Frédéric Georgi
Frédéric Georgi has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Hélène Rotella
Université Côte d’Azur, CNRS, CRHEA, rue Bernard Grégory, 06560 Valbonne, France
3 shared publications - Maxime Hugues
Université Côte d'Azur, CNRS, CRHEA, rue Bernard Grégory , Valbonne 06560
3 shared publications - Yvon Cordier
Université Côte d'Azur, CNRS, CRHEA 4 , rue Bernard Grégory, 06560 Valbonne
3 shared publications - Adam Nassif2 shared publications
- Caroline Elias
University Côte d’Azur, CNRS, CRHEA 1 , rue B. Gregory, 06560 Valbonne, France
2 shared publications - Ileana Florea
Université Côte d'Azur
2 shared publications
Latest Publications
- 16 June 2026
- Published by American Physical Society (APS) in Physical Review Materials
- Vol. 10 (6)
Stabilization of epitaxial ZnMgN through oxygen incorporation: Properties of quaternary ZnMgNO
- 16 June 2026
- Published by American Physical Society (APS) in Physical Review Materials
- Vol. 10 (6)
Stabilization of epitaxial ZnMgN through oxygen incorporation: Properties of quaternary ZnMgNO
- Open Access
- 23 December 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 138 (24)
Surface oxidation and oxygen incorporation in ScAlN films grown by molecular beam epitaxy
Recently, there has been much interest in the ScAlN alloy, thanks to its various potential applications in high-frequency high-power, acoustoelectric, and ferroelectric devices. Nonetheless, these applications could be impaired by the presence of oxygen in the alloy and the formation of a surface oxide layer due to the high affinity of scandium with such impurity. A current trend is to increase the Sc content and most of the time it is accompanied by a lowering of the growth temperature. As it probably strongly influences the incorporation of impurities, we have carefully studied the effects of growth temperature and Sc content in the surface oxide and oxygen content of ScAlN films grown by ammonia source molecular beam epitaxy. The oxygen concentration and bonding configuration have been determined by combining normal-incidence, angle resolved, and ion-etching x-ray photoelectron spectroscopy.
- 23 December 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 138 (24)
Open AccessSurface oxidation and oxygen incorporation in ScAlN films grown by molecular beam epitaxy
Recently, there has been much interest in the ScAlN alloy, thanks to its various potential applications in high-frequency high-power, acoustoelectric, and ferroelectric devices. Nonetheless, these applications could be impaired by the presence of oxygen in the alloy and the formation of a surface oxide layer due to the high affinity of scandium with such impurity. A current trend is to increase the Sc content and most of the time it is accompanied by a lowering of the growth temperature. As it probably strongly influences the incorporation of impurities, we have carefully studied the effects of growth temperature and Sc content in the surface oxide and oxygen content of ScAlN films grown by ammonia source molecular beam epitaxy. The oxygen concentration and bonding configuration have been determined by combining normal-incidence, angle resolved, and ion-etching x-ray photoelectron spectroscopy.
- 9 May 2025
- Published by Elsevier in Tribology International
- Vol. 210
Synergistic anti-wear performance of TiO2 nanoparticles and ZDDP: Influence of dispersion methods
- 9 May 2025
- Published by Elsevier in Tribology International
- Vol. 210
Synergistic anti-wear performance of TiO2 nanoparticles and ZDDP: Influence of dispersion methods
- 1 May 2025
- Published by Elsevier in Tribology International
- Vol. 209
Electric polarity: A key factor in lubricated wear of bearing steel
- 1 May 2025
- Published by Elsevier in Tribology International
- Vol. 209
Electric polarity: A key factor in lubricated wear of bearing steel
- 1 March 2024
- Published by AIP Publishing in APL Materials
- Vol. 12 (3)
Erratum: “Influence of the temperature on growth by ammonia source molecular beam epitaxy of wurtzite phase ScAlN alloy on GaN” [APL Mater. 11, 031105 (2023)]
An error has been identified in the primary axis label of Fig. 4(a) of the original paper:1 the unit of capacitance should be mF/m2 rather than F/cm2. The corre
- 1 March 2024
- Published by AIP Publishing in APL Materials
- Vol. 12 (3)
Erratum: “Influence of the temperature on growth by ammonia source molecular beam epitaxy of wurtzite phase ScAlN alloy on GaN” [APL Mater. 11, 031105 (2023)]
An error has been identified in the primary axis label of Fig. 4(a) of the original paper:1 the unit of capacitance should be mF/m2 rather than F/cm2. The corre
- Open Access
- 16 October 2023
- Published by AIP Publishing in Applied Physics Letters
- Vol. 123 (16)
Alloy distribution and compositional metrology of epitaxial ScAlN by atom probe tomography
The properties of ScAlN layers grown by molecular beam epitaxy have been carefully studied using atom probe tomography (APT) and complementary techniques. The measured III-site fraction within the ScxAl1−xN layer is x = 0.16 ± 0.02, in good agreement with the values determined by x-ray photoelectron spectroscopy (XPS, x = 0.14) and secondary ion mass spectrometry (SIMS, x = 0.14). The frequency distribution analysis indicates that the compound behaves as a random alloy. A significant amount of oxygen, around 0.2% in site fraction, is found within the ScAlN layer as a randomly distributed impurity. The alloy composition measurement in terms of Sc fraction is rather independent of the surface electric field, which excludes compositional inaccuracies for the experimental parameters used in the APT analysis.
- 16 October 2023
- Published by AIP Publishing in Applied Physics Letters
- Vol. 123 (16)
Open AccessAlloy distribution and compositional metrology of epitaxial ScAlN by atom probe tomography
The properties of ScAlN layers grown by molecular beam epitaxy have been carefully studied using atom probe tomography (APT) and complementary techniques. The measured III-site fraction within the ScxAl1−xN layer is x = 0.16 ± 0.02, in good agreement with the values determined by x-ray photoelectron spectroscopy (XPS, x = 0.14) and secondary ion mass spectrometry (SIMS, x = 0.14). The frequency distribution analysis indicates that the compound behaves as a random alloy. A significant amount of oxygen, around 0.2% in site fraction, is found within the ScAlN layer as a randomly distributed impurity. The alloy composition measurement in terms of Sc fraction is rather independent of the surface electric field, which excludes compositional inaccuracies for the experimental parameters used in the APT analysis.