Bo Ma
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Bo Ma has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Chao Wang
College of Smart Materials and Future Energy, Fudan University, Shanghai, China
6 shared publications Churui Li
College of Smart Materials and Future Energy, Fudan University, Shanghai, China
6 shared publications- Rui Jin
College of Smart Materials and Future Energy, Fudan University, Shanghai, China
5 shared publications Bo Jia
Fundamental Science on Optical Fiber Security Research Center, Fudan University, Shanghai, China
3 shared publications- Chenyue He
College of Smart Materials and Future Energy, Fudan University, Shanghai, China
3 shared publications Yang Yan
Department of Materials Science, Fudan University, Shanghai, China
3 shared publications
Latest Publications
- 10 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 38 (16) , 1173-1176
Interference Module Noise Suppression Model for Interferometric Distributed Optical Fiber Sensing
Interferometric distributed optical fiber vibration sensing (iDOFVS) system is critically important in optical fiber sensing. The stability of interference module environment significantly impacts system noise performance. In this paper, an interference-module time-delay fiber (TDF) noise suppression model is proposed for iDOFVS on the basis of an auxiliary reference interferometer, which addresses persistent localization failure under TDF-induced noise. Through theoretical analysis, the transmission principle of the interference-module TDF-induced noise is clarified and validated. Vibration signal localization experiments are conducted over a 50 km urban optical fiber line. Experimental results show that the proposed technique reduces the overall localization error from 61.3 m to 18.9 m and increases the average signal-to-noise ratio from 20.25 dB to 26.81 dB. The proposed technique improves localization accuracy while reducing the size of the equipment, offering practical value for distributed vibration sensing applications.
- 10 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 38 (16) , 1173-1176
Interference Module Noise Suppression Model for Interferometric Distributed Optical Fiber Sensing
Interferometric distributed optical fiber vibration sensing (iDOFVS) system is critically important in optical fiber sensing. The stability of interference module environment significantly impacts system noise performance. In this paper, an interference-module time-delay fiber (TDF) noise suppression model is proposed for iDOFVS on the basis of an auxiliary reference interferometer, which addresses persistent localization failure under TDF-induced noise. Through theoretical analysis, the transmission principle of the interference-module TDF-induced noise is clarified and validated. Vibration signal localization experiments are conducted over a 50 km urban optical fiber line. Experimental results show that the proposed technique reduces the overall localization error from 61.3 m to 18.9 m and increases the average signal-to-noise ratio from 20.25 dB to 26.81 dB. The proposed technique improves localization accuracy while reducing the size of the equipment, offering practical value for distributed vibration sensing applications.
- 1 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 43 (5) , 2394-2400
Study on XPM Phenomena in Single-Core Sensing System Integrated With OTDR and MZ-Sagnac Interferometer
- 1 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 43 (5) , 2394-2400
Study on XPM Phenomena in Single-Core Sensing System Integrated With OTDR and MZ-Sagnac Interferometer
- 27 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 37 (1) , 45-48
Position Characteristics Removing Algorithm for Pattern Recognition in Interferometric DOFS
In distributed optical fiber sensing system, pattern recognition is employed to identify vibration signals. This letter introduces a novel algorithm for removing position characteristics to enhance the pattern recognition accuracy based on single core feedback interference system. The detrimental effects of position characteristics on signal identification are analyzed and simulated. Experiments using a hybrid Mach-Zehnder and Sagnac interferometer combined with a convolutional neural network show a classification accuracy of 98.1% across seven types of position-independent vibration signals. This represents a 1.1% improvement over original signals. Focused on accurately classifying vibration signals from various locations, the position characteristics removing algorithm allows classifier trained solely on data collected from a single point, with enhanced accuracy and the ability to generalize across different signal types and locations.
- 27 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 37 (1) , 45-48
Position Characteristics Removing Algorithm for Pattern Recognition in Interferometric DOFS
In distributed optical fiber sensing system, pattern recognition is employed to identify vibration signals. This letter introduces a novel algorithm for removing position characteristics to enhance the pattern recognition accuracy based on single core feedback interference system. The detrimental effects of position characteristics on signal identification are analyzed and simulated. Experiments using a hybrid Mach-Zehnder and Sagnac interferometer combined with a convolutional neural network show a classification accuracy of 98.1% across seven types of position-independent vibration signals. This represents a 1.1% improvement over original signals. Focused on accurately classifying vibration signals from various locations, the position characteristics removing algorithm allows classifier trained solely on data collected from a single point, with enhanced accuracy and the ability to generalize across different signal types and locations.
- 25 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 43 (5) , 2438-2448
Positioning Error Limits and Noise Analysis in Hybrid MZ-Sagnac Interferometric Distributed Optical Fiber Sensing System
In hybrid MZ-Sagnac interferometric distributed optical fiber sensing system, positioning accuracy is crucial for practical engineering applications. Beyond identifying disturbance locations, quantifying positioning error is essential to evaluate the reliability of the results, which is critical for real-world engineering. In this paper, the factors influencing positioning error is analyzed, and a comprehensive assessment of the system accuracy is provided. The Cramer-Rao lower bound and correlator performance estimate methods are employed to evaluate positioning accuracy. The analysis reveals that positioning error is influenced by the signal-to-noise ratio (SNR) and signal bandwidth, and system noise is served as a key limiting factor. Various noise sources are analyzed, and strategies for noise mitigation are discussed. A theoretical derivation of noise propagation is conducted, leading to the determination of the minimum detectable phase. The experimental setup involves measuring system noise and evaluating positioning performance by placing the optical fiber in a soundproof room and introducing external disturbances at various positions along the fiber. Results show that the system phase noise level is measured at approximately 10 -5 rad at 1 kHz. With a sensing fiber length of 70 km and an SNR of 30 dB, the positioning error for signals with varying bandwidths is demonstrated to be less than 10 m.
- 25 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 43 (5) , 2438-2448
Positioning Error Limits and Noise Analysis in Hybrid MZ-Sagnac Interferometric Distributed Optical Fiber Sensing System
In hybrid MZ-Sagnac interferometric distributed optical fiber sensing system, positioning accuracy is crucial for practical engineering applications. Beyond identifying disturbance locations, quantifying positioning error is essential to evaluate the reliability of the results, which is critical for real-world engineering. In this paper, the factors influencing positioning error is analyzed, and a comprehensive assessment of the system accuracy is provided. The Cramer-Rao lower bound and correlator performance estimate methods are employed to evaluate positioning accuracy. The analysis reveals that positioning error is influenced by the signal-to-noise ratio (SNR) and signal bandwidth, and system noise is served as a key limiting factor. Various noise sources are analyzed, and strategies for noise mitigation are discussed. A theoretical derivation of noise propagation is conducted, leading to the determination of the minimum detectable phase. The experimental setup involves measuring system noise and evaluating positioning performance by placing the optical fiber in a soundproof room and introducing external disturbances at various positions along the fiber. Results show that the system phase noise level is measured at approximately 10 -5 rad at 1 kHz. With a sensing fiber length of 70 km and an SNR of 30 dB, the positioning error for signals with varying bandwidths is demonstrated to be less than 10 m.
- 12 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 24 (8) , 12426-12432
Improved Vibration Localization Algorithm for Multiple Intrusions Based on Phase Spectrum Estimation in Distributed Mach–Zender/Sagnac Optical Fiber Sensing System
Interferometric distributed optical fiber sensing technology has emerged as an important branch in the field of optical fiber sensors, and the research on the technology is of great significance. In this paper, a distributed optical fiber vibration sensing localization algorithm based on phase spectrum time delay estimation is proposed. The algorithm effectively overcomes the limitations in stationary periodic vibration signals localization and multiple vibration signals localization. Theoretical analysis is presented to clarify the principle of vibration localization, especially for multiple vibrations localization. Experimental verification of vibration signal localization on a 40 km optical fiber is demonstrated. The experimental results show that the localization error is less than 20 m for the single-point stationary periodic vibration signals, while less than 50 m for the instantaneous vibration signals. This algorithm achieves the simultaneous localization of multiple stationary periodic vibration signals, while also enabling the concurrent localization of both stationary periodic signals and instantaneous signals. The algorithm shows the capability of multiple vibration signals localization.
- 12 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 24 (8) , 12426-12432
Improved Vibration Localization Algorithm for Multiple Intrusions Based on Phase Spectrum Estimation in Distributed Mach–Zender/Sagnac Optical Fiber Sensing System
Interferometric distributed optical fiber sensing technology has emerged as an important branch in the field of optical fiber sensors, and the research on the technology is of great significance. In this paper, a distributed optical fiber vibration sensing localization algorithm based on phase spectrum time delay estimation is proposed. The algorithm effectively overcomes the limitations in stationary periodic vibration signals localization and multiple vibration signals localization. Theoretical analysis is presented to clarify the principle of vibration localization, especially for multiple vibrations localization. Experimental verification of vibration signal localization on a 40 km optical fiber is demonstrated. The experimental results show that the localization error is less than 20 m for the single-point stationary periodic vibration signals, while less than 50 m for the instantaneous vibration signals. This algorithm achieves the simultaneous localization of multiple stationary periodic vibration signals, while also enabling the concurrent localization of both stationary periodic signals and instantaneous signals. The algorithm shows the capability of multiple vibration signals localization.
- 24 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 23 (19) , 23069-23078
Two-Dimensional Timestamp-Based Sliding Window Cross Correlation Localization Algorithm for Distributed Optical Fiber Vibration Sensing Interferometer
Distributed optical fiber sensing interferometers have emerged as promising tools for various sensing applications. In this paper, we present a novel 2-dimension timestamp-based sliding window cross-correlation algorithm for a distributed optical fiber sensing interferometer based on shifting difference signal reconstruction. The proposed scheme overcomes the limitation of traditional cross-correlation in the multiple vibration situations, enabling to distinguishing multiple disturbance signals. Theoretical analysis on quantization noise and performance with different window lengths is presented. The experimental demonstration over a 60 km fiber is conducted to localize vibration signals. By incorporation fitting, the proposed algorithm achieves the spatial resolution improvement from ±20 m to ±2 m with an average localization accuracy of ±4.34 m at the sensing length of 60 km (±0.014%). The proposed algorithm significantly improves the accuracy of localization and enables real-time tracking of cross-correlation patterns in both spatial and time domains, thereby improving localization accuracy and versatility of signal monitoring.
- 24 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 23 (19) , 23069-23078
Two-Dimensional Timestamp-Based Sliding Window Cross Correlation Localization Algorithm for Distributed Optical Fiber Vibration Sensing Interferometer
Distributed optical fiber sensing interferometers have emerged as promising tools for various sensing applications. In this paper, we present a novel 2-dimension timestamp-based sliding window cross-correlation algorithm for a distributed optical fiber sensing interferometer based on shifting difference signal reconstruction. The proposed scheme overcomes the limitation of traditional cross-correlation in the multiple vibration situations, enabling to distinguishing multiple disturbance signals. Theoretical analysis on quantization noise and performance with different window lengths is presented. The experimental demonstration over a 60 km fiber is conducted to localize vibration signals. By incorporation fitting, the proposed algorithm achieves the spatial resolution improvement from ±20 m to ±2 m with an average localization accuracy of ±4.34 m at the sensing length of 60 km (±0.014%). The proposed algorithm significantly improves the accuracy of localization and enables real-time tracking of cross-correlation patterns in both spatial and time domains, thereby improving localization accuracy and versatility of signal monitoring.
- 1 October 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 186-190
On-line Crack Monitoring Technology of Steam Cooler Girth Welding Based on the Acoustic Emission Principle
Micro-cracks can easily form in the girth welding zone of a steam cooler. The presence of these cracks in the alternating load will produce fatigue growth and cause equipment failure. Acousitc emission on-line monitoring of the girth weld is proposed to ensure the healthy and stable operation of the steam cooler. Attenuation testing of the acoustic emission waveguide and acoustic emission characteristic testing of weld crack propagation are methods created to mitigate acoustic emission signal attenuation problems in on-line monitoring technology. Acoustic emission on-line monitoring is used to collect and process the attenuation of acoustic emission signals under varying waveguides. Results illustrate that accurate design of the waveguide rod structure can effectively reduce acoustic emission signal attenuation. To verify the feasibility of acoustic emission on-line monitoring technology, the acoustic emission characteristics of fatigue crack propagation in weld cracks were investigated using the acoustic emission on-line monitoring method. A large number of acoustic emission signals were collected during the fatigue propagation of weld cracks using this technique. This finding verifies the suitability of on-line acoustic emission monitoring technology for on-line monitoring of cracks in the girth weld of a steam cooler.
- 1 October 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 186-190
On-line Crack Monitoring Technology of Steam Cooler Girth Welding Based on the Acoustic Emission Principle
Micro-cracks can easily form in the girth welding zone of a steam cooler. The presence of these cracks in the alternating load will produce fatigue growth and cause equipment failure. Acousitc emission on-line monitoring of the girth weld is proposed to ensure the healthy and stable operation of the steam cooler. Attenuation testing of the acoustic emission waveguide and acoustic emission characteristic testing of weld crack propagation are methods created to mitigate acoustic emission signal attenuation problems in on-line monitoring technology. Acoustic emission on-line monitoring is used to collect and process the attenuation of acoustic emission signals under varying waveguides. Results illustrate that accurate design of the waveguide rod structure can effectively reduce acoustic emission signal attenuation. To verify the feasibility of acoustic emission on-line monitoring technology, the acoustic emission characteristics of fatigue crack propagation in weld cracks were investigated using the acoustic emission on-line monitoring method. A large number of acoustic emission signals were collected during the fatigue propagation of weld cracks using this technique. This finding verifies the suitability of on-line acoustic emission monitoring technology for on-line monitoring of cracks in the girth weld of a steam cooler.