HPHanisha Ponnuru

Hanisha Ponnuru

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Hanisha Ponnuru has a total of 30 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Interfacial stress transfer of MXene/Natural rubber nanocomposites

    by Ishara Wijesinghe, Ashley Locke, Rebecca A. Fieth, Hiran Chathuranga, Yashodha Kondarage, Pouya Rajaee, Hanisha Ponnuru, Chathushka D. Hettige Dharmasiri, Ruixiang Bai, Zhenkun Lei, et al.

  • Open Access

    Synergistic enhancement of mechanical and thermal properties of natural rubber composites via interface engineering using MXene hybrid fillers

    by Ishara Wijesinghe, Ashley Locke, Rebecca A Fieth, Hiran Chathuranga, Chathushka D. Hettige Dharmasiri, Yashodha Kondarage, Pouya Rajaee, Hanisha Ponnuru, Sajani Wimalachandra, Ruixiang Bai, et al.


  • Open Access

    Synergistic Enhancement of Mechanical and Thermal Properties of Natural Rubber Composites via Interface Engineering using MXene Hybrid Fillers

    by Ishara Wijesinghe, Ashley Locke, Rebecca Fieth, Hiran Chathuranga, Chathushka D. Hettige Dharmasiri, Yashodha Kondarage, Pouya Rajaee, Hanisha Ponnuru, Sajani Wimalachandra, Ruixiang Bai, et al.

    MXene’s superior mechanical properties make it a promising two-dimensional inorganic filler for natural rubber. However, its hydrophilicity causes weak filler-rubber interactions, poor dispersion, and inadequate reinforcement efficiency. Existing surface modifications, such as hydrogen bonding, often suffer from interfacial failures and filler aggregation. In this study, we develop a novel interface engineering approach via in situ loading of zinc oxide onto MXene, followed by grafting (3-mercaptopropyl) trimethoxysilane to create a hybrid filler for natural rubber. Excellent filler dispersion and strong bonding are achieved by silane-mediated covalent crosslinking of MXene with natural rubber via a thiol-ene reaction. The increased crosslink density is attributed to the reduction in activation energy caused by the introduction of zinc oxide. The reinforced rubber has increased tensile strength, toughness, creep resistance, and thermal stability. In addition, the composite has also demonstrated excellent wet skid and low rolling resistance. Overall, this work provides a new interface engineering approach to tailor the properties of natural rubber by incorporating MXene hybrid fillers.

  • Open Access

    Surface Modification of Single‐Crystalline Ni‐Rich Cathode Materials with Gallium Oxide for High‐Voltage Electrochemical Cycling

    by Hanisha Ponnuru, Abhishek Kulkarni, Joade Lennox, Sen Wang, Ishara Wijesinghe, Shuhang Wu, Rebecca Fieth, Nunzio Motta, Anthony P. O’mUllane, Cheng Yan

    Elongated lithium diffusion lengths, parasitic interfacial reactions, and rapid capacity fading continue to hinder the practical application of single‐crystalline Ni‐rich Li[Ni x Co y Mn 1− x − y ]O 2 (SC NCM) cathodes. Although existing surface modification strategies enhance electrochemical stability, high charge transfer resistance and low lithium diffusion result in poor cycling performance. In this work, a lithiophilic Ga 2 O 3 surface‐coated SC NCM material with 83% Ni content is synthesized for the first time via a wet chemical and postannealing route. The Ga 2 O 3 ‐coated material delivers 149.54 mAh g −1 with 57.33% retention after 300 cycles at 1 C over a potential window of 3.0–4.5 V. Compared to the uncoated counterpart, the modified material exhibits a 37.50% reduction in charge transfer resistance and a 79.20% increment in lithium diffusion. Moreover, the nonfaradaic electrochemical active surface area shows only a 1.1% reduction after extended cycling, suggesting effective interfacial stabilization and possible mitigation of HF‐induced surface degradation. These findings demonstrate that the surface modification of NCM materials with lithiophilic Ga‐based oxides is an effective strategy to enhance Li transport, suppress interfacial side reactions, which results in much improved electrochemical performance for next‐generation lithium‐ion batteries.

  • Unveiling the Correlation Between Structural Stability and Electrochemical Characteristics of Single Crystalline Layered Ni‐Rich Cathodes

    by Hanisha Ponnuru, Sagar Dhananjay Jadhav, Michael W. M. Jones, Konstantin L. Faershteyn, Benedicta Arhatari, Ishara Wijesinghe, Sen Wang, Anthony P. O’ Mullane, Cheng Yan

    Single crystalline (SC) Ni‐rich layered lithium metal oxides are promising cathode materials for lithium‐ion batteries due to their high theoretical capacity (> 200 mAh g −1 ) and reduced cobalt composition. However, electrochemical behavior of Ni‐rich materials is underexplored and requires a better understanding to address existing challenges such as elongated Li‐ion diffusion pathways and unstable cycling performance. In this study, SC cathode materials with 83% and 90% Ni content are electrochemically cycled at 1 C from 3 to 4.5 V for up to 300 charge/discharge cycles to investigate changes in impedance, non‐faradaic and faradaic electrochemical active surface areas, and structural evolution. Non‐faradaic electrochemical active surface area (ECSA) measurement increases from 1.81 to 3.30 m 2 g −1 for smaller particles sized NCM 90 (3.12 µm) and 3.14 to 3.52 m 2 g −1 for larger particles sized NCM 83 (6.18 µm) after 300 cycles. Faradaic ECSA for NCM 83 increased by 34.4% at the reduction stage, whereas NCM 90 reduced by 61.46% contributing to recurring surface reconstruction and microcracking. Micro‐computed tomography reveals greater material loss in NCM 83 (≈4.5%) compared to NCM 90 (≈2%), attributed to larger particle size. These insights shed new light on surface and structural changes in SC high‐Ni cathodes and their effects on electrochemical performance.


  • Open Access

    The role of dopants in mitigating the chemo‐mechanical degradation of Ni‐rich cathode: A critical review

    by Imesha Rambukwella, Hanisha Ponnuru, Cheng Yan

    Ni‐rich cathodes are more promising candidates to the increasing demand for high capacity and the ability to operate at high voltages. However, the high Ni content creates a trade‐off between energy density and cycling stability, mainly caused by the chemo‐mechanical degradation. Oxygen evolution, cation mixing, rock salt formation, phase transition, and crack formation contribute to the degradation process. To overcome this problem, strategies such as doping, surface coating, and core‐shell structures have been employed. The advantage of doping is to engineer the cathode surface, structure, and particle morphology simultaneously. This review aims to summarize recent advances in understanding chemo‐mechanical degradation mechanism and the role of different dopants in enhancing the thermal stability and overall electrochemical performance. The pinning and pillaring effects of dopants on suppressing oxygen evolution, cation mixing, and phase transition are introduced. It is found that the higher ionic radii enable dopants to reside on cathode particles, preserving the particle surface and refining particle morphology to suppress crack formation. Finally, the effect of doping on Li ion diffusion, rate capability, and long‐term stability are discussed.


  • Recent Advances in Liquid Metals for Rechargeable Batteries

    by Hanisha Ponnuru, Ifra Marriam, Imesha Rambukwella, Jun‐Chao Zheng, Cheng Yan

    Liquid metals (LMs) with their unique properties are considered for a range of applications such as energy storage, catalysis, electronics, and biomedical engineering. Recently, the introduction of LMs into rechargeable batteries has not only proven to improve overall performance but also overcome commonly known challenges like low energy density, material degradation, interface failure, and poor system integrity. Specifically, room‐temperature LMs such as gallium (Ga), Ga‐based alloys (GBAs), and metallic mercury (Hg) are promising candidates in rechargeable batteries due to their low viscosity, high electrical and thermal conductivity, excellent deformability, superior electrochemical properties, and self‐healing capability. Herein, a review of recent advances in LMs for rechargeable batteries, starting with a brief introduction to LMs fundamentals and their properties is presented. Then, an extensive literature review is carried out to summarize the LMs’ advances in addressing existing challenges of lithium‐ion, lithium‐metal, lithium–sulfur, and other rechargeable batteries. The current state of the art and future perspective are also put forward. It is believed that highlighting potential developments pertaining to LMs can fascinate researchers in exploring them for future rechargeable batteries.