Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Hooman Mehdizadeh-Rad has a total of 35 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Time-resolved advanced exergy analysis of a field-validated solar–hydrogen microgrid with anion-exchange-membrane electrolysis and detailed balance-of-plant modelling

    by Hooman Mehdizadeh-Rad, Luis F. Herrera Diaz, Maurizio Cirrincione, Djafar Chabane, Ali Mohammadi, Mojtaba Abdi-Jalebi, Suresh Thennadil

  • Open Access

    A New Approach to Study Stability in a Lead‐Free Perovskite Cs 4 CuSb 2 Cl 12 ‐Based Solar Cell

    by Junbo Jia, Daniel Dodzi Yao Setsoafia, David Ompong, Hooman Mehdizadeh Rad, Kiran Sreedhar Ram, Jai Singh

    We have simulated a solar cell of lead‐free inorganic perovskite Cs 4 CuSb 2 Cl 12 of the optimized structure, FTO/WS 2 /Cs 4 CuSb 2 Cl 12 /P 3 HT/Co, which is expected to be more stable compared with solar cells containing halide perovskite. First, a few different anode, electron transport layer, and hole transport layer materials are tried, and then the above best combination is found to give the highest power conversion efficiency. Following that, the thickness of the active layer, the concentration of the defect density in the interfaces of WS 2 /Cs 4 CuSb 2 Cl 12 and Cs 4 CuSb 2 Cl 12 /P 3 HT, and in the active layer are optimized. The optimal structure of FTO/WS 2 /Cs 4 CuSb 2 Cl 12 /P 3 HT/Co thus determined reveals J SC = 23.64 mA/cm 2 , V OC = 1.44 V, FF = 84.87% and PCE = 28.97%. We have also assessed the stability of this PSC by reducing the number of interfaces, which are apparently responsible for degradation. The above PSC without both HTL and ETL reveals a lower PCE of 18.9% but may be considered more stable, and the PSC without the ETL gives a PCE of 29.3% because this structure supports better charge carrier transport. As the active layer of this PSC is inorganic, it is expected to be more stable.

  • Open Access

    Two‐Photon Absorption in Perovskite Semiconductors

    by David Ompong, Michael Edem Donkor, Emmanuel Ofosu, Daniel Dodzi Yao Setsoafia, Hooman Mehdizadeh‐Rad, Kiran Sreedhar Ram, Jai Singh

    Perovskite semiconductors have emerged as promising materials for nonlinear photonic, optoelectronic, and energy‐conversion applications, yet a predictive theory of two‐photon absorption (TPA) in these materials remains incomplete. The existing TPA models were primarily developed for conventional semiconductors and neglect the unique band‐structure characteristics of perovskites. In this work, we have developed an analytical model for the TPA coefficient, K 2 , in perovskite semiconductors using second‐order perturbation theory within the parabolic‐band framework, including excitonic effects. The model incorporates the inter‐ and intra‐band transitions associated with the heavy‐electron, light‐electron, and spin–orbit split‐off conduction band states. Numerical calculations performed for representative perovskite materials show good agreement between theory and experiment over a wide temperature range, including TPA coefficients at 290 and 50 K. The results highlight the importance of accounting for the band structure, excitonic and relativistic effects when analyzing TPA spectra in perovskite semiconductors and lay the foundation for the design of perovskite‐based nonlinear optical and photonic devices.

  • Open Access

    Density Functional Theory Simulation of Dithienothiophen[3,2-b]-pyrrolobenzothiadiazole-Based Organic Solar Cells

    by Daniel Dodzi Yao Setsoafia, Kiran Sreedhar Ram, Hooman Mehdizadeh-Rad, David Ompong, Jai Singh

    We have simulated the effect of changing the end groups in BTP core with five organic units of 1,3-Indandione (IN), 2-thioxothiazolidin-4-one (Rhodanine), propanedinitrile (Malononitrile), (2-(6-oxo-5,6-dihydro-4H-cyclopenta[c]thiophen-4-ylidene)malononitrile) (CPTCN) and 2-(3-oxo-2,3-dihydroinden-1-ylidene (IC), and two halogenated units of (4F) IC and (4Cl) IC on the optical and photovoltaic properties of the BTP DA’D core molecular unit. Thus modified, seven molecular structures are considered and their optical properties, including HOMO and LUMO energies and absorption spectra are simulated in this paper. On the basis of HOMO and LUMO energies, it is found that two of the seven molecules, BTP-IN and BTP-Rhodanine, can act as donors and the other four, BTP-(4F) IC, BTP-(4Cl) IC, BTP-CPTCN and BTP-IC, as acceptors in designing bulk heterojunction (BHJ) organic solar cells (OSCs). Using these combinations of donors and acceptors in the active layer, eight BHJ OSCs, such as BTP-IN: BTP-(4F) IC, BTP-IN: BTP-(4Cl) IC, BTP-IN: BTP-CPTCN, BTP-IN: BTP-IC, BTP-Rhodanine: BTP-(4F) IC, BTP-Rhodanine: BTP-(4Cl) IC, BTP-Rhodanine: BTP-CPTCN and BTP-Rhodanine: BTP-IC, are designed, and their photovoltaic performance is simulated. The photovoltaic parameters Jsc, Voc and FF for all eight BHJ OSCs and their power conversion efficiency (PCE) are simulated. It is found that the BHJ OSC of the BTP-IN: BTP-CPTCN donor–acceptor blend gives the highest PCE (14.73%) and that of BTP-Rhodanine: BTP-(4F) IC gives the lowest PCE (12.07%). These results offer promising prospects for the fabrication of high-efficiency BHJ OSCs with the blend of both donor and acceptor based on the same core structure.


  • Open Access

    Density Functional Theory Simulation of Optical and Photovoltaic Properties of DRTB-T Donor-Based Organic Solar Cells

    by Daniel Dodzi Yao Setsoafia, Kiran Sreedhar Ram, Hooman Mehdizadeh-Rad, David Ompong, Jai Singh

    Using the density functional theory (DFT), the influence of substitution of electron-donating (OCH3 and OH) and electron-accepting (F and Cl) groups on the peripheral thiophene units of DRTB-T donor molecule is studied. By optimizing the geometric structure, HOMO and LUMO energies, reorganization energies, optical properties, and photovoltaic properties are simulated. It is found that the ionization potential of the electron-donating derivatives (DRTB-4OCH3 and DRTB-4OH) reduces, but it increases for the electron-accepting derivatives (DRTB-4F and DRTB-4Cl) in comparison with that of DRTB-T. It is also found that the absorption spectra of the electron-donating derivatives (DRTB-4OCH3 and DRTB-4OH) get redshifted, but these get blue shifted for the electron-accepting derivatives (DRTB-4F and DRTB-4Cl) in comparison with those of DRTB-T. These changes in the electronic and optical properties of the modified structures result in higher PCE in BHJ OSCs with the blended active layer of DRTB-4F: NITI, DRTB-4Cl: NITI, in comparison with that of OSC with the active layer of DRTB-T: NITI and the highest being 15.0 in DRTB-4Cl: NITI. Our results may be expected to provide valuable insights into design optimization, leading to the fabrication of more efficient OSCs.


  • Open Access

    An Estimation of the Anthropogenic Heat Emissions in Darwin City Using Urban Microclimate Simulations

    by Shehani Rajapaksha, Raphael Chukwuka Nnachi, Muhammad Atiq Ur Rehman Tariq, Anne W. M. Ng, Malik Muneeb Abid, Paras Sidiqui, Muhammad Farooq Rais, Erum Aamir, Luis Herrera Diaz, Saeed Kimiaei, et al.

    The energy consumption due to urbanization and man-made activities has resulted in production of waste, heat, and pollution in the urban environment. These have further resulted in undesirable environmental issues such as the production of excessive Anthropogenic Heat Emissions (AHE), thus leading to an increased Urban Heat Island (UHI) effect. The aim of this study was to estimate the total AHE based on the contribution of three major sources of waste heat generation in an urban environment, i.e., buildings, vehicular traffic, and human metabolism. Furthermore, a comparison of dominating anthropogenic heat factor of Darwin with that of other major international cities was carried out. Field measurements of microclimate (temperatures, humidity, solar radiation, and other factors of climate measures) were conducted along Smith Street, Darwin City. Then, surveys were conducted to collect information regarding the buildings, vehicle traffic and Human population (metabolism) in the study area. Each individual component of AHE was calculated based on a conceptual framework of the anthropogenic heat model developed within this study. The results showed that AHE from buildings is the most dominant factor influencing the total AHE in Darwin, contributing to about 87% to 95% of total AHE. This is followed by vehicular traffic (4–13%) and lastly, human metabolism (0.1–0.8%). The study also shows that Darwin gains an average of 990 Wm−2 solar power on a peak day. This study proves that building anthropogenic heat is the major dominating factor influencing the UHI in tropical urban climates.


  • Open Access

    Reducing the Cooling Loads of Buildings Using Shading Devices: A Case Study in Darwin

    by Aiman Mohammed, Muhammad Atiq Ur Rehman Tariq, Anne Wai Man Ng, Zeeshan Zaheer, Safwan Sadeq, Mahmood Mohammed, Hooman Mehdizadeh-Rad

    It is estimated that almost 40% of the world’s energy is consumed by buildings’ heating, ventilation, and air conditioning systems. This consumption increases by 3% every year and will reach 70% by 2050 due to rapid urbanisation and population growth. In Darwin, building energy consumption is even higher and accounts for up to 55% due to the hot and humid weather conditions. Singapore has the same weather conditions but less energy consumption, with only 38% compared to Darwin. Solar radiation can be defined as electromagnetic radiation emitted by the Sun and the Darwin area receives a large amount of solar radiation; building energy consumption can be reduced hugely if this radiation is blocked effectively by analysing appropriate shading devices. This study investigated the influence of different types of shading devices on the cooling load of a town hall building located in Darwin, Australia, and proposed the optimal shading device. The results showed that the horizontal fins led to a 5% reduction in the cooling load of the building. In contrast, adding a variation to the device angles and length increased the savings to 8%. The results demonstrated that the overhangs were more efficient than the fins, contributing 9.2% energy savings, and the cooling reduction savings were increased to 15.5% with design and length variations.


  • Open Access

    Performance Evaluation of Phase Change Materials to Reduce the Cooling Load of Buildings in a Tropical Climate

    by Punita Sangwan, Hooman Mehdizadeh-Rad, Anne Wai Man Ng, Muhammad Atiq Ur Rehman Tariq, Raphael Chukwuka Nnachi

    Tropical region such as Darwin has similar weather patterns throughout the year, thus creating higher energy demands in residential buildings. Typically, buildings consume about 40 per cent of the total energy consumption for indoor heating and cooling. Therefore, building envelopes are linked with design strategies such as the use of thermal energy storage and phase change materials (PCM) to minimize this energy consumption by storing a large amount of thermal energy. Primarily, PCMs are targeted by researchers for use in different components of buildings for thermal efficiency; thus, this study aimed to provide a suitable PCM to optimize indoor thermal comfort and minimize the cooling loads of residential buildings in tropical climates through simulation of a tropical climate building and provide optimum thickness for the selected material. Microencapsulated PCM mixed with gypsum in wallboards were used to reduce the cooling load of a building located in Darwin. The cooling load of the building was calculated using Revit software. A comparison of the cooling load of the building was carried out using PCM-incorporated wallboards of thicknesses of 0 cm, 1 cm and 2 cm in Energy Plus software. The total cooling load decreased by 1.1% when the 1-centimetre-thickness was applied to the wall, whereas a 1.5% reduction was obtained when a 2-centimetre-thick PCM layer was applied. Furthermore, the reduced cooling loads due to impregnation of the PCM-based gypsum wallboard gave reduced energy consumption. Ultimately, the 2-centimetre-thickness PCM-based gypsum wallboard gave a maximum reduction in cooling load with a 7.6% reduction in total site energy and 4.76% energy saving in USD/m2/year.


  • Open Access

    An Energy Performance Evaluation of Commercially Available Window Glazing in Darwin’s Tropical Climate

    by Hooman Mehdizadeh-Rad, Taimoor Ahmad Choudhry, Anne W. M. Ng, Zohreh Rajabi, Muhammad Farooq Rais, Asad Zia, Muhammad Atiq Ur Rehman Tariq

    A total of 40% of the world’s energy produced is utilized to maintain thermal comfort for the occupants of the building. Governments are taking measures collectively to regulate energy efficient buildings to reduce carbon emissions globally. Windows account for more than half of total energy losses in the buildings. The employment of energy efficient glazing in the construction industry is not common in Australia. This paper investigates several types of commercially available windows and their effectiveness in the hot and humid climate of Darwin. Although extensive literature is available for cold regions, these windows have not been studied in hot and humid climates such as the climate in Darwin. Building cooling loads of an academic building were calculated using Autodesk Revit Architecture and Carrier HAP. Double glazed variants offered approximately a 5% reduction in cooling loads and had a payback period of nearly 7 to 9 years, depending on the type of gas used to fill the pane cavity. The results indicate that triple glazed, or aerogel-based windows will provide about 11–12 % of energy saving in cooling loads. These can be a viable alternative and have a payback period of 11 years, while their average service life expectancy is 30 years. It was found that the feasibility of efficient glazing depends on market price, building usage, and energy efficiency of an overall building envelope.


  • Open Access

    Sources of Thermal Power Generation and Their Influence on the Operating Temperature of Organic Solar Cells

    by Hooman Mehdizadeh-Rad, Kiran Sreedhar Ram, Farhad Mehdizadeh-Rad, David Ompong, Daniel Dodzi Yao Setsoafia, Naveen Kumar Elumalai, Furong Zhu, Jai Singh

    Thermal stability, closely associated with the operating temperature, is one of the desired properties for practical applications of organic solar cells (OSCs). In this paper, an OSC of the structure of ITO/PEDOT:PSS/P3HT:PCBM/ZnO/Ag was fabricated, and its current-voltage (J-V) characteristics and operating temperature were measured. The operating temperature of the same OSC was simulated using an analytical model, taking into consideration the heat transfer, charge carrier drift-diffusion and different thermal generation processes. The simulated results agreed well with the experimental ones. It was found that the thermalization of charge carriers above the band gap had the highest influence on the operating temperature of the OSCs. The energy off-set at the donor/acceptor interface in the bulk heterojunction (BHJ) was shown to have a negligible impact on the thermal stability of the OSCs. However, the energy off-sets at the electrode/charge-transporting layer and BHJ/charge-transporting layer interfaces had greater impacts on the operating temperature of OSCs at the short circuit current and maximum power point conditions. Our results revealed that a variation over the energy off-set range from 0.1 to 0.9 eV would induce an almost 10-time increase in the corresponding thermal power generation, e.g., from 0.001 to 0.01 W, in the cells operated at the short circuit current condition, contributing to about 16.7% of the total solar power absorbed in the OSC.