the rotation of the end face, which leads to a decline in sealing performance and, ultimately, seal failure. Based on the Archard wear model, a performance prediction model of the spring-energized seal was established by combining tests and numerical analyses. In order to improve the tribological performance of spring-energized seals made of PTFE, varied fillers were added to modify the PTFE, and the tribological and mechanical properties of PTFE composites with varied fillers were measured in experiments. Using a performance prediction model for spring-energized seals, the variation in the friction performance of seals made of these filled PTFEs during the operating cycle was analyzed. The results showed that the performance prediction model can accurately simulate this variation. After a certain amount of wear, the deviation between the simulated data and the experimental data was within ±5%. Compared with spring-energized seals made of pure PTFE, the friction torque of spring-energized seals made of GF/PTFE was reduced by 28.97% at most, and the friction torque reduction rate was lowered by 22.25%.
- Open Access
Study on the Evolution of Sealing Performance during the Start-Up Process of Dynamic Pressure Seals Based on Three-Dimensional Fractal Functions
A model based on a three-dimensional fractal function is developed and used in conjunction with experiments to analyze the evolutionary pattern of sealing performance during the start-up process of dynamic pressure seals, and the influence of end-face microscopic features on the evolution law is discussed. It is found that the opening state of the seal is divided into three stages: the non-opened stage, transition stage, and full-opened stage. The isotropic dimensions of the cavities have a coupling effect on the leakage, and they diminish as the speed increases. In order to enhance the sealing performance during start-up, it is suggested that the seal faces have a fractal dimension of 2.4 to 2.6, and a characteristic factor of less than 1 × 10−9 m.
Open AccessStudy on the Evolution of Sealing Performance during the Start-Up Process of Dynamic Pressure Seals Based on Three-Dimensional Fractal Functions
A model based on a three-dimensional fractal function is developed and used in conjunction with experiments to analyze the evolutionary pattern of sealing performance during the start-up process of dynamic pressure seals, and the influence of end-face microscopic features on the evolution law is discussed. It is found that the opening state of the seal is divided into three stages: the non-opened stage, transition stage, and full-opened stage. The isotropic dimensions of the cavities have a coupling effect on the leakage, and they diminish as the speed increases. In order to enhance the sealing performance during start-up, it is suggested that the seal faces have a fractal dimension of 2.4 to 2.6, and a characteristic factor of less than 1 × 10−9 m.
- Open Access
- 15 February 2024
- Published by Springer Nature in Research Square
Analysis of Wear Characteristics of Hydrodynamic Seals During Start- up Using 3D Fractal Characterization and Study of Opening Performance Degradation Mechanism
To investigate the degradation mechanism of the opening performance of hydrodynamic seals during multiple start-ups, a model was proposed to analyze the wear characteristics during the start-up process, and an experimental study was conducted. It has been discovered that the state evolution of the hydrodynamic seal during the single start-up process occurs in five stages. The main factor that influences the deterioration of the initial performance of hydrodynamic seals during multiple start-ups is the decrease in the depth of the root groove. To prevent the deterioration of the initial performance of the hydrodynamic seal, it is essential to minimize processing errors in groove depth and reduce the residence time during the mid-speed and mid-load stages of the starting process.
- 15 February 2024
- Published by Springer Nature in Research Square
Open AccessAnalysis of Wear Characteristics of Hydrodynamic Seals During Start- up Using 3D Fractal Characterization and Study of Opening Performance Degradation Mechanism
To investigate the degradation mechanism of the opening performance of hydrodynamic seals during multiple start-ups, a model was proposed to analyze the wear characteristics during the start-up process, and an experimental study was conducted. It has been discovered that the state evolution of the hydrodynamic seal during the single start-up process occurs in five stages. The main factor that influences the deterioration of the initial performance of hydrodynamic seals during multiple start-ups is the decrease in the depth of the root groove. To prevent the deterioration of the initial performance of the hydrodynamic seal, it is essential to minimize processing errors in groove depth and reduce the residence time during the mid-speed and mid-load stages of the starting process.
- Open Access
Friction and Wear Characteristics of Cr-CNTs Composite Coating End Faces of High-Temperature Mechanical Seals
To improve the reliability of the end faces of high-temperature mechanical seals, a high-performance composite material that introduces carbon nanotubes (CNTs) into the laser-melted Cr coating is proposed. In this study, for high-temperature and high-speed mechanical seals under actual working conditions, friction and wear tests were conducted under different working conditions and using different end face materials. The high-temperature tribological properties of the Cr-CNTs coatings were analyzed, and the strengthening mechanism of the Cr-CNTs coatings on end faces was investigated. The results indicate that the wear resistance of the Cr-CNTs coating at high temperatures is first enhanced and then weakened with the increase in the CNTs content. The composite coating end face performance is optimal when the CNTs content is 10 wt%. The presence of CNTs between the end faces when grinding against the graphite ring favors the generation of a graphite film. The coefficient of friction of the Cr-CNTs coating is reduced by at least 12.46% compared to the Cr coating at a temperature of 483 K. This study provides reference examples for the application of carbon nanotubes in high-performance mechanical seals and new research ideas for improving the performance of mechanical seal end faces.
Open AccessFriction and Wear Characteristics of Cr-CNTs Composite Coating End Faces of High-Temperature Mechanical Seals
To improve the reliability of the end faces of high-temperature mechanical seals, a high-performance composite material that introduces carbon nanotubes (CNTs) into the laser-melted Cr coating is proposed. In this study, for high-temperature and high-speed mechanical seals under actual working conditions, friction and wear tests were conducted under different working conditions and using different end face materials. The high-temperature tribological properties of the Cr-CNTs coatings were analyzed, and the strengthening mechanism of the Cr-CNTs coatings on end faces was investigated. The results indicate that the wear resistance of the Cr-CNTs coating at high temperatures is first enhanced and then weakened with the increase in the CNTs content. The composite coating end face performance is optimal when the CNTs content is 10 wt%. The presence of CNTs between the end faces when grinding against the graphite ring favors the generation of a graphite film. The coefficient of friction of the Cr-CNTs coating is reduced by at least 12.46% compared to the Cr coating at a temperature of 483 K. This study provides reference examples for the application of carbon nanotubes in high-performance mechanical seals and new research ideas for improving the performance of mechanical seal end faces.
- Open Access
- 25 September 2023
- Published by Springer Nature in Research Square
Prediction Method for Aging Life of Rubber O-Rings Based on GRU-LSTM Neural Network
This paper proposes a prediction model for rubber aging life based on the GRU-LSTM neural network to address the issue of sealing failure caused by material aging of rubber O-rings in the petrochemical industry. The model aims to overcome the limits of existing methods, which have low prediction accuracy and poor stability. In this study, we conducted rubber aging experiments to get data on rubber compression set at different temperatures. After preprocessing the data, we experimentally verified and compared the GRU-LSTM model with the two-layer LSTM model, two-layer GRU model, and BP neural network. Finally, we carried out an example analysis and application of high-temperature flange sealing in a chemical equipment. The results revealed significant differences between the two types of rubber, NBR-26 and HNBR. When using the aging data at 60, 80, and 100°C to predict the aging data at 70 and 90°C, the R2 values for NBR-26 and HNBR were 0.9968 and 0.9945, respectively. These findings highlight the superior predictive performance of the proposed model. These results show significantly better prediction performance compared to the other three models. Further, the accuracy of the prediction results increased with the number of temperature levels and samples. We recommend using at least three temperatures for prediction, and a larger sample size is preferable. The example analysis showed that this prediction model can help decide the replacement cycle of high-temperature flange rubber O-rings at different storage temperatures, reducing maintenance costs.
- 25 September 2023
- Published by Springer Nature in Research Square
Open AccessPrediction Method for Aging Life of Rubber O-Rings Based on GRU-LSTM Neural Network
This paper proposes a prediction model for rubber aging life based on the GRU-LSTM neural network to address the issue of sealing failure caused by material aging of rubber O-rings in the petrochemical industry. The model aims to overcome the limits of existing methods, which have low prediction accuracy and poor stability. In this study, we conducted rubber aging experiments to get data on rubber compression set at different temperatures. After preprocessing the data, we experimentally verified and compared the GRU-LSTM model with the two-layer LSTM model, two-layer GRU model, and BP neural network. Finally, we carried out an example analysis and application of high-temperature flange sealing in a chemical equipment. The results revealed significant differences between the two types of rubber, NBR-26 and HNBR. When using the aging data at 60, 80, and 100°C to predict the aging data at 70 and 90°C, the R2 values for NBR-26 and HNBR were 0.9968 and 0.9945, respectively. These findings highlight the superior predictive performance of the proposed model. These results show significantly better prediction performance compared to the other three models. Further, the accuracy of the prediction results increased with the number of temperature levels and samples. We recommend using at least three temperatures for prediction, and a larger sample size is preferable. The example analysis showed that this prediction model can help decide the replacement cycle of high-temperature flange rubber O-rings at different storage temperatures, reducing maintenance costs.
- Open Access
- 14 May 2023
- Published by MDPI AG in Lubricants
- Vol. 11 (5) , 220
The Tribological Performance of Frictional Pair of Gas–Liquid Miscible Backflow Pumping Seal in Oil–Air Environment
The gas–liquid miscible backflow pumping seal (G-LMBPHS) is a non-contact mechanical seal that is suitable for high-speed bearing chambers. However, the tribological properties and wear mechanisms of the frictional pair of G-LMBPHS in an oil–air environment have not yet been comprehensively studied. In this study, the tribological properties of six frictional pairs, consisting of three hard materials (18Cr2Ni4WA, Al2O3 coating, and Cr2O3 coating) and two soft materials (metal-impregnated graphite [Metal-IG] and resin-impregnated graphite [Resin-IG]), were analyzed using a disc-on-disc tribometer. An oil–air environment was created using a minimal quantity lubrication (MQL) system and a closed chamber. The results show that the COF of the four frictional pairs consisting of two coatings and two graphites decreases gradually with increasing rotational speed, and the frictional pairs composed of Al2O3 coating and Resin-IG and Cr2O3 coating and Resin-IG have the lowest COF between 0.022 and 0.03. Therefore, the frictional pairs of G-LMBPHS are in a mixed lubrication condition. The lubricant in the oil–air environment is adsorbed and stored in pits on the surface of graphite and coatings, enhancing the hydrodynamic effect of the spiral grooves and reducing the COF by up to 45%. Metal-IG has better wear resistance than Resin-IG, and the frictional pair consisting of Cr2O3 coating and Metal-IG has the lightest wear. This study provides an important basis for the selection of G-LMBPHS frictional pairs in oil–air environments.
- 14 May 2023
- Published by MDPI AG in Lubricants
- Vol. 11 (5) , 220
Open AccessThe Tribological Performance of Frictional Pair of Gas–Liquid Miscible Backflow Pumping Seal in Oil–Air Environment
The gas–liquid miscible backflow pumping seal (G-LMBPHS) is a non-contact mechanical seal that is suitable for high-speed bearing chambers. However, the tribological properties and wear mechanisms of the frictional pair of G-LMBPHS in an oil–air environment have not yet been comprehensively studied. In this study, the tribological properties of six frictional pairs, consisting of three hard materials (18Cr2Ni4WA, Al2O3 coating, and Cr2O3 coating) and two soft materials (metal-impregnated graphite [Metal-IG] and resin-impregnated graphite [Resin-IG]), were analyzed using a disc-on-disc tribometer. An oil–air environment was created using a minimal quantity lubrication (MQL) system and a closed chamber. The results show that the COF of the four frictional pairs consisting of two coatings and two graphites decreases gradually with increasing rotational speed, and the frictional pairs composed of Al2O3 coating and Resin-IG and Cr2O3 coating and Resin-IG have the lowest COF between 0.022 and 0.03. Therefore, the frictional pairs of G-LMBPHS are in a mixed lubrication condition. The lubricant in the oil–air environment is adsorbed and stored in pits on the surface of graphite and coatings, enhancing the hydrodynamic effect of the spiral grooves and reducing the COF by up to 45%. Metal-IG has better wear resistance than Resin-IG, and the frictional pair consisting of Cr2O3 coating and Metal-IG has the lightest wear. This study provides an important basis for the selection of G-LMBPHS frictional pairs in oil–air environments.