Sayop Kim
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Sayop Kim has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Je Ir Ryu
Division of Engineering, New York University Abu Dhabi 1 , Abu Dhabi, United Arab Emirates
3 shared publications - Chol-Bum Mike Kweon
DEVCOM Army Research Laboratory, Aberdeen, MD, USA
2 shared publications Kenneth S. Kim
2 shared publications- Roberto Torelli
Argonne National Laboratory, Lemont, IL, USA
1 shared publication Surya Kaundinya Oruganti
Transportation and Power Systems Division, Argonne National Laboratory 2 , Lemont, Illinois 60439, USA
1 shared publicationTonghun Lee
Department of Mechanical Science and Engineering, University of Illinois at Urbana-Champaign 4 , Urbana, Illinois 61801, USA
1 shared publication
Latest Publications
- 26 September 2026
- Published by Elsevier in Proceedings of the Combustion Institute
- Vol. 42
Understanding detonation propagation modes through energy distribution in rotating detonation engines
- 26 September 2026
- Published by Elsevier in Proceedings of the Combustion Institute
- Vol. 42
Understanding detonation propagation modes through energy distribution in rotating detonation engines
- 4 October 2024
- Published by Elsevier in Combustion and Flame
- Vol. 270
Physiochemical View of Fuel Jet Impingement and Ignition Upon Contact with a Cylindrical Hot Surface
- 4 October 2024
- Published by Elsevier in Combustion and Flame
- Vol. 270
Physiochemical View of Fuel Jet Impingement and Ignition Upon Contact with a Cylindrical Hot Surface
- Open Access
- 1 October 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (10)
Modeling of the spray-induced wall stress acting on the ignition assistance device
This research introduces a novel wall-stress model called the Spray-Induced Wall Stress (SIWS) model, which considers the effects of spray-wall impingement and the resulting formation of wall stress within the Lagrangian spray modeling framework. The primary objective of this paper is to provide a mathematical description of the fundamental physics underlying the model. Subsequently, the proposed model is validated using existing experimental data. The remainder of the study focuses on the practical application of the model to an ignition assistance device. Specifically, this device is installed in a compression ignition engine and designed to enhance ignition in aviation-fueled high-altitude aircraft propulsion systems. The research sheds light on the mechanical impulse caused by the high-speed impact of the spray jet, leading to the accumulation of mechanical stress on the rigid body of the ignition assistance device. Previous studies on fluid–structure interaction have only considered the interaction between the gas phase and the solid wall. However, the SIWS model incorporates the additional impact of the impinging liquid spray jet. Consequently, the simulated stress distribution on the ignition assistance device can be estimated by considering both the gas-phase-induced term and the spray-induced term simultaneously.
- 1 October 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (10)
Open AccessModeling of the spray-induced wall stress acting on the ignition assistance device
This research introduces a novel wall-stress model called the Spray-Induced Wall Stress (SIWS) model, which considers the effects of spray-wall impingement and the resulting formation of wall stress within the Lagrangian spray modeling framework. The primary objective of this paper is to provide a mathematical description of the fundamental physics underlying the model. Subsequently, the proposed model is validated using existing experimental data. The remainder of the study focuses on the practical application of the model to an ignition assistance device. Specifically, this device is installed in a compression ignition engine and designed to enhance ignition in aviation-fueled high-altitude aircraft propulsion systems. The research sheds light on the mechanical impulse caused by the high-speed impact of the spray jet, leading to the accumulation of mechanical stress on the rigid body of the ignition assistance device. Previous studies on fluid–structure interaction have only considered the interaction between the gas phase and the solid wall. However, the SIWS model incorporates the additional impact of the impinging liquid spray jet. Consequently, the simulated stress distribution on the ignition assistance device can be estimated by considering both the gas-phase-induced term and the spray-induced term simultaneously.