AUAi Ueno

Ai Ueno

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Ai Ueno has a total of 30 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Nanolayer‐Encapsulated Stretchable Liquid‐Metal Sheets for Thermal Management

    by Daisuke Kuse, Yudai Kaneko, Ryohei Fujita, Tatsuhiro Horii, Daishi Shiojiri, Yuta Ozawa, Kyohei Nagatake, Tamami Takano, Yutaka Isoda, Aoi Koishikawa, et al.

    Efficient thermal management in stretchable electronics demands materials that seamlessly integrate high thermal conductivity, mechanical flexibility, and reliable interface stability. This paper presents a stretchable, thermally conductive, biphasic, liquid‐metal sheet (LM sheet)—formed by dispersing copper particles in gallium‐based liquid metal—encapsulated between nanoscale styrene–butadiene–styrene elastomer layers. This trilayer architecture establishes continuous thermal‐conduction pathways while providing excellent electrical insulation and corrosion resistance. The LM sheet achieves impressive in‐plane and through‐plane thermal conductivities (40.4 and 16.7 W m −1  K −1 , respectively), with an elongation at break >200%. Notably, it retains 96% of its thermal conductivity even under 100% tensile strain. It adheres strongly to various substrates without adhesives, excellently spreading heat in flexible heaters and stretchable LED devices under both static and stretched conditions. This paper presents a compelling strategy for developing next‐generation thermal‐interface materials for deformable and skin‐integrated electronic systems.


  • Open Access

    Design and Fabrication of a Micropillar-Pumped Polymer Loop Heat Pipe

    by Masaaki Hashimoto, Taiga Kawakami, Abdulkareem Alasli, Ryobu Nomura, Hosei Nagano, Ai Ueno

    This letter presents a micropillar-pumped polymer loop heat pipe (LHP) with potential applications in flexible electronics. A unique evaporator with a micro pillar wick was designed for a flexible polymer LHP. The polymer LHP was fabricated via simple and cost-effective soft lithography, omitting the need for a porous wick. This design and fabrication approach facilitated passive two-phase cooling in the polymer LHP, with up to 34 $^{\circ}$ C reduction in evaporator temperature when compared to a non-fluid-charged state in a horizontal orientation. 2023-0140


  • Visual Observation and Analytical Study of the Heat Load Sharing Mode in Multi-Evaporator Loop Heat Pipe

    by Masafumi Kizawa, Noriyuki Watanabe, Ai Ueno, Xinyu Chang, Hosei Nagano

    In this paper, the operating characteristics of the heat load sharing mode of multiple-evaporator loop heat pipe (MLHP) were elucidated based on a visual observation test. The heat load sharing mode is a function of MLHPs that can share the heat between the evaporators through the vapor without electronic power for the heat storage utilization. A visualized MLHP with two evaporators and one condenser was designed and fabricated. To simulate the heat load sharing mode in the MLHP, one evaporator was heated in the range of 40–280 W and the other evaporator was cooled using a water jacket in the range of 10–80 °C. Under the heat load sharing mode, the flow behaviors in the evaporator cores and the compensation chambers were visually observed using borescope cameras, respectively. Moreover, two operating modes (defined as Mode A and Mode B) that affect the maximum heat sharing capability were identified. In Mode A, the heat sharing rate was proportional to the heat dissipation at the cooled side of evaporator, where the capillary force at the wick significantly affected the operation mode. By contrast, in Mode B, the heat sharing rate reached the upper limit and then was constant regardless of the heat dissipation. Furthermore, the proposed concept model can predict the transition of the operation mode from Mode A to Mode B.


  • Open Access

    Measurement of Line Distribution of Thermal Contact Resistance Using Microscopic Lock-In Thermography

    by Takuya Ishizaki, Ai Ueno, Hosei Nagano

    This paper proposes a new thermal contact resistance measurement method using lock-in thermography. Using the lock-in thermography with an infrared microscope, the local temperature behavior in the frequency domain across the contact interface was visualized in microscale. Additionally, a new thermal contact resistance measurement principle was constructed considering the superimposition of the reflected and transmitted temperature wave at the boundary and taking into account the intensity distribution of the heating laser as the gaussian distribution, and the specific geometrical condition of the laminated plate sample. As a result of the experiments, the one-dimensional distribution of the thermal contact resistance was obtained along the contact interface from the analysis of the phase lag.


  • Experimental Investigation on a Thin-Loop Heat Pipe With New Evaporator Structure

    by A. Ueno, S. Tomita, H. Nagano

    This paper presents thin-loop heat pipes (tLHPs) with evaporator thickness of 1 mm and a one-way transport length of 200 mm. Grooves and liquid cores are mounted on the evaporator case in the design of a flat evaporator. Liquid cores play a critical role in reducing the pressure drop in the wick and in increasing the path length for heat transfer. A one-dimensional steady model was applied to the design of the tLHP. New tLHPs with thin evaporator (26 × 24 × t1 mm3) were fabricated by a three-dimensional printer. First, two kinds of tLHP systems were (type-1) fabricated with different wick materials—microglass paper (MGP) and Shirasu porous glass (SPG). Ethanol was selected as a working fluid. The experimental results showed the both LHPs can transport heat up to 12 W. Second, the evaporator structure was modified based on the experimental results with the type-1 tLHP, and the tLHP with SPG wick (type-2) was fabricated. The experimental results demonstrated the stable operation. The operation temperature was 83 °C, and the thermal resistance became 1.98 °C/W. The power cycle test at the range of a heat load from 5 to 10 W was also conducted. No temperature hysteresis was observed during three cycles.


  • Open Access

    Dynamic Thermal Contact Resistance Measurement Method Using Lock-in Thermography

    by Takuya Ishizaki, Taichi Igami, Ai Ueno, Hosei Nagano

    This paper proposes a new thermal contact resistance measurement method using lock-in thermography. By the lock-in thermography with an infrared microscope, the dynamic temperature behavior across the contact interface was visualized in the sample side surface. Meanwhile, a new thermal contact resistance measurement principle was constructed by the superimposition of the temperature wave from virtual heat sources in consideration of the thermal contact resistance at the interface. Consequently, the thermal contact resistance was obtained as a fitting parameter by fitting the theoretical curve to the measured amplitude and phase lag. The validity of the principle was shown.