Zainab Bibi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Zainab Bibi has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Sidra Chaudhary
Department of Applied Chemistry, School of Chemistry, Xi’an Jiaotong University, No. 28, Xianning West Road, Xi’an 710049, China
5 shared publications - Xiaoyong Li
Department of Applied Chemistry, School of Chemistry, Xi’an Jiaotong University, No. 28, Xianning West Road, Xi’an 710049, China
5 shared publications - Yang Sun
Department of Applied Chemistry, School of Chemistry, Xi’an Jiaotong University, No. 28, Xianning West Road, Xi’an 710049, China
5 shared publications - Qin-Xiang Jia
Department of Applied Chemistry, School of Chemistry, Xi’an Jiaotong University, No. 28, Xianning West Road, Xi’an 710049, China
4 shared publications - Yong Wu
Department of Applied Chemistry, School of Chemistry, Xi’an Jiaotong University, No. 28, Xianning West Road, Xi’an 710049, China
4 shared publications - Zhiyuan Song
Department of Applied Chemistry, School of Chemistry, Xi’an Jiaotong University, No. 28, Xianning West Road, Xi’an 710049, China
3 shared publications
Latest Publications
- Open Access
- 13 February 2025
- Published by MDPI AG in Nanomaterials
- Vol. 15 (4) , 283
The Encapsulation of Illite Powders with Al2(SO4)3·18H2O and Hydrophilic Copolymers: Accelerating and Toughening Cement Hydration Through the Proliferation of 54CaO·MgO·Al2O3·16SiO2 Clinker
Two hydrophilic copolymers containing functional groups such as carboxyl, amido, and sulfonic acid are synthesized using ammonium persulfate-catalyzed free radical polymerization in water. Aluminum sulfate is then introduced, resulting in two polymer complexes that exhibit reduced cement setting times (initial, 1.16–2.44 min; final, 2.02–3.14 min) and improved compressive (24 h, 5.81–7.25 MPa) and flexural (24 h, 2.80–2.99 MPa) strengths compared to pure aluminum sulfate-facilitated cementing (initial, 19.11 min; final, 37.05 min; compressive, 24 h, 5.51 MPa; flexural, 24 h, 2.56 MPa). Following this, ball-milled illite powder is added, and the resulting admixtures further display slightly prolonged setting times (initial, 2.35–2.99 vs. 1.16–2.44 min; final, 3.98–4.35 vs. 2.02–3.14 min), along with comparable compressive strengths (5.85–7.11 vs. 5.81–7.25 MPa) and enhanced flexural strengths (3.92–5.83 vs. 2.80–2.99 MPa). Notably, a unique adhesive pozzolanic clinker, Ca54MgAl2Si16O90 (54CaO·MgO·Al2O3·16SiO2), emerges in the presence of illite-based admixtures, contributing to the mechanical strength development of the hydrated mortars. Although illite itself is hydrophobic, the coating of ball-milled illite powder with aluminum sulfate and copolymers facilitates its dispersion into the gaps and pores of the cement matrix during setting, thereby increasing the flexural strength. This work presents an interesting approach to utilizing illite materials in cement applications, which is significant for reducing CO2 emissions during cement production and use.
- 13 February 2025
- Published by MDPI AG in Nanomaterials
- Vol. 15 (4) , 283
Open AccessThe Encapsulation of Illite Powders with Al2(SO4)3·18H2O and Hydrophilic Copolymers: Accelerating and Toughening Cement Hydration Through the Proliferation of 54CaO·MgO·Al2O3·16SiO2 Clinker
Two hydrophilic copolymers containing functional groups such as carboxyl, amido, and sulfonic acid are synthesized using ammonium persulfate-catalyzed free radical polymerization in water. Aluminum sulfate is then introduced, resulting in two polymer complexes that exhibit reduced cement setting times (initial, 1.16–2.44 min; final, 2.02–3.14 min) and improved compressive (24 h, 5.81–7.25 MPa) and flexural (24 h, 2.80–2.99 MPa) strengths compared to pure aluminum sulfate-facilitated cementing (initial, 19.11 min; final, 37.05 min; compressive, 24 h, 5.51 MPa; flexural, 24 h, 2.56 MPa). Following this, ball-milled illite powder is added, and the resulting admixtures further display slightly prolonged setting times (initial, 2.35–2.99 vs. 1.16–2.44 min; final, 3.98–4.35 vs. 2.02–3.14 min), along with comparable compressive strengths (5.85–7.11 vs. 5.81–7.25 MPa) and enhanced flexural strengths (3.92–5.83 vs. 2.80–2.99 MPa). Notably, a unique adhesive pozzolanic clinker, Ca54MgAl2Si16O90 (54CaO·MgO·Al2O3·16SiO2), emerges in the presence of illite-based admixtures, contributing to the mechanical strength development of the hydrated mortars. Although illite itself is hydrophobic, the coating of ball-milled illite powder with aluminum sulfate and copolymers facilitates its dispersion into the gaps and pores of the cement matrix during setting, thereby increasing the flexural strength. This work presents an interesting approach to utilizing illite materials in cement applications, which is significant for reducing CO2 emissions during cement production and use.
- Open Access
The Efficient and Environmentally Friendly Chlorination of Arene, Alcohol, Halobenzene, and Peroxide Catalyzed by Fe–Ba Binary Oxides Using Hydrochloric Acid as Chlorine Source and Aqueous H2O2 as Oxidant
A series of Fe–Ba mixed oxides, including a pure Fe-containing sample as a reference, have been synthesized via a sol–gel process using Fe3+ or Fe2+ salts and BaSO4 as raw materials, with Pluronic P123 serving as a template. These oxides have been thoroughly characterized and subsequently utilized as catalysts for the chlorination of various organic molecules. Commercial hydrochloric acid, known for its relative safety, and environmentally friendly aqueous hydrogen peroxide were employed as the chlorine source and oxidant, respectively. The pure Fe-containing catalyst displays excellent thermal stability between 600 and 800 °C and exhibited moderate to high conversions in the chlorination of toluene, benzene, and tert-butyl hydroperoxide, with remarkable ortho-selectivity in chlorination of toluene. The combination of Fe3+ salt with BaSO4 in the sol–gel process results in a Fe–Ba mixed oxide catalyst composed of BaO2, BaFe4O7, and Fe2O3, significantly enhancing the chlorination activity compared to that displayed by the pure Fe catalyst. Notably, the chlorination of tert-butyl hydroperoxide (TBHP) does not require additional oxidants such as H2O2, and involves both electrophilic substitution and nucleophilic addition. Notably, the chlorination of bromobenzene yields chlorobenzene as the sole product, a transformation that has not been previously reported. Overall, this catalytic chlorination system holds promise for advancing the chlorination industry and enhancing pharmaceutical production.
Open AccessThe Efficient and Environmentally Friendly Chlorination of Arene, Alcohol, Halobenzene, and Peroxide Catalyzed by Fe–Ba Binary Oxides Using Hydrochloric Acid as Chlorine Source and Aqueous H2O2 as Oxidant
A series of Fe–Ba mixed oxides, including a pure Fe-containing sample as a reference, have been synthesized via a sol–gel process using Fe3+ or Fe2+ salts and BaSO4 as raw materials, with Pluronic P123 serving as a template. These oxides have been thoroughly characterized and subsequently utilized as catalysts for the chlorination of various organic molecules. Commercial hydrochloric acid, known for its relative safety, and environmentally friendly aqueous hydrogen peroxide were employed as the chlorine source and oxidant, respectively. The pure Fe-containing catalyst displays excellent thermal stability between 600 and 800 °C and exhibited moderate to high conversions in the chlorination of toluene, benzene, and tert-butyl hydroperoxide, with remarkable ortho-selectivity in chlorination of toluene. The combination of Fe3+ salt with BaSO4 in the sol–gel process results in a Fe–Ba mixed oxide catalyst composed of BaO2, BaFe4O7, and Fe2O3, significantly enhancing the chlorination activity compared to that displayed by the pure Fe catalyst. Notably, the chlorination of tert-butyl hydroperoxide (TBHP) does not require additional oxidants such as H2O2, and involves both electrophilic substitution and nucleophilic addition. Notably, the chlorination of bromobenzene yields chlorobenzene as the sole product, a transformation that has not been previously reported. Overall, this catalytic chlorination system holds promise for advancing the chlorination industry and enhancing pharmaceutical production.
- Open Access
Al(SO4)(OH)·5H2O Stemming from Complexation of Aluminum Sulfate with Water-Soluble Ternary Copolymer and further Stabilized by Silica Gel as Effective Admixtures for Enhanced Mortar Cementing
A water-soluble ternary copolymer bearing carboxyl, sulfonic, and amide functional groups was synthesized using ammonium persulfate-catalyzed free radical polymerization in water, resulting in high monomer conversion. This copolymer was then complexed with aluminum sulfate, forming an admixture containing Al(SO4)(OH)·5H2O, which was subsequently combined with silica gel. Characterization revealed that the synthesized copolymer formed a large, thin membrane that covered both the aluminum compounds and the silica gel blocks. The introduction of this complex admixture, combining the copolymer and aluminum sulfate, not only reduced the setting times of the cement paste but also enhanced the mechanical strengths of the mortar compared to using aluminum sulfate alone. The complex admixture led to the formation of katoite, metajennite, and C3A (tricalcium aluminate) in the mortar, demonstrating significant linking effects, whereas pure aluminum sulfate could not completely transform C3S within 24 h. Further addition of silica gel to the complex admixture further shortened the setting times of the paste, slightly reduced compressive strength, but improved flexural strength compared to the initial complex admixture. The silicon components appeared to fill the micropores and mesopores of the mortar, accelerating cement setting and enhancing flexural strength, while slightly decreasing compressive strength. This study contributed to the development of new cementing accelerators with improved hardening properties.
Open AccessAl(SO4)(OH)·5H2O Stemming from Complexation of Aluminum Sulfate with Water-Soluble Ternary Copolymer and further Stabilized by Silica Gel as Effective Admixtures for Enhanced Mortar Cementing
A water-soluble ternary copolymer bearing carboxyl, sulfonic, and amide functional groups was synthesized using ammonium persulfate-catalyzed free radical polymerization in water, resulting in high monomer conversion. This copolymer was then complexed with aluminum sulfate, forming an admixture containing Al(SO4)(OH)·5H2O, which was subsequently combined with silica gel. Characterization revealed that the synthesized copolymer formed a large, thin membrane that covered both the aluminum compounds and the silica gel blocks. The introduction of this complex admixture, combining the copolymer and aluminum sulfate, not only reduced the setting times of the cement paste but also enhanced the mechanical strengths of the mortar compared to using aluminum sulfate alone. The complex admixture led to the formation of katoite, metajennite, and C3A (tricalcium aluminate) in the mortar, demonstrating significant linking effects, whereas pure aluminum sulfate could not completely transform C3S within 24 h. Further addition of silica gel to the complex admixture further shortened the setting times of the paste, slightly reduced compressive strength, but improved flexural strength compared to the initial complex admixture. The silicon components appeared to fill the micropores and mesopores of the mortar, accelerating cement setting and enhancing flexural strength, while slightly decreasing compressive strength. This study contributed to the development of new cementing accelerators with improved hardening properties.
- Open Access
The Coordination of Aluminum Sulfate with a Water-Soluble Block Copolymer Containing Carboxyl, Amide, Sulfonic and Anhydride Groups Providing Both Accelerating and Hardening Effects in Cement Setting
Two water-soluble block copolymers composed of acrylic acid (AA), 2-acrylamido-2-methylpropane sulfonic acid (AMPS), and optionally maleic anhydride (MAH) were synthesized through ammonium persulfate-catalyzed free radical polymerization in water. The introduction of aluminum sulfate (AS) into the resulting mixtures significantly reduced the setting times of the paste and enhanced the mechanical strength of the mortar compared to both the additive-free control and experiments facilitated solely by pure AS. This improvement was primarily attributed to the inhibition of rapid Al3+ hydrolysis, which was achieved through coordination of the synthesized block copolymers, along with the formation of newly identified hydrolytic intermediates. Notably, the ternary copolymer (AA–AMPS–MAH) exhibited superior performance compared to that of the binary copolymer (AA–AMPS). In the early stages of cement setting, clusters of ettringite (AFt) were found to be immobilized over newly detected linkage phases, including unusual calcium silicate hydrate and epistilbite. In contrast to the well-documented role of polymers in retarding cement hydration, this study presents a novel approach by providing both accelerating and hardening agents for cement setting, which has significant implications for the future design of cement additives.
Open AccessThe Coordination of Aluminum Sulfate with a Water-Soluble Block Copolymer Containing Carboxyl, Amide, Sulfonic and Anhydride Groups Providing Both Accelerating and Hardening Effects in Cement Setting
Two water-soluble block copolymers composed of acrylic acid (AA), 2-acrylamido-2-methylpropane sulfonic acid (AMPS), and optionally maleic anhydride (MAH) were synthesized through ammonium persulfate-catalyzed free radical polymerization in water. The introduction of aluminum sulfate (AS) into the resulting mixtures significantly reduced the setting times of the paste and enhanced the mechanical strength of the mortar compared to both the additive-free control and experiments facilitated solely by pure AS. This improvement was primarily attributed to the inhibition of rapid Al3+ hydrolysis, which was achieved through coordination of the synthesized block copolymers, along with the formation of newly identified hydrolytic intermediates. Notably, the ternary copolymer (AA–AMPS–MAH) exhibited superior performance compared to that of the binary copolymer (AA–AMPS). In the early stages of cement setting, clusters of ettringite (AFt) were found to be immobilized over newly detected linkage phases, including unusual calcium silicate hydrate and epistilbite. In contrast to the well-documented role of polymers in retarding cement hydration, this study presents a novel approach by providing both accelerating and hardening agents for cement setting, which has significant implications for the future design of cement additives.
- Open Access
Mechanochemical Synthesis of PdO2 Nanoparticles Immobilized over Silica Gel for Catalytic Suzuki–Miyaura Cross-Coupling Reactions Leading to the C-3 Modification of 1H-Indazole with Phenylboronic Acids
The C-3 modification of 1H-indazole has produced active pharmaceuticals for the treatment of cancer and HIV. But, so far, this transformation has seemed less available, due to the lack of efficient C-C bond formation at the less reactive C-3 position. In this work, a series of silica gel-supported PdO2 nanoparticles of 25–66 nm size were prepared by ball milling silica gel with divalent palladium precursors, and then employed as catalysts for the Suzuki–Miyaura cross-coupling of 1H-indazole derivative with phenylboronic acid. All the synthesized catalysts showed much higher cross-coupling yields than their palladium precursors, and could also be reused three times without losing high activity and selectivity in a toluene/water/ethanol mixed solvent. Although the palladium precursors showed an order of activity of PdCl2(dppf, 1,1′-bis(diphenylphosphino)ferrocene) > PdCl2(dtbpf, 1,1′-bis(di-tert-butylphosphino)ferrocene) > Pd(OAc, acetate)2, the synthesized catalysts showed an order of C1 (from Pd(OAc)2) > C3 (from PdCl2(dtbpf)) > C2 (from PdCl2(dppf)), which conformed to the orders of BET (Brunauer–Emmett–Teller) surface areas and acidities of these catalysts. Notably, the most inexpensive Pd(OAc)2 can be used as a palladium precursor for the synthesis of the best catalyst through simple ball milling. This work provides a highly active and inexpensive series of catalysts for C-3 modification of 1H-indazole, which are significant for the large-scale production of 1H-indazole-based pharmaceuticals.
Open AccessMechanochemical Synthesis of PdO2 Nanoparticles Immobilized over Silica Gel for Catalytic Suzuki–Miyaura Cross-Coupling Reactions Leading to the C-3 Modification of 1H-Indazole with Phenylboronic Acids
The C-3 modification of 1H-indazole has produced active pharmaceuticals for the treatment of cancer and HIV. But, so far, this transformation has seemed less available, due to the lack of efficient C-C bond formation at the less reactive C-3 position. In this work, a series of silica gel-supported PdO2 nanoparticles of 25–66 nm size were prepared by ball milling silica gel with divalent palladium precursors, and then employed as catalysts for the Suzuki–Miyaura cross-coupling of 1H-indazole derivative with phenylboronic acid. All the synthesized catalysts showed much higher cross-coupling yields than their palladium precursors, and could also be reused three times without losing high activity and selectivity in a toluene/water/ethanol mixed solvent. Although the palladium precursors showed an order of activity of PdCl2(dppf, 1,1′-bis(diphenylphosphino)ferrocene) > PdCl2(dtbpf, 1,1′-bis(di-tert-butylphosphino)ferrocene) > Pd(OAc, acetate)2, the synthesized catalysts showed an order of C1 (from Pd(OAc)2) > C3 (from PdCl2(dtbpf)) > C2 (from PdCl2(dppf)), which conformed to the orders of BET (Brunauer–Emmett–Teller) surface areas and acidities of these catalysts. Notably, the most inexpensive Pd(OAc)2 can be used as a palladium precursor for the synthesis of the best catalyst through simple ball milling. This work provides a highly active and inexpensive series of catalysts for C-3 modification of 1H-indazole, which are significant for the large-scale production of 1H-indazole-based pharmaceuticals.