Aron Ringel
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Aron Ringel has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- David Bailly
Institute of Metal Forming (IBF), RWTH Aachen University, Aachen, Germany
3 shared publications David Bailly
2 shared publicationsEmad Scharifi
2 shared publications- Ahmet Zahid Demirezen
RWTH Aachen University
1 shared publication - Andreas Bührig-Polaczek
Foundry Institute, RWTH Aachen University, Aachen, Germany
1 shared publication - D. Bailly
Institute of Metal Forming, RWTH Aachen University, Intzestr. 10, 52072 Aachen, Germany
1 shared publication
Latest Publications
- Open Access
- 15 April 2026
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1185, 55-68
Influences of the Rolling Parameters on Multi-Material Copper-Aluminum Composites via Compound Casting
Multi-material components that consist of copper and aluminum enable the combination of advantageous mechanical, thermal, and electrical properties at competitive cost. While roll bonding is an efficient-solid state joining technique, its implementation requires fully processed, cold-rolled strip material from two process routes. Continuous compound casting in contrast offers a more efficient approach by combining aluminum and copper during casting, followed by flat rolling in a single process route. However, the differences in flow stress between the metals can cause non-uniform elongation and therefore significant shear stresses at the interface during rolling. These stresses may lead to a delamination of the compound if process conditions are not well controlled. This study investigates whether a geometrically structured interface, introduced during compound casting, can contribute to withstanding interfacial shear stresses through mechanical interlocking. In finite element simulations varying process parameters including height reduction, initial temperature, rolling speed ratio, and pass schedule were examined. Results show that a structured interface can effectively resist shear stresses at the copper-aluminum boundary, thereby improving joint stability during deformation. Furthermore, the strain distribution as well as the fluctuation of the shear stresses can be controlled by the process parameters. The findings indicate that the mechanical interlocking by a geometric interface combined with optimized process parameters can enhance the rolling of compound-cast copper-aluminum composites.
- 15 April 2026
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1185, 55-68
Open AccessInfluences of the Rolling Parameters on Multi-Material Copper-Aluminum Composites via Compound Casting
Multi-material components that consist of copper and aluminum enable the combination of advantageous mechanical, thermal, and electrical properties at competitive cost. While roll bonding is an efficient-solid state joining technique, its implementation requires fully processed, cold-rolled strip material from two process routes. Continuous compound casting in contrast offers a more efficient approach by combining aluminum and copper during casting, followed by flat rolling in a single process route. However, the differences in flow stress between the metals can cause non-uniform elongation and therefore significant shear stresses at the interface during rolling. These stresses may lead to a delamination of the compound if process conditions are not well controlled. This study investigates whether a geometrically structured interface, introduced during compound casting, can contribute to withstanding interfacial shear stresses through mechanical interlocking. In finite element simulations varying process parameters including height reduction, initial temperature, rolling speed ratio, and pass schedule were examined. Results show that a structured interface can effectively resist shear stresses at the copper-aluminum boundary, thereby improving joint stability during deformation. Furthermore, the strain distribution as well as the fluctuation of the shear stresses can be controlled by the process parameters. The findings indicate that the mechanical interlocking by a geometric interface combined with optimized process parameters can enhance the rolling of compound-cast copper-aluminum composites.
- Open Access
- 6 April 2026
- Published by Elsevier in Journal of Advanced Joining Processes
- Vol. 13
Assessing the joint strength of a multi-material component by mechanical interlocking of surface structures during cold rolling
- 6 April 2026
- Published by Elsevier in Journal of Advanced Joining Processes
- Vol. 13
Open AccessAssessing the joint strength of a multi-material component by mechanical interlocking of surface structures during cold rolling
- Open Access
- 1 September 2025
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 3104 (1)
Modelling of the Mechanical Interlocking by Surface Structures during Cold Rolling of Multi-Material Components
In sandwich structures, a corrugated core layer is often joined to cover layers along a seam. The lightweight construction potential and high rigidity make such components attractive for a wide range of applications, e.g. for battery housings of electric vehicles. One multi-material approach uses a layer of steel with higher strength for impact protection and an aluminium sheet with low weight and high thermal conductivity for cooling. However, joining of dissimilar materials presents challenges. Metallurgical bonding methods, such as fusion welding, can result in brittle intermetallic phases at the interface. Fasteners like rivets add extra weight and create localized joints only, while adhesives typically exhibit lower strength and adverse aging effects. To overcome these drawbacks, this study proposes a process in which two materials are mechanically joined along a longitudinal seam by cold rolling. First, surface structures with undercuts are rolled into a stronger base material. Secondly, softer material is rolled into the structures. A 2D forming simulation is created to illustrate the rolling of Al99.5 sheets into surface structures on DC04 sheets and experimentally validated. To explore the limits with regard to the strength ratio of the materials two aluminium grades with higher yield strength (AlMg3, AlMg4.5) are selected for simulation and validation experiments. The results indicate that a yield strength ratio exceeding 1.4 is essential for successful joining by cold rolling. At lower ratios, the aluminium flow into the steel’s surface structure is insufficient.
- 1 September 2025
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 3104 (1)
Open AccessModelling of the Mechanical Interlocking by Surface Structures during Cold Rolling of Multi-Material Components
In sandwich structures, a corrugated core layer is often joined to cover layers along a seam. The lightweight construction potential and high rigidity make such components attractive for a wide range of applications, e.g. for battery housings of electric vehicles. One multi-material approach uses a layer of steel with higher strength for impact protection and an aluminium sheet with low weight and high thermal conductivity for cooling. However, joining of dissimilar materials presents challenges. Metallurgical bonding methods, such as fusion welding, can result in brittle intermetallic phases at the interface. Fasteners like rivets add extra weight and create localized joints only, while adhesives typically exhibit lower strength and adverse aging effects. To overcome these drawbacks, this study proposes a process in which two materials are mechanically joined along a longitudinal seam by cold rolling. First, surface structures with undercuts are rolled into a stronger base material. Secondly, softer material is rolled into the structures. A 2D forming simulation is created to illustrate the rolling of Al99.5 sheets into surface structures on DC04 sheets and experimentally validated. To explore the limits with regard to the strength ratio of the materials two aluminium grades with higher yield strength (AlMg3, AlMg4.5) are selected for simulation and validation experiments. The results indicate that a yield strength ratio exceeding 1.4 is essential for successful joining by cold rolling. At lower ratios, the aluminium flow into the steel’s surface structure is insufficient.
- Open Access
Double-Sided Surface Structures with Undercuts on Cold-Rolled Steel Sheets for Interlocking in Hybrid Components
Weight reduction strategies are essential for the transportation sector to reduce greenhouse gas emissions or extend the range of electric vehicles. In the field of lightweight assembly strategies, multi-material design offers great potential. Joining materials typically used in the automotive sector, such as aluminum and steel, brings challenges as conventional processes such as fusion welding are unsuitable. Therefore, new technologies can extend the design options. In previous studies, a mechanical interlocking between cold-rolled surface structures with undercuts on a steel sheet and die-cast aluminum was presented. This method has now been extended to double-sided structures for more complex applications with a joint on both sheet surfaces. Numerical simulations and validation experiments were performed to investigate the manufacturing of the double-sided structures. Furthermore, the influence of the alignment of the upper and lower structures in relation to each other on the resulting structural geometry and the rolling forces were analyzed. More advantageous geometric parameters, e.g., 24% larger undercuts, and approx. 24.1% lower forming forces at 20% height reduction were observed for a shifted alignment. However, significantly higher wear of the structured rollers occurred in the corresponding experiments.
Open AccessDouble-Sided Surface Structures with Undercuts on Cold-Rolled Steel Sheets for Interlocking in Hybrid Components
Weight reduction strategies are essential for the transportation sector to reduce greenhouse gas emissions or extend the range of electric vehicles. In the field of lightweight assembly strategies, multi-material design offers great potential. Joining materials typically used in the automotive sector, such as aluminum and steel, brings challenges as conventional processes such as fusion welding are unsuitable. Therefore, new technologies can extend the design options. In previous studies, a mechanical interlocking between cold-rolled surface structures with undercuts on a steel sheet and die-cast aluminum was presented. This method has now been extended to double-sided structures for more complex applications with a joint on both sheet surfaces. Numerical simulations and validation experiments were performed to investigate the manufacturing of the double-sided structures. Furthermore, the influence of the alignment of the upper and lower structures in relation to each other on the resulting structural geometry and the rolling forces were analyzed. More advantageous geometric parameters, e.g., 24% larger undercuts, and approx. 24.1% lower forming forces at 20% height reduction were observed for a shifted alignment. However, significantly higher wear of the structured rollers occurred in the corresponding experiments.
- Open Access
- 15 May 2024
- Published by Materials Research Forum, LLC in Materials Research Proceedings
- Vol. 41
Influence of cold rolled surface structures with undercuts for interlocking joints on bending processes
-Influence of cold rolled surface structures with undercuts for interlocking joints on bending processes RINGEL Aron, BAILLY David [button link="https://www
- 15 May 2024
- Published by Materials Research Forum, LLC in Materials Research Proceedings
- Vol. 41
Open AccessInfluence of cold rolled surface structures with undercuts for interlocking joints on bending processes
-Influence of cold rolled surface structures with undercuts for interlocking joints on bending processes RINGEL Aron, BAILLY David [button link="https://www
- Open Access
- 9 November 2023
- Published by Springer Nature in International Journal of Material Forming
- Vol. 17 (1) , 1-9
Bending behavior of structured steel sheets with undercuts for interlocking with Al die-cast metal
Due to the current changes in mobility, lightweight design concepts continue to be of particular interest to the automotive industry. One form is the multi-material design, in which the advantageous properties of different materials are combined in one component. In this work, a component made of a steel sheet with stiffening structures of cast aluminum is considered. The joint is created by channel structures with undercuts on the surface of the steel sheet, into which the molten aluminum can flow. After solidification, an interlocking connection is created. The aim of this work is to investigate the influence of a bending operation on the surface structure before the die casting process. Numerical simulations and experimental validations were performed with different bending angles and radii as well as orientations between the channel structure and the punch. The results show that the undercuts on the outer radius are reduced by up to 75% by the bending operation, thus weakening the resulting joint. On the inner radius, the channel opening width narrows by up to 73% and can thus impede the filling with the melt.
- 9 November 2023
- Published by Springer Nature in International Journal of Material Forming
- Vol. 17 (1) , 1-9
Open AccessBending behavior of structured steel sheets with undercuts for interlocking with Al die-cast metal
Due to the current changes in mobility, lightweight design concepts continue to be of particular interest to the automotive industry. One form is the multi-material design, in which the advantageous properties of different materials are combined in one component. In this work, a component made of a steel sheet with stiffening structures of cast aluminum is considered. The joint is created by channel structures with undercuts on the surface of the steel sheet, into which the molten aluminum can flow. After solidification, an interlocking connection is created. The aim of this work is to investigate the influence of a bending operation on the surface structure before the die casting process. Numerical simulations and experimental validations were performed with different bending angles and radii as well as orientations between the channel structure and the punch. The results show that the undercuts on the outer radius are reduced by up to 75% by the bending operation, thus weakening the resulting joint. On the inner radius, the channel opening width narrows by up to 73% and can thus impede the filling with the melt.
- Open Access
Influence of High-Pressure Die Casting Process Parameters on the Compound Strength of Hybrid Components with Undercut Sheet Metal
Reducing the weight of parts through lightweight designs impacts CO2 emissions, especially in the automotive and transportation sectors, which have significant fuel and electric energy consumption. Using multi-material design approaches, specific material properties can be combined to achieve effective lightweighting. Commonly used metals include aluminum, which is known for its high specific strength, and steel, which is valued for its strength and structural integrity. However, joining aluminum and steel presents challenges given their different thermophysical properties and the potential formation of brittle intermetallic phases, making common joining techniques like fusion welding unsuitable. In this study, a hybrid casting process for the production of a complex workpiece from dissimilar materials was investigated. Aluminum was die-cast around a steel sheet insert. Surface structures with undercuts on the steel sheet were applied through modified cold rolling, allowing molten aluminum to flow into the channels and interlock during solidification. It was found that elevated temperatures of the melt and tool were beneficial for the interlocking, resulting in a 30% increase in compound strength. Furthermore, a reduction in both the piston position at the changeover point, between the pre-filling and cavity filling, and the melt velocity at the gate reduced the compound’s strength by 41% and 30%. Up- and downstream processes did not show any significant influence on the conducted experiments. Based on this, two main detrimental effects were observed: pre-solidification of the aluminum melt and gas entrapment.
Open AccessInfluence of High-Pressure Die Casting Process Parameters on the Compound Strength of Hybrid Components with Undercut Sheet Metal
Reducing the weight of parts through lightweight designs impacts CO2 emissions, especially in the automotive and transportation sectors, which have significant fuel and electric energy consumption. Using multi-material design approaches, specific material properties can be combined to achieve effective lightweighting. Commonly used metals include aluminum, which is known for its high specific strength, and steel, which is valued for its strength and structural integrity. However, joining aluminum and steel presents challenges given their different thermophysical properties and the potential formation of brittle intermetallic phases, making common joining techniques like fusion welding unsuitable. In this study, a hybrid casting process for the production of a complex workpiece from dissimilar materials was investigated. Aluminum was die-cast around a steel sheet insert. Surface structures with undercuts on the steel sheet were applied through modified cold rolling, allowing molten aluminum to flow into the channels and interlock during solidification. It was found that elevated temperatures of the melt and tool were beneficial for the interlocking, resulting in a 30% increase in compound strength. Furthermore, a reduction in both the piston position at the changeover point, between the pre-filling and cavity filling, and the melt velocity at the gate reduced the compound’s strength by 41% and 30%. Up- and downstream processes did not show any significant influence on the conducted experiments. Based on this, two main detrimental effects were observed: pre-solidification of the aluminum melt and gas entrapment.