DMDaria A. Makarova

Daria A. Makarova

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Daria A. Makarova has a total of 24 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Speed profile optimisation for a semi-trailer truck based on a hybrid fuel consumption model with automatic calibration based on CAN bus data

    by Artem S. Dubrovskii, Sergey S. Shadrin, Daria A. Makarova, Yury M. Furletov

    The paper proposes a method for optimising the speed profile of a long-haul semi-trailer truck that combines a physical fuel consumption model with a machine-learning correction with automatic calibration using on-board CAN bus data. The physical component is built on the tractive balance equation, which parameters, i.e. the power transmission efficiency, rolling resistance coefficient, brake-specific fuel consumption and lumped mechanical losses, are identified without bench testing by minimising the difference between the computed and the measured instantaneous fuel rate using the Powell's method; calibration is verified against the cumulative fuel counter (SAE J1939). The correction is implemented with the LightGBM algorithm that approximates the rest of the physical model; for the first time the current gear signal extracted directly from the CAN bus is used as an additional feature. The optimal speed profile is obtained by dynamic programming subject to a constraint on the travel-time increase; the speed range is lumped into 13 values within 60–80 km/h. The method was verified using a field trial with a Mercedes-Benz Actros 1845 truck on the M-11 «Neva» motorway (Moscow – Saint Petersburg, 672.5 km; about 14 million CAN records processed in under two minutes). The calibration error was 3.6%; introduction of the gear feature reduced the prediction root-mean-square error from 13.7 to 11.5 L/100 km (by 16%) and the cumulative-consumption deviation down to 1.4%. The computed fuel saving reached 9.3% at the travel time increased by less than 0.6%. Numerical simulation using the Moscow – Kazan route (809.1 km) confirmed the scalability: a 10.4% saving at a 2.8% time increase without model re-calibration.

  • Open Access

    A Comprehensive Safety Assessment Methodology for Highly Automated Vehicles in Operation: Development and Demonstration Based on Road Test Data

    by Daria Makarova, Sergey Shadrin, Andrey Keller, Yury Furletov

    The article presents a comprehensive methodology for assessing the safety of highly automated vehicles (HAVs) based on operational data collected on public roads. The methodology includes a qualitative classification of safety violations according to three criteria: impact on functionality, extent of coverage by safety mechanisms, and frequency of occurrence. Based on the sum of these criteria, a criticality matrix is constructed, distinguishing four risk zones: critical (requiring immediate remediation), unacceptable (requiring planned remediation), tolerable, and acceptable. The quantitative assessment includes a system of key performance indicators (operational efficiency, number of accidents, detection and elimination of threats, and frequency of driver/operator interventions) and an integral safety indicator. The applicability of the methodology was demonstrated using operational data from a Level 3 HAV collected over 1413 km of automated driving on Russian highways. In this demonstration, most of the recorded failures were classified in the critical zone, which made it possible to prioritize system improvements. The proposed methodology can be used by developers for the objective assessment of safety and by regulators for developing reporting requirements. From the perspective of sensor and actuator networks, this work makes three contributions: (1) the multimodal sensor network of the HAV (4 cameras, 4 radars, GNSS RTK) is analyzed as a networked system with redundancy and overlapping fields of view; (2) the CAN bus is treated as an actuator network whose reliability is critical for safety; (3) it is shown that 10 of 17 recorded failures (59%) are related specifically to network equipment, making the monitoring of sensor and actuator networks a central element of the proposed methodology.

  • Архитектура сбора и передачи телематических данных для интеллектуальных транспортных систем магистрального автотранспорта

    by Артем Семенович Дубровский, Сергей Сергеевич Шадрин, Дарья Алексеевна Макарова, Андрей Владимирович Келлер, Юрий Михайлович Фурлетов

    Развитие интеллектуальных транспортных систем для магистрального грузового автотранспорта требует надёжной инфраструктуры сбора, передачи и хранения телематических данных, а также точных цифровых моделей автомобильных дорог, без которых расчёт энергетических затрат на движение и построение адаптивных алгоритмов управления теряют практический смысл. В большинстве публикаций, посвящённых энергоэффективному управлению грузовым транспортом, телематическая подсистема описывается фрагментарно – как источник сигналов CAN-шины и GPS-трека, – без раскрытия архитектуры передачи, протоколов и методологии построения цифровой модели дороги. В настоящей работе разработана и описана трёхуровневая архитектура сбора, передачи и хранения телематических данных, включающая бортовой уровень интеграции с сетями CAN по стандарту SAE J1939, уровень оперативной обработки с навигационной привязкой по каналу Bluetooth Low Energy, а также облачную платформу с типизированным бинарным протоколом поверх TCP/IP и колоночно-ориентированной моделью хранения. Для построения цифровой модели автомобильной дороги использована методика высокоточного картирования, дополненная коррекцией по глобальной модели рельефа методом сплайн-интерполяции, что обеспечивает относительную точность модели не хуже 0,4 м при дискретности опорных точек маршрута в 2 м. Систематизированы факторы внешней среды и предложены принципы их интеграции в архитектуру данных и концепцию интеллектуальной транспортной системы, включая использование каналов V2X для перехода от статической цифровой модели маршрута к адаптивному синтезу решений в реальном времени. Практическая апробация на натурном эксперименте с магистральным автопоездом КАМАЗ-54901-92 на маршруте Р-22 «Каспий» (408 км) подтвердила работоспособность предложенных решений, позволяющих рассматривать их как самостоятельный телематический модуль для интеграции в платформы логистических операторов и системы поддержки принятия решений водителя. The development of intelligent transportation systems for long-haul freight transport requires a reliable infrastructure for telematics data acquisition, transmission and storage, as well as accurate digital road models, without which the calculation of driving energy costs and the design of adaptive control algorithms lose practical value. Most publications on energy-efficient truck management describe the telematics subsystem only fragmentarily – as a source of CAN-bus signals and a GPS track – without disclosing the transmission architecture, protocols, or the methodology used to build the digital road model. In this study, a three-tier telematics data acquisition and transmission architecture is developed and described, comprising the on-board integration layer with CAN networks via SAE J1939 and the FMS profile, an edge processing layer with navigation positioning via Bluetooth Low Energy, and a cloud platform with a typed binary protocol over TCP/IP and a column-oriented storage model. For the digital road model construction, a high-precision mapping methodology is used, complemented by correction against the global WorldDEM elevation model via spline interpolation, ensuring a relative accuracy of no worse than 0.4 m at a 2 m route discretization. Environmental factors are systematized and their integration principles into the data architecture and the ITS concept are proposed, including the use of V2X channels to transition from a static digital route model to adaptive real-time decision synthesis. Practical validation in a field experiment with a KAMAZ-54901-92 long-haul truck on the R-22 «Kaspiy» route (408 km) confirmed the operability of the proposed solutions, allowing them to be considered as a standalone telematics module for integration into fleet operator platforms and driver decision support systems.

  • Open Access

    Hardware-software system for autonomous tractor control with obstacle avoidance capabilities

    by Sergey Shadrin, Шадрин Сергей Сергеевич, Andrey Keller, Келлер Андрей Владимирович, Daria Makarova, Макарова Дарья Алексеевна, Yuri Furletov, Фурлетов Юрий Михайлович

    BACKGROUND: The development of reliable autonomous agricultural machines requires a comprehensive solution to the problems of navigation, perception of the environment and real-time control. Despite the existing products, the issues of development of a unified hardware-software system that ensures motion and obstacles avoidance in real conditions remain relevant. The aim of the study is to develop such a system for an unmanned tractor. AIM: Development and testing of the hardware-software system for autonomous tractor control that ensures motion along a given path with high accuracy, an all-round view of the environment, distinguishing static and dynamic obstacles, and performing a detour or emergency stop maneuver in accordance with the selected operating mode. METHODS: During the study, a modular software architecture, implemented on an NVIDIA microcomputer, was developed. The hardware package includes a GNSS receiver with RTK correction support (Global Navigation Satellite System with Real-Time Kinematic correction), a computer vision system (4 all-round cameras and a radar), an operator’s tablet console and a wireless communication system. Computer vision algorithms for detecting and distinguishing obstacles, path control algorithms based on the GNSS RTK positional data, and a finite state machine for controlling the operating modes of the system were used for data processing. The functionality was tested with virtual simulation methods. RESULTS: As a result of the development, the hardware-software system that meets all the technical requirements was created. The hardware architecture is specified. The software is implemented as a set of interconnected modules responsible for navigation, motion control, computer vision and operator interface. The developed web interface allows the operator to set routes, select operating modes (“stop” or “detour”) and monitor the system status in real time. Integration tests have confirmed the system’s operability and fault tolerance. CONCLUSION: The hardware-software system that demonstrated the ability to make the tractor move autonomously along a given path and to avoid obstacles during virtual tests has been developed. The key advantages of the solution are modularity and scalability.

  • Open Access

    Detection of increased fuel consumption in vehicles using deep learning in telematics data analysis

    by Artem S. Dubrovskii, Sergey S. Shadrin, Andrey V. Keller, Daria A. Makarova, Yuriy M. Furletov

    BACKGROUND: Despite the widespread use of telematics data from vehicles to monitor fuel efficiency, existing approaches are mainly focused on after-the-fact analysis and do not ensure early detection of persistent operational deviations in real route conditions. Methods that make it possible to interpretably assess changes in operational power and energy losses in real time, taking into account terrain and traffic conditions, have not been sufficiently studied, which necessitates the development of approaches to the early diagnosis of such deviations. AIM: Development of the method for identifying the causes of increased fuel consumption and formulation of diagnostic recommendations for vehicles in real-world operating conditions and its verification. METHODS: 1) Regression-based identification of reference operational indicators obtained from synchronized CAN, GPS, and digital terrain model data. 2) Training of a gradient boosting regression model for fast prediction of these indicators during subsequent trips. 3) Deviation detection via statistical thresholds with persistence requirement, producing interpretable diagnostic conclusions (chassis, aerodynamics, drivetrain) under route context. RESULTS: A stable correspondence between telematics features and operational indicators was obtained, enabling high-accuracy, low-latency monitoring of their drift. On comparable routes, it is shown that hidden malfunctions caused increased fuel consumption relative to the nominal level, which returned to the baseline after targeted maintenance. The novelty lies in integrating a physically meaningful identification stage with machine learning for fast monitoring and interpretable real-time diagnostics. CONCLUSION: The method of detection of increased fuel consumption ensuring fast diagnostics and decrease of actual consumption without noticeable time losses at the given area is developed and verified experimentally. The method operates with standard telematics without additional sensors, runs on embedded computers, and integrates with corporate maintenance systems. It enables early prevention of defect progression and reduces fuel and maintenance costs. Typical operational scenarios demonstrate fuel savings after eliminating overconsumption causes. The method is relevant for heavy-duty and agricultural machinery.

  • Open Access

    Development and Field Testing of an Acoustic Sensor Unit for Smart Crossroads as Part of V2X Infrastructure

    by Yury Furletov, Dinara Aptinova, Mekan Mededov, Andrey Keller, Sergey S. Shadrin, Daria A. Makarova

    Improving city crossroads safety is a critical problem for modern smart transportation systems (STS). This article presents the results of developing, upgrading, and comprehensively experimentally testing an acoustic monitoring system prototype designed for rapid accident detection. Unlike conventional camera- or lidar-based approaches, the proposed solution uses passive sound source localization to operate effectively with no direct visibility and in adverse weather conditions, addressing a key limitation of camera- or lidar-based systems. Generalized Cross-Correlation with Phase Transform (GCC-PHAT) algorithms were used to develop a hardware–software complex featuring four microphones, a multichannel audio interface, and a computation module. This study focuses on the gradual upgrading of the algorithm to reduce the mean localization error in real-life urban conditions. Laboratory and complex field tests were conducted on an open-air testing ground of a university campus. During these tests, the system demonstrated that it can accurately determine the coordinates of a sound source imitating accidents (sirens, collisions). The analysis confirmed that the system satisfies the V2X infrastructure integration response time requirement (<200 ms). The results suggest that the system can be used as part of smart transportation systems.


  • Open Access

    Experimental Investigation and Performance Evaluation of Automated Emergency Braking (AEB) Systems Under Actual Driving Conditions

    by Viktor V. Petin, Andrey V. Keller, Sergey S. Shadrin, Daria A. Makarova, Yury M. Furletov

    This paper presents an experimental study of the Automatic Emergency Braking (AEB) system, focusing on three essential testing phases: verifying the match between calculated and actual brake actuator operation time, validating the forecasted vs. real-time stabilized deceleration onset duration, and comparing the theoretically computed braking distance derived from mathematical models with its actual measurement. Standard instrumentation coupled with an original test procedure was utilized during the experiments. A full-scale experimental campaign was conducted on a specialized proving ground, thus substantiating the validity and robustness of the computational models used for assessing the AEB system parameters. The empirical outcomes confirmed that current-generation AEB systems offer dependable predictions regarding braking dynamics and exhibit prompt responsiveness to imminent collisions. However, it should be noted that variations in road conditions, driver behavior, and sensor precision may affect their performance. Consequently, additional efforts aimed at optimizing existing AEB solutions are required to minimize potential errors and enhance overall reliability. Finally, the significance of complying with design specifications and continuously upgrading AEB systems to meet evolving road safety standards is emphasized.


  • Open Access

    Anti-Slip Control System with Self-Oscillation Suppression Function for the Electromechanical Drive of Wheeled Vehicles

    by Aleksandr V. Klimov, Akop V. Antonyan, Andrey V. Keller, Sergey S. Shadrin, Daria A. Makarova, Yury M. Furletov

    The movement of a wheeled vehicle is a non-regular dynamic process characterized by a large number of states that depend on the movement conditions. This movement involves a large number of situations where elastic tires skid and slip against the base surface. This reduces the efficiency of movement as useful mechanical energy of the electromechanical drive is spent to overcome the increased skidding and slipping. Complete sliding results in the loss of control over the vehicle, which is unsafe. Processes that take place immediately before such phenomena are of special interest as their parameters can be useful in diagnostics and control. Additionally, such situations involve adverse oscillatory processes that cause additional dynamic mechanical and electrical loading in the electromechanical drive that can result in its failure. The authors provide the results of laboratory road research into the emergence of self-oscillatory phenomena during the rolling of a wheel with increased skidding on the base surface and a low traction factor. This paper reviews the methods of designing an anti-slip control system for wheels with an oscillation damping function and studies the applicability and efficiency of the suggested method using mathematical simulation of the virtual vehicle operation in the Matlab Simulink software package. Using the self-oscillation suppression algorithm in the control system helps reduce the maximum amplitude values by 5 times and average amplitudes by 2.5 times while preventing the moment operator from changing. The maximum values of current oscillation amplitude during algorithm changes were reduced by 2.5 times, while the current change rate was reduced by 3 times. The reduction in the current-change amplitude and rate proves the efficiency of the self-oscillation suppression algorithm. The high change rate of the current consumed by the drive’s inverters may have a negative impact on the remaining operating life of the rechargeable electric power storage system. This impact increases with the proximity of its location due to the low inductance of the connecting lines and the operating parameters, and the useful life of the components of the autonomous voltage inverters.


  • Open Access

    Developing an Algorithm Limiting the Longitudinal Acceleration of an Electric Vehicle

    by Akop Antonyan, Aleksandr Klimov, Andrey Buchkin, Andrey Keller, Sergey Shadrin, Daria Makarova, Yury Furletov

    The electric traction drive is increasingly being applied as a device providing traction force on driving wheels. This is due to its reliable torque transmission to the driving wheels, step-less regulation of the traction force on the driving wheels depending on the driving conditions, and increased design capabilities. In terms of power, the electric traction drive has maximum torque at low speeds, which internal combustion engines lack. This property of the electric drive is not applied in urban vehicles, as not all passengers are comfortable with intensive acceleration. In modern vehicles with an electric traction drive, the maximum acceleration can be limited by software, which is the focus of this study. This paper aims to develop an algorithm capable of recognizing when the permissible longitudinal acceleration exceeds the limit and generating an action to maintain the acceptable acceleration level. The electric traction drive of a large-class electric bus was used as a control object. An algorithm and a control law are hereby developed, which reduce longitudinal acceleration using PI control. Both simulation modeling and full-scale tests on the electric bus were carried out to evaluate the performance and efficiency of the algorithm. In this paper, the authors also introduce the cumulative velocity concept and prove the operability and efficiency of the developed method.