Basma Ben Difallah
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Basma Ben Difallah has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Mohamed Kharrat
Laboratory of Electromechanical Systems, National School of Engineers of Sfax, University of Sfax, Sfax 3038, Tunisia
8 shared publications - António Bastos Pereira
TEMA—Centre for Mechanical Technology and Automation, Department of Mechanical Engineering, University of Aveiro, Campus de Santiago, 3810-193 Aveiro, Portugal
4 shared publications - Fida Harabi
Laboratory of Electromechanical Systems, National School of Engineers of Sfax, University of Sfax, Sfax 3038, Tunisia
2 shared publications - Filipe Jose Oliveira
Department of Materials and Ceramic Engineering, CICECO—Aveiro Institute of Materials, University of Aveiro, 3810-193 Aveiro, Portugal
2 shared publications - Isabel Duarte
University of Aveiro
2 shared publications - Mabrouka Akrout
Laboratory of Electromechanical Systems, National School of Engineers of Sfax, University of Sfax, Soukra Road, Km 3.5, P.O. Box 1173, Sfax 3038, Tunisia
2 shared publications
Latest Publications
- Open Access
- 26 February 2026
- Published by MDPI AG in Lubricants
- Vol. 14 (3) , 100
On the Microstructural and Tribological Investigations of WC-12Co/NiCrFeSiAlBC HVOF Cermet Coatings: Effects of WC-12Co Fraction
Previous research indicates that WC-12Co contents above 60 wt.% in feedstock powders for cermet coatings impair adhesion and wear resistance. This study characterizes NiCrFeSiAlBC coatings—unreinforced or reinforced with 65 wt.% or 85 wt.% WC-12Co—applied via high-velocity oxy-fuel (HVOF) spraying onto stainless steel substrates under controlled parameters. It quantifies the influence of high carbide volume fractions within the NiCrFeSiAlBC matrix on microstructure and tribomechanical performance. Microstructural analysis revealed uniformly distributed cermet layers featuring dissolved reinforcements and WC hard phase formation, with minimal W2C crystallization. Elevated WC-12Co incorporation promoted densification and reduced porosity. Vickers microhardness tests (HV 0.3) demonstrated increased hardness upon WC-12Co addition, attributable to finer particle sizes, lower porosity, and the presence of WC phases alongside crystallographic refinements. Under dry reciprocating sliding conditions, friction coefficients and wear volumes decreased markedly. Consequently, the coating with 85 wt.% WC exhibited the best mechanical and tribological properties.
- 26 February 2026
- Published by MDPI AG in Lubricants
- Vol. 14 (3) , 100
Open AccessOn the Microstructural and Tribological Investigations of WC-12Co/NiCrFeSiAlBC HVOF Cermet Coatings: Effects of WC-12Co Fraction
Previous research indicates that WC-12Co contents above 60 wt.% in feedstock powders for cermet coatings impair adhesion and wear resistance. This study characterizes NiCrFeSiAlBC coatings—unreinforced or reinforced with 65 wt.% or 85 wt.% WC-12Co—applied via high-velocity oxy-fuel (HVOF) spraying onto stainless steel substrates under controlled parameters. It quantifies the influence of high carbide volume fractions within the NiCrFeSiAlBC matrix on microstructure and tribomechanical performance. Microstructural analysis revealed uniformly distributed cermet layers featuring dissolved reinforcements and WC hard phase formation, with minimal W2C crystallization. Elevated WC-12Co incorporation promoted densification and reduced porosity. Vickers microhardness tests (HV 0.3) demonstrated increased hardness upon WC-12Co addition, attributable to finer particle sizes, lower porosity, and the presence of WC phases alongside crystallographic refinements. Under dry reciprocating sliding conditions, friction coefficients and wear volumes decreased markedly. Consequently, the coating with 85 wt.% WC exhibited the best mechanical and tribological properties.
- Open Access
- 3 July 2025
- Published by MDPI AG in Technologies
- Vol. 13 (7) , 281
Advanced HVOF-Sprayed Carbide Cermet Coatings as Environmentally Friendly Solutions for Tribological Applications: Research Progress and Current Limitations
Thermally sprayed carbide cermet coatings, particularly those based on tungsten carbide (WC) and chromium carbide (Cr3C2) and produced with the high velocity oxygen fuel (HVOF) process, are used in tribological applications as environmentally friendly alternatives to electroplated hard chrome coatings. These functional coatings are especially prevalent in the automotive industry, offering excellent wear resistance. However, their mechanical and tribological performances are highly dependent on factors such as feedstock powders, spray parameters, and service conditions. This review aims to gain deeper insights into the above elements. It also outlines emerging advancements in HVOF technology—including in situ powder mixing, laser treatment, artificial intelligence integration, and the use of novel materials such as rare earth elements or transition metals—which can further enhance coating performance and broaden their applications to sectors such as the aerospace and hydro-machinery industries. Finally, this literature review focuses on process optimization and sustainability, including environmental and health impacts, critical material use, and operational limitations. It uses a life cycle assessment (LCA) as a tool for evaluating ecological performance and addresses current challenges such as exposure risks, process control constraints, and the push toward safer, more sustainable alternatives to traditional WC and Cr3C2 cermet coatings.
- 3 July 2025
- Published by MDPI AG in Technologies
- Vol. 13 (7) , 281
Open AccessAdvanced HVOF-Sprayed Carbide Cermet Coatings as Environmentally Friendly Solutions for Tribological Applications: Research Progress and Current Limitations
Thermally sprayed carbide cermet coatings, particularly those based on tungsten carbide (WC) and chromium carbide (Cr3C2) and produced with the high velocity oxygen fuel (HVOF) process, are used in tribological applications as environmentally friendly alternatives to electroplated hard chrome coatings. These functional coatings are especially prevalent in the automotive industry, offering excellent wear resistance. However, their mechanical and tribological performances are highly dependent on factors such as feedstock powders, spray parameters, and service conditions. This review aims to gain deeper insights into the above elements. It also outlines emerging advancements in HVOF technology—including in situ powder mixing, laser treatment, artificial intelligence integration, and the use of novel materials such as rare earth elements or transition metals—which can further enhance coating performance and broaden their applications to sectors such as the aerospace and hydro-machinery industries. Finally, this literature review focuses on process optimization and sustainability, including environmental and health impacts, critical material use, and operational limitations. It uses a life cycle assessment (LCA) as a tool for evaluating ecological performance and addresses current challenges such as exposure risks, process control constraints, and the push toward safer, more sustainable alternatives to traditional WC and Cr3C2 cermet coatings.
- 13 May 2025
- Published by Springer Nature
- p. 168-178
Challenges in Thermal Spray to Design Engineering Coatings and Associated Environmental Concerns
- 13 May 2025
- Published by Springer Nature
- p. 168-178
Challenges in Thermal Spray to Design Engineering Coatings and Associated Environmental Concerns
- 27 September 2024
- Published by Springer Nature
- p. 245-252
Tribological Study of Polymer-Metal Composite Coatings Deposited onto Organic Substrates
- 27 September 2024
- Published by Springer Nature
- p. 245-252
Tribological Study of Polymer-Metal Composite Coatings Deposited onto Organic Substrates
- Open Access
- 24 September 2024
- Published by MDPI AG in Journal of Composites Science
- Vol. 8 (10) , 382
Elaboration and Experimental Characterizations of Copper-Filled Polyamide Micro-Composites for Tribological Applications
Polyamide 66 (PA66) has been used for dynamic bearing applications due to its good wear and abrasion resistance, hardness, and rigidity. PA66/copper micro-composites were studied with respect to micro-mechanical, tribological, and structural properties. A mixing step followed by injection molding was used to develop the different composites: PA66+5 wt.% Cu, PA66+10 wt.% Cu, and PA66+15 wt.% Cu. The morphological aspects of the composites were studied using scanning electron microscopy and microtomography. Good dispersion and adhesion of Cu particles across the matrix were also seen. DSC analysis showed a slight improvement in the % of crystallinity and thermal characteristics of the composites, particularly with 5 wt.% filler. Additional crystallization enhanced the tensile performance of the composites, including the modulus, elongation at break, and tensile strength. Nanoindentation tests also indicated an increase in indentation hardness and elastic modulus as a function of the filler fraction. A pin-on-disk tribometer was used to study the friction and wear properties of neat PA66 and copper-filled PA66 composites. It was found that the composite with 5 weight percent copper had the best wear resistance. A progressive decrease in the friction coefficient was also seen. Copper filler increases hardness and may effectively reduce the temperature at contact interfaces during rotating cycles.
- 24 September 2024
- Published by MDPI AG in Journal of Composites Science
- Vol. 8 (10) , 382
Open AccessElaboration and Experimental Characterizations of Copper-Filled Polyamide Micro-Composites for Tribological Applications
Polyamide 66 (PA66) has been used for dynamic bearing applications due to its good wear and abrasion resistance, hardness, and rigidity. PA66/copper micro-composites were studied with respect to micro-mechanical, tribological, and structural properties. A mixing step followed by injection molding was used to develop the different composites: PA66+5 wt.% Cu, PA66+10 wt.% Cu, and PA66+15 wt.% Cu. The morphological aspects of the composites were studied using scanning electron microscopy and microtomography. Good dispersion and adhesion of Cu particles across the matrix were also seen. DSC analysis showed a slight improvement in the % of crystallinity and thermal characteristics of the composites, particularly with 5 wt.% filler. Additional crystallization enhanced the tensile performance of the composites, including the modulus, elongation at break, and tensile strength. Nanoindentation tests also indicated an increase in indentation hardness and elastic modulus as a function of the filler fraction. A pin-on-disk tribometer was used to study the friction and wear properties of neat PA66 and copper-filled PA66 composites. It was found that the composite with 5 weight percent copper had the best wear resistance. A progressive decrease in the friction coefficient was also seen. Copper filler increases hardness and may effectively reduce the temperature at contact interfaces during rotating cycles.
- 28 August 2024
- Published by Springer Nature
- p. 360-367
Preparation and Characterizations of NiCrFeSiAlBC Coatings via a HVOF Process
- 28 August 2024
- Published by Springer Nature
- p. 360-367
Preparation and Characterizations of NiCrFeSiAlBC Coatings via a HVOF Process
- Open Access
- 21 June 2024
- Published by MDPI AG in Lubricants
- Vol. 12 (7) , 231
Microstructural, Mechanical and Tribological Behaviors of Cu/LLDPE-Based Composite Coatings for Lightweight Applications
This research work focuses on the development and analysis of copper-filled linear low-density polyethylene (LLDPE) coatings deposited on LLDPE substrate via a thermocompression process. A dry mechanical mixing technique is employed to mix the copper–LLDPE powders. This relevant technology aims to develop new solid lubricating layered composite coatings without a negative environmental impact. Four different materials of the coatings are considered, i.e., LLDPE + 2 wt.% Cu, LLDPE + 6 wt.% Cu, LLDPE + 10 wt.% Cu and LLDPE + 20 wt.% Cu. The microstructural characterizations indicate a good degree of dispersion and adhesion between the continuous and dispersed phases at 20 wt.% Cu coatings. The mechanical properties of the pure polymer and the fully filled composite materials are investigated experimentally using tensile tests and Micro-Vickers hardness. The stiffness, hardness and mechanical strength of the composites are enhanced. Friction tests are also carried out via a linear reciprocating sliding tribometer. The incorporation of copper powder has a significant improvement on the friction and wear properties of the developed coatings. Higher copper powder loading provides a lower friction coefficient and wear volume loss. The best tribological performances are obtained with the LLDPE + 20 wt.% Cu coating. The wear mechanism of the LLDPE substrate is severe adhesive wear, and it becomes mild abrasive wear in case of the 20 wt.% Cu coating.
- 21 June 2024
- Published by MDPI AG in Lubricants
- Vol. 12 (7) , 231
Open AccessMicrostructural, Mechanical and Tribological Behaviors of Cu/LLDPE-Based Composite Coatings for Lightweight Applications
This research work focuses on the development and analysis of copper-filled linear low-density polyethylene (LLDPE) coatings deposited on LLDPE substrate via a thermocompression process. A dry mechanical mixing technique is employed to mix the copper–LLDPE powders. This relevant technology aims to develop new solid lubricating layered composite coatings without a negative environmental impact. Four different materials of the coatings are considered, i.e., LLDPE + 2 wt.% Cu, LLDPE + 6 wt.% Cu, LLDPE + 10 wt.% Cu and LLDPE + 20 wt.% Cu. The microstructural characterizations indicate a good degree of dispersion and adhesion between the continuous and dispersed phases at 20 wt.% Cu coatings. The mechanical properties of the pure polymer and the fully filled composite materials are investigated experimentally using tensile tests and Micro-Vickers hardness. The stiffness, hardness and mechanical strength of the composites are enhanced. Friction tests are also carried out via a linear reciprocating sliding tribometer. The incorporation of copper powder has a significant improvement on the friction and wear properties of the developed coatings. Higher copper powder loading provides a lower friction coefficient and wear volume loss. The best tribological performances are obtained with the LLDPE + 20 wt.% Cu coating. The wear mechanism of the LLDPE substrate is severe adhesive wear, and it becomes mild abrasive wear in case of the 20 wt.% Cu coating.
- Open Access
On the Structural, Thermal, Micromechanical and Tribological Characterizations of Cu-Filled Acrylonitrile Butadiene Styrene Micro-Composites
The purpose of this work was to investigate the structural, thermal, micromechanical and tribological properties of novel polymer/metal composite materials for bearing applications. Copper (Cu)-filled Acrylonitrile Butadiene Styrene (ABS) composites were mixed in a laboratory scale by an internal mixer with two blade impellers, and then injection-molded. Neat ABS, ABS+5wt% Cu, ABS+10wt% Cu, and ABS+15wt% Cu were the four materials that were tested. The dispersion of Cu particles in the ABS matrix was investigated using Scanning Electron Microscopy (SEM) and a micro-tomography scan. The filler particles have a uniform distribution in the matrix, according to the observations. The incorporation of Cu filler also refined an increase in the glass transition temperature from Differential Scanning Calorimetry (DSC) and less intensity in the amorphous phase by X-ray diffraction (XRD). Nanoindentation tests were carried out to characterize the micro-mechanical behavior of the composites. Friction and wear analysis were also examined using a pin-on-disk tribometer. Compared with neat ABS, all the micro-composites showed much higher indentation hardness, Vickers hardness, and indentation elastic modulus. It was also concluded that the incorporation of Cu filler into ABS simultaneously improved the friction and wear properties of the composites, which contributed to the suitability of the micro-filled composites with hard metallic particles for a wider range of mechanical components for bearing applications.
Open AccessOn the Structural, Thermal, Micromechanical and Tribological Characterizations of Cu-Filled Acrylonitrile Butadiene Styrene Micro-Composites
The purpose of this work was to investigate the structural, thermal, micromechanical and tribological properties of novel polymer/metal composite materials for bearing applications. Copper (Cu)-filled Acrylonitrile Butadiene Styrene (ABS) composites were mixed in a laboratory scale by an internal mixer with two blade impellers, and then injection-molded. Neat ABS, ABS+5wt% Cu, ABS+10wt% Cu, and ABS+15wt% Cu were the four materials that were tested. The dispersion of Cu particles in the ABS matrix was investigated using Scanning Electron Microscopy (SEM) and a micro-tomography scan. The filler particles have a uniform distribution in the matrix, according to the observations. The incorporation of Cu filler also refined an increase in the glass transition temperature from Differential Scanning Calorimetry (DSC) and less intensity in the amorphous phase by X-ray diffraction (XRD). Nanoindentation tests were carried out to characterize the micro-mechanical behavior of the composites. Friction and wear analysis were also examined using a pin-on-disk tribometer. Compared with neat ABS, all the micro-composites showed much higher indentation hardness, Vickers hardness, and indentation elastic modulus. It was also concluded that the incorporation of Cu filler into ABS simultaneously improved the friction and wear properties of the composites, which contributed to the suitability of the micro-filled composites with hard metallic particles for a wider range of mechanical components for bearing applications.