Bohdan Fedyshyn
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Bohdan Fedyshyn has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Volodymyr Rashkivskyi
Kyiv National University of Construction and Architecture, Ukraine
8 shared publications - Mykola Prystailo
Kyiv National University of Construction and Architecture Kyiv Povitryanykh Syl Avenue 31 03037
4 shared publications - Maksym Balaka
Київський національний університет будівництва і архітектури
2 shared publications - Oleksandr Teteriatnyk
Київський національний університет будівництва та архітектури
2 shared publications - Iryna Dubovyk
Kyiv National University of Construction and Architecture
1 shared publication - Leonid Pelevin
Kyiv National University of Construction and Architecture 31, Povitroflotskyi Avenue 03037 Kyiv Ukraine
1 shared publication
Latest Publications
- Open Access
- 26 July 2026
- Published by Kyiv National University of Construction and Architecture in Gіrnichі, budіvelnі, dorozhnі ta melіorativnі mashini
- No. 107,p. 43-50
Development and computer simulation of bulldozer blade equipment with a hydraulic heating system
The paper presents the development and numerical verification of a bulldozer blade equipped with an integrated hydraulic heating system for operation under low-temperature conditions. The study addresses the adhesion and freezing of wet soil on the metal surface of blade equipment, which distort the designed geometry of the working body, increase cutting and dragging resistance, reduce productivity, raise fuel consumption and cause downtime for manual cleaning. A semi-universal blade designed with tubular heat-exchange channels arranged on the rear side of the front sheet, supply and return manifolds, thermal insulation and protective elements. Heated hydraulic fluid from the machine hydraulic system selected as the heat carrier, allowing part of the energy normally dissipated through the radiator to be reused. The main thermal and hydraulic parameters of the system were substantiated. The required thermal power with a design margin is 8.1 kW, while the recommended fluid flow rate is approximately 20 L/min. To verify the proposed design, a three-dimensional blade model was created and analysed in the SimScale CAE environment. The simulation included boundary conditions corresponding to a heat-carrier temperature of 60 °C, an ambient temperature of −20 °C and a heat-transfer coefficient of 10 W/(m²·K). The obtained temperature field confirmed that a positive temperature can be maintained over the main working area and revealed increased heat losses near the cutting edge. The results justify the selected channel arrangement and indicate the need for denser channel placement in the lower zone. The developed solution can be implemented as a modernisation of serial bulldozer blade equipment to improve winter operating efficiency.
- 26 July 2026
- Published by Kyiv National University of Construction and Architecture in Gіrnichі, budіvelnі, dorozhnі ta melіorativnі mashini
- No. 107,p. 43-50
Open AccessDevelopment and computer simulation of bulldozer blade equipment with a hydraulic heating system
The paper presents the development and numerical verification of a bulldozer blade equipped with an integrated hydraulic heating system for operation under low-temperature conditions. The study addresses the adhesion and freezing of wet soil on the metal surface of blade equipment, which distort the designed geometry of the working body, increase cutting and dragging resistance, reduce productivity, raise fuel consumption and cause downtime for manual cleaning. A semi-universal blade designed with tubular heat-exchange channels arranged on the rear side of the front sheet, supply and return manifolds, thermal insulation and protective elements. Heated hydraulic fluid from the machine hydraulic system selected as the heat carrier, allowing part of the energy normally dissipated through the radiator to be reused. The main thermal and hydraulic parameters of the system were substantiated. The required thermal power with a design margin is 8.1 kW, while the recommended fluid flow rate is approximately 20 L/min. To verify the proposed design, a three-dimensional blade model was created and analysed in the SimScale CAE environment. The simulation included boundary conditions corresponding to a heat-carrier temperature of 60 °C, an ambient temperature of −20 °C and a heat-transfer coefficient of 10 W/(m²·K). The obtained temperature field confirmed that a positive temperature can be maintained over the main working area and revealed increased heat losses near the cutting edge. The results justify the selected channel arrangement and indicate the need for denser channel placement in the lower zone. The developed solution can be implemented as a modernisation of serial bulldozer blade equipment to improve winter operating efficiency.
- Open Access
- 26 July 2026
- Published by Kyiv National University of Construction and Architecture in Gіrnichі, budіvelnі, dorozhnі ta melіorativnі mashini
- No. 107,p. 35-42
Analysis of calculation methods and selection recommendations for rational surcharge loading devices in concrete compaction
The article presents a comprehensive review of calculation methods for surcharge (preloading) devices (static, pneumatic, and vibratory) used in the compaction of stiff concrete mixtures on vibrating platforms. Experimental and theoretical studies demonstrating a significant variability in the recommended surcharge pressure—ranging from 0.02 kPa to 40 kPa depending on experimental conditions, mixture stiffness, and equipment type—are analyzed. It is shown that most existing methodologies are based on the simplified assumption of a purely static loading effect and do not account for the dynamic properties of the concrete mixture, resonance phenomena, or the mass–inertia characteristics of the “vibrating platform – concrete mixture – surcharge device” system. The limitations of determining parameters based solely on static pressure substantiated. The analysis demonstrates that optimal compaction efficiency is primarily governed by dynamic interaction conditions, including resonance modes, phase relationships, and vibration amplitude preservation, rather than the magnitude of static pressure. Particular attention paid to pneumatic and vibratory devices, which enable controlled adjustment of loading and facilitate energetically favorable operating regimes. Rational approaches to selecting the type and magnitude of surcharge loading proposed, taking into account mixture stiffness, compacted layer height, and vibration system parameters. The formulated recommendations can be apply to optimize technological compaction regimes, improve concrete homogeneity, and increase the energy efficiency and operational reliability of vibration equipment.
- 26 July 2026
- Published by Kyiv National University of Construction and Architecture in Gіrnichі, budіvelnі, dorozhnі ta melіorativnі mashini
- No. 107,p. 35-42
Open AccessAnalysis of calculation methods and selection recommendations for rational surcharge loading devices in concrete compaction
The article presents a comprehensive review of calculation methods for surcharge (preloading) devices (static, pneumatic, and vibratory) used in the compaction of stiff concrete mixtures on vibrating platforms. Experimental and theoretical studies demonstrating a significant variability in the recommended surcharge pressure—ranging from 0.02 kPa to 40 kPa depending on experimental conditions, mixture stiffness, and equipment type—are analyzed. It is shown that most existing methodologies are based on the simplified assumption of a purely static loading effect and do not account for the dynamic properties of the concrete mixture, resonance phenomena, or the mass–inertia characteristics of the “vibrating platform – concrete mixture – surcharge device” system. The limitations of determining parameters based solely on static pressure substantiated. The analysis demonstrates that optimal compaction efficiency is primarily governed by dynamic interaction conditions, including resonance modes, phase relationships, and vibration amplitude preservation, rather than the magnitude of static pressure. Particular attention paid to pneumatic and vibratory devices, which enable controlled adjustment of loading and facilitate energetically favorable operating regimes. Rational approaches to selecting the type and magnitude of surcharge loading proposed, taking into account mixture stiffness, compacted layer height, and vibration system parameters. The formulated recommendations can be apply to optimize technological compaction regimes, improve concrete homogeneity, and increase the energy efficiency and operational reliability of vibration equipment.
- Open Access
- 2 April 2025
- Published by Kyiv National University of Construction and Architecture in Gіrnichі, budіvelnі, dorozhnі ta melіorativnі mashini
- No. 105,p. 62-72
Results of experimental studies of cutting soils with spatially oriented knives of blade equipment
To carry out experimental studies of the process of cutting the working environment by spatially oriented blades of blade equipment, the dynamometric stand for registering the force load of the author's design of KNUBA was improved, which allowed to conduct full-fledged experimental studies taking into account all the existing factors of interaction between the working environment and the working body during cutting. The use of soils of III, IV, and V categories is proposed as a working environment. As a result of the studies carried out for the dynamometric stand for recording the force load during the study of the cutting process with a spatially oriented knife, the cutting forces at different angles α of its deviation were analytically determined, which perform the work of destroying and overcoming the soil resistance to cutting. According to the results of theoretical studies, it was found that the limits of the cutting force determined for a natural installation with spatially oriented knives and for a laboratory bench are the same, and the nature of their change is also similar and is related to each other by the similarity coefficient. In order to verify the adequacy of theoretical calculations on the dynamometer bench, experimental studies of cutting the working environment were carried out. In the course of experimental studies, normal and orthogonal forces were measured simultaneously, which perform the work of destruction and overcoming the resistance of the soil to cutting. The experimental studies carried out fully confirm the adequacy of theoretical calculations, and the comparison of theoretical and experimental results of determining the cutting force showed their sufficient convergence and, accordingly, the legitimacy of using analytical expressions in calculating the power parameters of machines with spatially oriented knifes of blade equipment. The values of the cutting forces that perform the work of destroying and overcoming the resistance of the soil to cutting, which were determined theoretically, taking into account the similarity coefficients used in physical modelling for the above laboratory stand for recording cutting forces by spatially oriented knife of blade equipment, are compared with the results of the cutting forces determined experimentally on this stand. The maximum value of the error in determining the cutting force by theoretical and experimental methods on the laboratory stand for recording cutting forces by spatially oriented knife of blade equipment is Δδ=10,06%.
- 2 April 2025
- Published by Kyiv National University of Construction and Architecture in Gіrnichі, budіvelnі, dorozhnі ta melіorativnі mashini
- No. 105,p. 62-72
Open AccessResults of experimental studies of cutting soils with spatially oriented knives of blade equipment
To carry out experimental studies of the process of cutting the working environment by spatially oriented blades of blade equipment, the dynamometric stand for registering the force load of the author's design of KNUBA was improved, which allowed to conduct full-fledged experimental studies taking into account all the existing factors of interaction between the working environment and the working body during cutting. The use of soils of III, IV, and V categories is proposed as a working environment. As a result of the studies carried out for the dynamometric stand for recording the force load during the study of the cutting process with a spatially oriented knife, the cutting forces at different angles α of its deviation were analytically determined, which perform the work of destroying and overcoming the soil resistance to cutting. According to the results of theoretical studies, it was found that the limits of the cutting force determined for a natural installation with spatially oriented knives and for a laboratory bench are the same, and the nature of their change is also similar and is related to each other by the similarity coefficient. In order to verify the adequacy of theoretical calculations on the dynamometer bench, experimental studies of cutting the working environment were carried out. In the course of experimental studies, normal and orthogonal forces were measured simultaneously, which perform the work of destruction and overcoming the resistance of the soil to cutting. The experimental studies carried out fully confirm the adequacy of theoretical calculations, and the comparison of theoretical and experimental results of determining the cutting force showed their sufficient convergence and, accordingly, the legitimacy of using analytical expressions in calculating the power parameters of machines with spatially oriented knifes of blade equipment. The values of the cutting forces that perform the work of destroying and overcoming the resistance of the soil to cutting, which were determined theoretically, taking into account the similarity coefficients used in physical modelling for the above laboratory stand for recording cutting forces by spatially oriented knife of blade equipment, are compared with the results of the cutting forces determined experimentally on this stand. The maximum value of the error in determining the cutting force by theoretical and experimental methods on the laboratory stand for recording cutting forces by spatially oriented knife of blade equipment is Δδ=10,06%.
- Open Access
- 1 February 2025
- Published by International Science Group in International Science Journal of Engineering & Agriculture
- Vol. 4 (1) , 79-92
Methods of conducting a bench-scale experimental study with a spatially oriented knife of a bulldozer blade
The paper considers the assessment of the interaction of a spatially oriented knife of a bulldozer blade with the working environment, which was carried out on the basis of a one-factor experiment using high-tech measuring and recording equipment, which allowed to quickly obtain accurate results from the primary data. Oscillogram processing consisted of determining the average maximum ordinate of the cutting force P and finding its value. Thanks to the use of the designed and developed high-precision control system for feeding and transverse movement of the working body and high-tech measuring and recording equipment, which allows to quickly and without repetition obtain sufficiently accurate estimates of the interaction of the spatially oriented blade of the bulldozer blade with the working environment from the primary data and made it possible to process them using modern software, which eliminated the time-consuming data processing process. This, in turn, made it possible to minimise the number of measurements of the cutting force at a given accuracy and reliability of the test results with a data probability of 0,9 to 0,95.
- 1 February 2025
- Published by International Science Group in International Science Journal of Engineering & Agriculture
- Vol. 4 (1) , 79-92
Open AccessMethods of conducting a bench-scale experimental study with a spatially oriented knife of a bulldozer blade
The paper considers the assessment of the interaction of a spatially oriented knife of a bulldozer blade with the working environment, which was carried out on the basis of a one-factor experiment using high-tech measuring and recording equipment, which allowed to quickly obtain accurate results from the primary data. Oscillogram processing consisted of determining the average maximum ordinate of the cutting force P and finding its value. Thanks to the use of the designed and developed high-precision control system for feeding and transverse movement of the working body and high-tech measuring and recording equipment, which allows to quickly and without repetition obtain sufficiently accurate estimates of the interaction of the spatially oriented blade of the bulldozer blade with the working environment from the primary data and made it possible to process them using modern software, which eliminated the time-consuming data processing process. This, in turn, made it possible to minimise the number of measurements of the cutting force at a given accuracy and reliability of the test results with a data probability of 0,9 to 0,95.
- Open Access
- 29 November 2024
- Published by Kyiv National University of Construction and Architecture in Strength of Materials and Theory of Structures
- No. 113,p. 285-296
Development and computer testing of equipment for cutting soils with spatially oriented knives of a bulldozer blade
The paper uses approaches to the creation and computer testing of a model of an experimental installation for cutting soil with spatially oriented working bodies of earthmoving machines used on construction sites. Today, there is a need for the efficient performance of construction work related to the operation of construction machinery with blade equipment. This, in turn, poses the task of determining the productivity of mechanized earthworks in various working environments. The main method of mechanical soil development is cutting. The main geometric conditions are the position of the cutting wedge edge relative to the cutting direction and the surface of the massif, the contour of the cutting edge, the contour and number of working surfaces of the cutting wedge, the number of so-called side cutting surfaces and the so-called blocked cutting surfaces. The peculiarity of the digging process is that its power and energy indicators depend on the kinematic conditions and geometric parameters - thickness, width and cut area, as well as on the angles of orientation of the working body in space. The creation of such a computer model of the experimental setup is due to the need for continuous improvement of existing equipment and the creation of new equipment to meet existing needs. The model of the experimental setup was created in accordance with the working hypothesis, where the movement of the spatially oriented knife occurs perpendicular to the movement of the blade equipment, at different ratios of the speed of the blade and the movement of the knife, which creates a simple interaction with the working environment, and the deviation of the application of the full cutting force by an angle α. According to the working hypothesis, depending on the plan of movement of the spatially oriented knife, its geometric interaction with the working environment changes and the cutting force changes accordingly. The necessity to create more productive and efficient earthmoving equipment requires the use of modern design solutions. Using the calculations of soil cutting by spatially oriented earthmoving tools in the form of a dihedral blade of dump equipment, a computer study of stress equivalents, linear displacement, yield strength factor, tensile strength factor, and loss of stability factor was carried out. The results are summarized in the form of tabular data and graphical display.
- 29 November 2024
- Published by Kyiv National University of Construction and Architecture in Strength of Materials and Theory of Structures
- No. 113,p. 285-296
Open AccessDevelopment and computer testing of equipment for cutting soils with spatially oriented knives of a bulldozer blade
The paper uses approaches to the creation and computer testing of a model of an experimental installation for cutting soil with spatially oriented working bodies of earthmoving machines used on construction sites. Today, there is a need for the efficient performance of construction work related to the operation of construction machinery with blade equipment. This, in turn, poses the task of determining the productivity of mechanized earthworks in various working environments. The main method of mechanical soil development is cutting. The main geometric conditions are the position of the cutting wedge edge relative to the cutting direction and the surface of the massif, the contour of the cutting edge, the contour and number of working surfaces of the cutting wedge, the number of so-called side cutting surfaces and the so-called blocked cutting surfaces. The peculiarity of the digging process is that its power and energy indicators depend on the kinematic conditions and geometric parameters - thickness, width and cut area, as well as on the angles of orientation of the working body in space. The creation of such a computer model of the experimental setup is due to the need for continuous improvement of existing equipment and the creation of new equipment to meet existing needs. The model of the experimental setup was created in accordance with the working hypothesis, where the movement of the spatially oriented knife occurs perpendicular to the movement of the blade equipment, at different ratios of the speed of the blade and the movement of the knife, which creates a simple interaction with the working environment, and the deviation of the application of the full cutting force by an angle α. According to the working hypothesis, depending on the plan of movement of the spatially oriented knife, its geometric interaction with the working environment changes and the cutting force changes accordingly. The necessity to create more productive and efficient earthmoving equipment requires the use of modern design solutions. Using the calculations of soil cutting by spatially oriented earthmoving tools in the form of a dihedral blade of dump equipment, a computer study of stress equivalents, linear displacement, yield strength factor, tensile strength factor, and loss of stability factor was carried out. The results are summarized in the form of tabular data and graphical display.
- Open Access
- 18 September 2024
- Published by Kyiv National University of Construction and Architecture in Gіrnichі, budіvelnі, dorozhnі ta melіorativnі mashini
- No. 103,p. 45-54
Development and construction of a mechanized moving platform for human service
The purpose of the proposed article is the development and construction of a mechanized mobile platform for serving people, which is caused by the need to increase the safety of the operation of such technical means, in particular, in the case of the need for mass customer service. The methodology is based on search, research and creative approaches. The methods of development analysis, patent search, synthesis of technical solutions, simulation modelling was used. Scientific novelty. The study of the features of various approaches to the creation of effective mechanized moving platforms, the analysis of solutions and the dynamics of patenting made it possible to substantiate the directions of development of technical solutions and the prospects of developments. The authors proposed constructive solutions for mobile platforms, developed approaches to the technical implementation of increasing the safety of their operation, proposed energy-saving approaches aimed at reducing the energy consumption of mechanized means, which is especially relevant in the mass implementation of platforms for serving people. Research results. The article solves important safety issues of human service, in particular in the entertainment industry through the development of structural parts, drives and rules for the operation of mechanized moving platforms. Synthesized constructive solutions obtained in the course of patent research, analysis of modern technical solutions, rational technical design, and expert evaluation are presented. It was determined that the safety of the operation of mechanized moving platforms, which are intended for the transport of people in the field of tourism, depends on effective approaches to the design and components of the technical system in the form of a moving platform, its structural components, elements of its mechanism and the drive system as a whole, which with the optimization of technical indicators the stability of the overall system, the smoothness of movement and braking of the platform, the optimization of the materiality of the structure in total allow to have a qualitative effect on improving the safety of human operation.
- 18 September 2024
- Published by Kyiv National University of Construction and Architecture in Gіrnichі, budіvelnі, dorozhnі ta melіorativnі mashini
- No. 103,p. 45-54
Open AccessDevelopment and construction of a mechanized moving platform for human service
The purpose of the proposed article is the development and construction of a mechanized mobile platform for serving people, which is caused by the need to increase the safety of the operation of such technical means, in particular, in the case of the need for mass customer service. The methodology is based on search, research and creative approaches. The methods of development analysis, patent search, synthesis of technical solutions, simulation modelling was used. Scientific novelty. The study of the features of various approaches to the creation of effective mechanized moving platforms, the analysis of solutions and the dynamics of patenting made it possible to substantiate the directions of development of technical solutions and the prospects of developments. The authors proposed constructive solutions for mobile platforms, developed approaches to the technical implementation of increasing the safety of their operation, proposed energy-saving approaches aimed at reducing the energy consumption of mechanized means, which is especially relevant in the mass implementation of platforms for serving people. Research results. The article solves important safety issues of human service, in particular in the entertainment industry through the development of structural parts, drives and rules for the operation of mechanized moving platforms. Synthesized constructive solutions obtained in the course of patent research, analysis of modern technical solutions, rational technical design, and expert evaluation are presented. It was determined that the safety of the operation of mechanized moving platforms, which are intended for the transport of people in the field of tourism, depends on effective approaches to the design and components of the technical system in the form of a moving platform, its structural components, elements of its mechanism and the drive system as a whole, which with the optimization of technical indicators the stability of the overall system, the smoothness of movement and braking of the platform, the optimization of the materiality of the structure in total allow to have a qualitative effect on improving the safety of human operation.
- Open Access
- 31 December 2023
- Published by Kyiv National University of Construction and Architecture in Transfer of innovative technologies
- p. 58-70
Modelling of soil destruction process by bulldozer using a spatially oriented working unit
The article uses approaches to creating a model for calculating soil cutting forces by spatially oriented working units of construction machines used on construction sites. The use of such a model is due to the need for continuous improvement of existing equipment and the creation of new ones, taking into account the existing needs. Today, there is a need for efficient performance of construction works related to the operation of construction equipment with dumping equipment. This, in turn, poses the task of determining the performance of mechanised earthworks in various working environments, one of the most common in Ukraine being marl clay, loam and argillaceous clay. The main method of mechanical soil development is cutting. The main geometric conditions are the position of the cutting wedge edge relative to the cutting direction and the surface of the massif, the outline of the cutting edge, the outline and number of working surfaces of the cutting wedge, the number of so-called side cut surfaces and the so-called blocked cut surfaces. The peculiarity of the digging process is that its power and energy indicators depend on the kinematic conditions and geometric parameters – thickness, width and area of the cut, as well as on the angles of orientation of the working unit in space. The computational model was created in accordance with the working hypothesis, where the movement of spatially oriented knives moves perpendicular to the blade equipment, at different ratios of the blade movement speed and knife movement, which creates spatial interaction with the working environment, and the deviation of the application of the full cutting force by an angle α. In accordance with the working hypothesis, we obtained five plans for the movement of the spatially oriented blade of the blade. Depending on the plan of movement of the spatially oriented knife, its geometric interaction with the working environment changes and the cutting force changes accordingly. The need to create more productive and efficient earthmoving equipment requires the use of modern design solutions. In the course of the study, a model for calculating the cutting of soils by spatially oriented earthmoving tools in the form of a dihedral knife of dump equipment was created. A comparison of soil cutting forces at different depths during the operation of a spatially oriented working body is also proposed. The results are summarised in the form of tabular data and graphs.
- 31 December 2023
- Published by Kyiv National University of Construction and Architecture in Transfer of innovative technologies
- p. 58-70
Open AccessModelling of soil destruction process by bulldozer using a spatially oriented working unit
The article uses approaches to creating a model for calculating soil cutting forces by spatially oriented working units of construction machines used on construction sites. The use of such a model is due to the need for continuous improvement of existing equipment and the creation of new ones, taking into account the existing needs. Today, there is a need for efficient performance of construction works related to the operation of construction equipment with dumping equipment. This, in turn, poses the task of determining the performance of mechanised earthworks in various working environments, one of the most common in Ukraine being marl clay, loam and argillaceous clay. The main method of mechanical soil development is cutting. The main geometric conditions are the position of the cutting wedge edge relative to the cutting direction and the surface of the massif, the outline of the cutting edge, the outline and number of working surfaces of the cutting wedge, the number of so-called side cut surfaces and the so-called blocked cut surfaces. The peculiarity of the digging process is that its power and energy indicators depend on the kinematic conditions and geometric parameters – thickness, width and area of the cut, as well as on the angles of orientation of the working unit in space. The computational model was created in accordance with the working hypothesis, where the movement of spatially oriented knives moves perpendicular to the blade equipment, at different ratios of the blade movement speed and knife movement, which creates spatial interaction with the working environment, and the deviation of the application of the full cutting force by an angle α. In accordance with the working hypothesis, we obtained five plans for the movement of the spatially oriented blade of the blade. Depending on the plan of movement of the spatially oriented knife, its geometric interaction with the working environment changes and the cutting force changes accordingly. The need to create more productive and efficient earthmoving equipment requires the use of modern design solutions. In the course of the study, a model for calculating the cutting of soils by spatially oriented earthmoving tools in the form of a dihedral knife of dump equipment was created. A comparison of soil cutting forces at different depths during the operation of a spatially oriented working body is also proposed. The results are summarised in the form of tabular data and graphs.
- Open Access
- 25 December 2023
- Published by Kyiv National University of Construction and Architecture in Gіrnichі, budіvelnі, dorozhnі ta melіorativnі mashini
- No. 102,p. 24-30
Development of the information model of the soil cutting process spatially oriented knife of dynamic action
The results of the construction of an information model of the process of soil cutting with straight-furrow oriented knives of dynamic action are given. Bulldozer equipment and its main tasks are considered. A working hypothesis of the movement of the scraper and the vertically oriented knife has been formed. The working hypothesis is based on the fact that the movement of the spatially oriented knife will be carried out longitudinally - translationally, perpendicular to the trajectory of the movement of the working body. The dynamic movement of the knife will be carried out with the help of a self-oscillating hydraulic vibrator, the development of such a solution was implemented at the Department of Construction Machinery of KNUСA, the prerequisites were the work of the team, in particular, prof. Smirnov V.M. regarding the structure of the working body and prof. Baladinsky V.M. regarding the regularities of creating dynamic movements of cutting elements of earth-moving machines. And also, based on the works of Khmara L.A., candidate in connection with the intensification of the mechanization of earthworks in construction. Their vector movement and determination of the angles of application of the main cutting force to the corresponding angle α are presented. After constructing the movement vectors of the working body and the spatially oriented knife, a method of calculating the direction of the cutting force and the deflection angle α was developed. Using vector sums and speed ratios ranging from 10:1, where the spatially oriented knife moves ten times faster than the blade, to 1:10, where the spatially oriented knife moves ten times slower. A graph of the determination of the angle α is plotted depending on the ratio of the blade feeding speeds and the displacement of the spatially oriented knife. The speed ratio is calculated and entered in the speed ratio table according to the angle α and the bulldozer's gear ratio.
- 25 December 2023
- Published by Kyiv National University of Construction and Architecture in Gіrnichі, budіvelnі, dorozhnі ta melіorativnі mashini
- No. 102,p. 24-30
Open AccessDevelopment of the information model of the soil cutting process spatially oriented knife of dynamic action
The results of the construction of an information model of the process of soil cutting with straight-furrow oriented knives of dynamic action are given. Bulldozer equipment and its main tasks are considered. A working hypothesis of the movement of the scraper and the vertically oriented knife has been formed. The working hypothesis is based on the fact that the movement of the spatially oriented knife will be carried out longitudinally - translationally, perpendicular to the trajectory of the movement of the working body. The dynamic movement of the knife will be carried out with the help of a self-oscillating hydraulic vibrator, the development of such a solution was implemented at the Department of Construction Machinery of KNUСA, the prerequisites were the work of the team, in particular, prof. Smirnov V.M. regarding the structure of the working body and prof. Baladinsky V.M. regarding the regularities of creating dynamic movements of cutting elements of earth-moving machines. And also, based on the works of Khmara L.A., candidate in connection with the intensification of the mechanization of earthworks in construction. Their vector movement and determination of the angles of application of the main cutting force to the corresponding angle α are presented. After constructing the movement vectors of the working body and the spatially oriented knife, a method of calculating the direction of the cutting force and the deflection angle α was developed. Using vector sums and speed ratios ranging from 10:1, where the spatially oriented knife moves ten times faster than the blade, to 1:10, where the spatially oriented knife moves ten times slower. A graph of the determination of the angle α is plotted depending on the ratio of the blade feeding speeds and the displacement of the spatially oriented knife. The speed ratio is calculated and entered in the speed ratio table according to the angle α and the bulldozer's gear ratio.
- Open Access
- 24 November 2023
- Published by Kyiv National University of Construction and Architecture in Strength of Materials and Theory of Structures
- No. 111,p. 263-275
Development of a parametric model of the spatially oriented knife on the bulldozer blade
The paper considers the results of the study of resistances arising during the operation of a bulldozer in the soil environment and processes in the drawing prism. What affects the stability and productivity of the bulldozer during excavation works. The geological map of the "Ukrainian crystalline shield" was studied, where the most common soils on the territory of Ukraine were found. Using the proposed hypothesis of the movement of spatially oriented knives on a bulldozer blade, it was shown that when excavating soil at different speed ratios, there is a deviation of the cutting force application vector by an angle (α), which in turn affects the geometric interaction of the spatially oriented knife with the working environment. Changing the geometric interaction of the spatially oriented knife with the soil affects the cutting force, which led to the creation of a parametric model of the interaction of spatially oriented knives with the working environment. The model was developed for different knife configurations and different ratios of the bulldozer speed to the spatially oriented knife movement speed. The total, normal, and orthogonal cutting forces for the working, subcritical, and critical depths of soil cutting were calculated, according to changes in the parametric model of the spatially oriented knife. A comparative calculation of the cutting force by a bulldozer without and with spatially oriented knives was carried out.
- 24 November 2023
- Published by Kyiv National University of Construction and Architecture in Strength of Materials and Theory of Structures
- No. 111,p. 263-275
Open AccessDevelopment of a parametric model of the spatially oriented knife on the bulldozer blade
The paper considers the results of the study of resistances arising during the operation of a bulldozer in the soil environment and processes in the drawing prism. What affects the stability and productivity of the bulldozer during excavation works. The geological map of the "Ukrainian crystalline shield" was studied, where the most common soils on the territory of Ukraine were found. Using the proposed hypothesis of the movement of spatially oriented knives on a bulldozer blade, it was shown that when excavating soil at different speed ratios, there is a deviation of the cutting force application vector by an angle (α), which in turn affects the geometric interaction of the spatially oriented knife with the working environment. Changing the geometric interaction of the spatially oriented knife with the soil affects the cutting force, which led to the creation of a parametric model of the interaction of spatially oriented knives with the working environment. The model was developed for different knife configurations and different ratios of the bulldozer speed to the spatially oriented knife movement speed. The total, normal, and orthogonal cutting forces for the working, subcritical, and critical depths of soil cutting were calculated, according to changes in the parametric model of the spatially oriented knife. A comparative calculation of the cutting force by a bulldozer without and with spatially oriented knives was carried out.