Roberto Jakomin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Roberto Jakomin has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Francesco Pattini
Consiglio Nazionale delle Ricerche, IMEM Institute, 43124 Parma, Italy
2 shared publications - Giulia Spaggiari
Consiglio Nazionale delle Ricerche, IMEM Institute, 43124 Parma, Italy
2 shared publications - Stefano Rampino
Consiglio Nazionale delle Ricerche, IMEM Institute, 43124 Parma, Italy
2 shared publications - Elena Del Canale
Consiglio Nazionale delle Ricerche, IMEM Institute, 43124 Parma, Italy
1 shared publication - Enos Gombia
Consiglio Nazionale delle Ricerche, IMEM Institute, 43124 Parma, Italy
1 shared publication - Francesco Mezzadri
Dipartimento di Scienze Chimiche, della Vita e della Sostenibilità Ambientale & INSTM-UdR Parma, Parco Area delle Scienze, 17/A, Parma 43124, Italy
1 shared publication
Latest Publications
- Open Access
Cu-Doped Sb2Se3 Thin-Film Solar Cells Based on Hybrid Pulsed Electron Deposition/Radio Frequency Magnetron Sputtering Growth Techniques
In recent years, research attention has increasingly focused on thin-film photovoltaics utilizing Sb2Se3 as an ideal absorber layer. This compound is favored due to its abundance, non-toxic nature, long-term stability, and the potential to employ various cost-effective and scalable vapor deposition (PVD) routes. On the other hand, improving passivation, surface treatment and p-type carrier concentration is essential for developing high-performance and commercially viable Sb2Se3 solar cells. In this study, Cu-doped Sb2Se3 solar devices were fabricated using two distinct PVD techniques, pulsed electron deposition (PED) and radio frequency magnetron sputtering (RFMS). Furthermore, 5%Cu:Sb2Se3 films grown via PED exhibited high open-circuit voltages (VOC) of around 400 mV but very low short-circuit current densities (JSC). Conversely, RFMS-grown Sb2Se3 films resulted in low VOC values of around 300 mV and higher JSC. To enhance the photocurrent, we employed strategies involving a thin NaF layer to introduce controlled local doping at the back interface and a bilayer p-doped region grown sequentially using PED and RFMS. The optimized Sb2Se3 bilayer solar cell achieved a maximum efficiency of 5.25%.
Open AccessCu-Doped Sb2Se3 Thin-Film Solar Cells Based on Hybrid Pulsed Electron Deposition/Radio Frequency Magnetron Sputtering Growth Techniques
In recent years, research attention has increasingly focused on thin-film photovoltaics utilizing Sb2Se3 as an ideal absorber layer. This compound is favored due to its abundance, non-toxic nature, long-term stability, and the potential to employ various cost-effective and scalable vapor deposition (PVD) routes. On the other hand, improving passivation, surface treatment and p-type carrier concentration is essential for developing high-performance and commercially viable Sb2Se3 solar cells. In this study, Cu-doped Sb2Se3 solar devices were fabricated using two distinct PVD techniques, pulsed electron deposition (PED) and radio frequency magnetron sputtering (RFMS). Furthermore, 5%Cu:Sb2Se3 films grown via PED exhibited high open-circuit voltages (VOC) of around 400 mV but very low short-circuit current densities (JSC). Conversely, RFMS-grown Sb2Se3 films resulted in low VOC values of around 300 mV and higher JSC. To enhance the photocurrent, we employed strategies involving a thin NaF layer to introduce controlled local doping at the back interface and a bilayer p-doped region grown sequentially using PED and RFMS. The optimized Sb2Se3 bilayer solar cell achieved a maximum efficiency of 5.25%.
- Open Access
Advances on Sb2Se3 Solar Cells Fabricated by Physical Vapor Deposition Techniques
Sb2Se3, as an earth-abundant and low-toxic material, has emerged as one of the most interesting absorbers for clean renewable power generation technologies. Due to its optical properties, especially bandgap and absorption coefficient, the number of papers on Sb2Se3-based solar cells has been constantly increasing in the last ten years, and its power conversion efficiency has raised from 1% in 2014 to 10.57% in 2022. In this review, different Sb2Se3 solar cells’ fabrication technologies based on physical vapor deposition are described and correlated to the texture coefficient (ribbon orientation). Moreover, recent research works of the most promising solar cell configurations with different electron-transporting layers and hole-transporting layers are analyzed with a special emphasis on photovoltaic performances. Furthermore, different Sb2Se3 doping techniques are discussed. All these aspects are considered as new strategies to overcome the Sb2Se3 solar cell’s actual limitations.
Open AccessAdvances on Sb2Se3 Solar Cells Fabricated by Physical Vapor Deposition Techniques
Sb2Se3, as an earth-abundant and low-toxic material, has emerged as one of the most interesting absorbers for clean renewable power generation technologies. Due to its optical properties, especially bandgap and absorption coefficient, the number of papers on Sb2Se3-based solar cells has been constantly increasing in the last ten years, and its power conversion efficiency has raised from 1% in 2014 to 10.57% in 2022. In this review, different Sb2Se3 solar cells’ fabrication technologies based on physical vapor deposition are described and correlated to the texture coefficient (ribbon orientation). Moreover, recent research works of the most promising solar cell configurations with different electron-transporting layers and hole-transporting layers are analyzed with a special emphasis on photovoltaic performances. Furthermore, different Sb2Se3 doping techniques are discussed. All these aspects are considered as new strategies to overcome the Sb2Se3 solar cell’s actual limitations.