JDJonas L. S. Dickmanns

Jonas L. S. Dickmanns

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Jonas L. S. Dickmanns has a total of 39 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Correlating Formation Conditions to Graphite Resistance, Rate Capability, Cycling Stability, and Gassing in FEC-Containing Li-Ion Batteries

    by Michael Geserer, Jonas L. S. Dickmanns, Louis Hartmann, Filippo Maglia, Roland Jung, Lennart Reuter

    The beneficial effect of fluoroethylene carbonate (FEC) as a co-solvent and electrolyte additive on the cycle life of lithium-ion batteries, particularly those employing high-voltage cathode active materials, has been demonstrated in numerous studies. To further elucidate the effect of varying FEC content, as well as the impact of formation temperature on the properties of the graphite SEI, we performed formation between 10 °C and 60 °C with cells containing either 2 wt% or 20 wt% FEC in LP-57. The irreversible capacity loss due to SEI formation and the arising intercalation resistance (representing the sum of charge-transfer and SEI resistance), determined by means of electrochemical impedance spectroscopy, increased with higher temperature and FEC content. The impact of both quantities on the full-cell performance was assessed in coin and T-cells, revealing enhanced cycling stability for cells that were formed at elevated temperatures, despite a higher susceptibility to lithium plating accompanied by a decreased rate capability for their T-cell analogues when evaluating the rate performance. Employing on-line electrochemical mass spectrometry (OEMS), we further show that higher temperatures and higher FEC contents give rise to a more pronounced, but also more condensed, gas evolution during the initial cycles.

  • Open Access

    Comparative Analysis of Silicon-Carbon Composite, Graphite, and Microscale Silicon Anodes for Next-Gen Lithium-Ion Batteries

    by Jonas L. S. Dickmanns, Moritz Bock, Johanna Poschenrieder, Stefan Haufe, Hubert A. Gasteiger

    While silicon can significantly enhance the energy density of lithium-ion battery (LiB) anodes, its volume expansion of +280% in the fully lithiated Li 15 Si 4 state and the resulting poor cycle life have limited its use in commercial applications. This study investigates a novel silicon-carbon (Si/C) composite anode material, composed of a carbon host structure infiltrated by silicon. The Si/C performance characteristics is compared with those of state-of-the-art graphite (Gra) and silicon-dominant (Si) anodes in full-cells with an NCA cathode. Full-cell charge and discharge rate tests show the same rate capability for the Si/C and Si anodes, which outperform the Gra anode. For a capacity retention of 80%, the cycle life of the full-cells with the Si/C anode of ∼650 cycles far exceeds the ∼200 cycles obtained with the Si anode but is still short of the ∼1000 cycles obtained with the graphite anode. The projected stack-level gravimetric/volumetric energy densities assuming commercial separator and current collector properties are ∼7%/∼16% higher for the Si/C compared to the graphite anode, approaching the ∼15%/∼20% energy density gains of the Si anodes. Consequently, this Si/C composite is a promising anode active material for LiBs, offering a combination of high energy density, rate capability, and lifetime.


  • Open Access

    Changes in Structure and Ionic Resistance of Lithium-Ion Battery Graphite Electrodes – Part II: Impact of State-of-Charge

    by Lennart Reuter, Jonas L. S. Dickmanns, Robert Morasch, Sven Friedrich, Andreas Jossen, Hubert A. Gasteiger

    The crystalline volume change of graphite upon lithiation and delithiation is reported to lead to a change in the thickness and porosity of porous electrodes. Using electrochemical impedance spectroscopy, this study resolved the concomitant state-of-charge (SOC) dependent change of the ionic pore resistance (R_Ion ) of graphite electrodes via measurements conducted at low temperatures and stack pressures of 0.2 and 1.0 MPa. The pressure-dependent results reveal an increase of R_Ion upon complete lithiation of up to ~32% and ~45% at the lower and higher pressure, respectively. This data was combined with literature data on the volumetric expansion of graphite particles obtained from X-ray diffraction measurements to reveal a significant decrease in porosity upon lithiation. From there, the thickness changes of the graphite electrodes can be calculated. Inferable from this is a significant SOC-dependent variation in the MacMullin number (>30%), a crucial simulation parameter, of up to +40%. We observe a net pore volume decrease upon lithiation, particularly for a higher stack pressure. The reduction in the pore volume of up to 15% induces an electrolyte pumping effect. The study transfers these insights obtained from laboratory-type cells to commercial cells and addresses the recently described effect of electrolyte motion-induced salt inhomogeneity (EMSI).


  • Open Access

    Changes in Structure and Ionic Resistance of Lithium-Ion Battery Graphite Electrodes – Part I: Impact of Formation and SEI

    by Jonas L. S. Dickmanns, Lennart Reuter, Robert Morasch, Filippo Maglia, Roland Jung, Hubert A. Gasteiger

    With the interest in achieving higher gravimetric and volumetric energy densities in lithium-ion batteries, increasing the electrode loading and reducing its thickness—and consequently porosity—while maintaining low tortuosity is desirable. Achieving high power density requires a thorough understanding of these structural parameters of thick graphite electrodes and their changes during the formation of the solid-electrolyte-interphase (SEI). Graphite electrodes with loadings of ∼ 10 mg cm − 2 and pristine porosities ranging from 20–50% underwent formation at 45 °C in LP57 + 2% VC electrolyte. The ionic pore resistance after formation was quantified in non-blocking conditions using a μ-reference electrode and measuring electrochemical impedance spectroscopy at −5 °C. Upon formation, the ionic resistance of the graphite electrodes increased by up to 25%, which was quantitatively related to specific changes in electrode thickness, porosity, and tortuosity. The change in electrode thickness depended on the pristine porosity and increased by up to ∼11%. Mercury intrusion porosimetry revealed a decrease in porosity for initially high-porosity electrodes and an increase for those with low pristine porosity. The tortuosity of the electrodes increased by up to ∼10% upon formation. The thickness and density of the SEI were determined using a combination of pycnometry and mass-gain measurements, yielding 16–20 nm and ∼ 1.07 g cm − 3 , respectively.


  • Amorphization Progress of Microscale-Silicon Studied via Operando and in Situ X-Ray Diffraction during Formation and Cycling

    by Jonas L. S. Dickmanns, Lukas Grossmann, Moritz Bock, Marc Holst, Thien An Pham, Ralph Gilles, Hubert Andreas Gasteiger

    Silicon as an anode active material for lithium-ion batteries has a theoretical gravimetric capacity of 3579 mAh g-1, considering the highest electrochemically lithiated phase of Li3.75Si.1 Hence, silicon has gained increasing interest in the last years to either partially or completely replace graphite in commercial lithium-ion batteries to increase energy density.2 However, the expansion of silicon of up to 300% upon complete lithiation bears challenges such as particle cracking, loss of electrical contact to the active material, and the continuous formation of the solid-electrolyte interphase (SEI). To decrease these detrimental effects, partial lithiation of microscale silicon was introduced, limiting the used capacity of silicon to ~1200 mAh g-1 and thus reducing its overall expansion, rendering ~250 cycles in full-cells possible.3 XRD measurements during the initial lithiation of crystalline silicon revealed that it is irreversibly amorphized in the first cycle when its potential drops below ~170 mV vs. Li+/Li.4 In the case of partial lithiation of microscale silicon, cycling above this potential limit leads to amorphized silicon particles with a remaining crystalline fraction. In this state, the amorphized part forms a lower lithiated phase LixSi (with x~2), which can be reversibly de-/lithiated.5 In this study, the amorphization progress of microscale silicon full-cells using a single-layer pouch cell setupwas investigated operando over the first four formation cycles and in situ after extended cycling. The anodes consisted of 70% silicon (d 50 =4.5 µm, Wacker Chemie AG), 8% LiPAA binder (Sigma Aldrich), 2% conductive carbon (Super C65, Imerys), and 8% graphite (KS6L, Imerys). The cathode consisted of a nickel-rich transition metal oxide cathode active material (LiNi0.83Co0.12Mn0.05O2, BASF SE). As electrolyte, a 1 M LiPF6 in FEC:DEC 2:8 (v:v) was used. As shown in Figure 1, the cycling performance in pouch cells, reaching 80% state-of-health (SOH) after ~250 cycles at 25 °C matches well with the literature.6 Figure 1 highlights the cycles at or after which XRD measurements were performed. To accomplish operando XRD measurements, a custom-made pouch cell holder with glassy carbon windows was used, which allows for an operating compression of 2 bar. In this setup, an XRD pattern could be taken every ~15 min for the first four cycles at 0.1 h-1. Using the XRD analysis method developed previously,5 the XRD data confirm a significant amorphization in the first charge, while no amorphization occurs during the relaxation phase and during discharge of the cell. In the second charge, the amorphization continues only after ~70% of the capacity was transferred. The start of amorphization aligns with the anode onset potential of ~170 mV vs. Li+/Li, in accordance with the literature.4,5 With increasing cycling number, the progress of amorphization per cycle decreases. Although only ~33% of the silicon capacity (i.e., 1200 mAh/g) is reversibly used, the amorphization reaches ~70% after 50 cycles, highlighting the significant particle usage. Continuous cycling up to 500 cycles leads to no significant further amorphization of the silicon. References: M. N. Obrovac and L. Christensen, Electrochem. Solid-State Lett., 7, A93–A96 (2004). S. Chae, S. H. Choi, N. Kim, J. Sung, and J. Cho, Angew. Chemie - Int. Ed., 59, 110–135 (2020). D. Jantke, R. Bernhard, E. Hanelt, T. Buhrmester, J. Pfeiffer, and S. Haufe, J. Electrochem. Soc., 166, A3881–A3885 (2019). M. N. Obrovac and L. J. Krause, J. Electrochem. Soc., 154, A103–A108 (2007). M. Graf, C. Berg, R. Bernhard, S. Haufe, J. Pfeiffer, and H. A. Gasteiger, J. Electrochem. Soc., 169 (2022). S. Haufe, R. Bernhard, and J. Pfeiffer, J. Electrochem. Soc., 168, 080531 (2021). Acknowledgements: The authors acknowledge funding from the German Federal Ministry of Economic Affairs and Climate Action through the project CAESAR (grant number 03EI3046F). We thank BASF SE for the NCM cathode material and Wacker Chemie AG for the silicon anode material. The authors thank the Physics Laboratory of the MLZ for measuring time at the diffractometer as well as B. Veltel and A. Book for the adjustment of the instrument. Figure 1


  • Open Access

    Effect of Mechanical Pressure on Rate Capability, Lifetime, and Expansion in Multilayer Pouch Cells with Silicon-Dominant Anodes

    by Sven Friedrich, Simon Helmer, Lennart Reuter, Jonas L. S. Dickmanns, Axel Durdel, Andreas Jossen

    Microscale silicon particles have a higher specific capacity but larger volume expansion than graphite particles, leading to particle decoupling and lifetime limitations. This study investigates a wide range of external mechanical pressures from zero (ZP - 0.00 MPa) to high (HP - 0.50 MPa) pressure to determine the optimal pressure for high rate capability, cyclic lifetime, energy density, low temperature rise, and low cell thickness gain. The cells are characterized by rate tests and impedance spectroscopy, and are aged until 70% state of health (SoH). The post-mortem analysis after 70% SoH and thickness measurements over 360 cycles in a compression test bench offer insights into the thickness gain. Electrochemical results reveal an immediate reduction in discharge capacity upon transitioning from normal pressure (NP - 0.20 MPa) to ZP, with NP and HP exhibiting superior performance over aging. The impedance was reduced initially and over aging for higher mechanical pressures, especially the cathode contact resistance, resulting in lower temperature rises during the rate tests. Overall, applying higher pressures reduced the anode and cell thickness gain. Moreover, the porosity decreased with increasing pressure, as determined by mercury intrusion porosimetry and pycnometer measurements. The increase of the anode mass correlates to the total charge throughput, which is pressure-dependent and the highest for NP.


  • The Effects of Temperature and Fluoroethylene Carbonate Concentration on the Formation of the Graphite SEI and Its Impact on the Full-Cell Performance

    by Michael Geserer, Lennart Reuter, Jonas L. S. Dickmanns, Louis Hartmann, Filippo Maglia, Roland Jung, Hubert Andreas Gasteiger

    Extending the cycle-life of state-of-the-art lithium-ion batteries (LiBs) is, amongst other aspects, predicated on optimizing the properties of the solid electrolyte interphase (SEI), such as its stability and resistance.[1] It is formed at the negative electrode during the first cycles by electrolyte decomposition and acts as a passivating layer between the electrode surface and the electrolyte.[2,3] Since the SEI formation is accompanied by an irreversible loss of cyclable lithium, its stability during cycling is crucial for improving the charge/discharge efficiency of LiBs. Furthermore, the arising resistance associated with the SEI formation, predominantly depending on the SEI thickness, its chemical composition, and its lithium-ion conductivity, all impact the rate performance of the anode.[4] Two of the most crucial factors impacting SEI formation are temperature and electrolyte composition (i.e., using electrolyte additives).[5] Additives are added to the electrolyte to inhibit the predominant reduction of other electrolyte constituents and thereby form an SEI with improved stability during cycling.[1,6,7] One of the most prominent additives for LiBs is fluoroethylene carbonate (FEC), which is preferentially reduced compared to common carbonate solvents (e.g., ethylene carbonate, ethyl methyl carbonate) due to its higher reduction potential.[7] In this study, we investigated the influence of the formation temperature between 10 and 60 °C, as well as the concentration of FEC (2 and 20 %wt in EC:EMC 3:7 wt/wt with 1 M LiPF6, Gotion, USA) on the characteristics of a synthetic graphite (SMG-A5, Resonac, Japan) anode, both in SMG/Li half-cells and in Ni-rich NCM/SMG full cells. We quantified the first-cycle irreversible capacity loss (ICL) in SMG/Li half cells with a lithium reference electrode after two 0.1 C formation cycles and compared the FEC containing electrolytes to the baseline- (LP-57) and an LP-572 (1 M LiPF6 in EC:EMC 3:7 wt/wt + 2 %wt vinylene carbonate (VC), Gotion, USA) electrolyte. Employing electrochemical impedance spectroscopy in an SMG/Li half-cell setup with a µ-reference electrode and a free-standing graphite electrode,[8,9] we could further quantify the intercalation resistance (R Int, representing the sum of the charge-transfer and the SEI resistance) after an identical formation protocol at 40 % SOC. Both quantities, the ICL and R Int, increase with increasing formation temperature and higher FEC content. The impact of an increasing R Int on the rate performance was tested in Ni-rich NCM/SMG full cells with a lithium reference electrode, revealing a decreased rate capability and higher susceptibility for lithium plating for cells that were formed at higher temperatures and contained 20 %wt FEC. Additionally, the cycling stability of Ni-rich NCM/SMG full cells at 25 °C was assessed in coin cells. Despite an increased ICL and R Int after formation, cells that were formed at elevated temperatures and contained 20 %wt FEC showed enhanced cycling stability compared to those that were formed at a lower temperature and contained less FEC. Finally, on-line electrochemical mass spectrometry (OEMS) was employed to quantify the evolved gases during the formation of a Ni-rich NCM/SMG full cell containing either of the FEC-containing electrolytes at different temperatures. In accordance with an increased ICL and R Int, a higher formation temperature, as well as a higher FEC content, gave rise to a more pronounced gas evolution during formation. References: [1] D. Y. Wang, N. N. Sinha, J. C. Burns, C. P. Aiken, R. Petibon, J. R. Dahn, J. Electrochem. Soc. 2014, 161, A467–A472. [2] E. Peled, J. Electrochem. Soc. 1979, 126, 2047–2051. [3] E. Peled, S. Menkin, J. Electrochem. Soc. 2017, 164, 1703–1719. [4] S. Solchenbach, X. Huang, D. Pritzl, J. Landesfeind, H. A. Gasteiger, J. Electrochem. Soc. 2021, 168, 110503. [5] J. Asenbauer, T. Eisenmann, M. Kuenzel, A. Kazzazi, Z. Chen, D. Bresser, Sustain. Energy Fuels 2020, 4, 5387–5416. [6] T. Taskovic, L. Thompson, A. Eldesoky, M. Lumsden, J. R. Dahn, J. Electrochem. Soc. 2021, 168, 010514. [7] K. U. Schwenke, S. Solchenbach, J. Demeaux, B. L. Lucht, H. A. Gasteiger, J. Electrochem. Soc. 2019, 166, A2035–A2047. [8] S. Solchenbach, D. Pritzl, E. J. Y. Kong, J. Landesfeind, H. A. Gasteiger, J. Electrochem. Soc. 2016, 163, A2265–A2272. [9] R. Morasch, B. Suthar, H. A. Gasteiger, J. Electrochem. Soc. 2020, 167, 100540. Acknowledgements: This work is financially supported by BMW AG. The authors thank BMW AG for their financial support.

  • Effect of Mechanical Pressure on Rate Capability, Lifetime, and Expansion of Multilayer Pouch Cells with Silicon-Dominant Anodes

    by Sven Friedrich, Simon Helmer, Lennart Reuter, Jonas L. S. Dickmanns, Axel Durdel, Andreas Jossen

    Silicon-dominant (Si) anodes with microscale silicon particles meet the requirements of high energy density and low costs due to its ten times higher theoretical electrochemical capacity of 3579 mAh/gSi (Li15Si4) compared to graphite,1 lifetime extension due to partial lithiation,1-2 and high abundance and economic availability due to existing industrial infrastructure.1-2 The major drawback of silicon is the large volume expansion of nearly 300% upon full lithiation. This hinders the broad application of silicon as an active anode material due to continuous SEI (re-) formation and electrochemical milling of particles. Additionally, the volume expansion impacts the overall electrode stability, leading to thickness changes, the disruption of the electronic pathways, and the decoupling of particles. Although the approach of partial lithiation of microscale1 Si eases these effects by lowering the overall volume expansion, these problems still exist.2,3 In this work, the effect of different mechanical cell pressures on lithium-ion batteries with partially lithiated silicon-dominant anodes is investigated with 5.4 Ah multilayer pouch cells as a follow-up study of our previous work with laboratory T-Cells.3 Methodologically, a novel cell holder and pressure device were developed and validated to apply different mechanical cell pressures. Our investigation covers a pressure range from uncompressed as zero (ZP, 0.00 MPa) to high (HP, 0.50 MPa) external cell pressure to determine the optimal pressure for high rate capacity, cyclic lifetime, energy density, and low thickness gain. The cells were tested by checkup cycles at C/10, rate tests up to 3C, and cycled at C/2 until 70% state of health (SoH). Electrochemical impedance spectroscopy was conducted at different SoHs to quantify the effect of mechanical pressures on the impedance response.4 The post-mortem analysis after reaching 70% SoH and operando thickness measurements in a compression test5 bench give insights into the electrode and cell thickness gain. In the electrochemical results, the discharge capacity Q DCH was immediately reduced by decreasing the mechanical pressure from 0.20 MPa to 0.00 MPa or 0.05 MPa, both for the cells in the cell holder (see inset in Figure 1a) and the compression test bench (not shown). This pressure change was also quantified by an increased charge-averaged full cell potential during charging and a decreased charge-averaged full cell potential during discharging. The impedance was reduced for higher mechanical pressure, especially the cathode contact resistance initially and over aging, resulting in lower temperature increases during the rate tests. The capacity retention Q DCH and the total charge throughput were increased to 360 cycles until 70% SoH for higher mechanical pressures at NP (normal pressure, 0.20 MPa) and HP (see Figure 1) compared to 181 cycles for ZP. Overall, applying higher mechanical pressures reduced the thickness increase, as shown by operando thickness measurements and the post-mortem analysis. A dependency of the reversible thickness on the charged capacity was found. Moreover, the porosity decreased with increasing pressure, which was measured with mercury intrusion porosimetry (MIP) and pycnometry. The anode mass increase correlates to the total charge throughput, which is pressure-dependent and the highest for NP. Our findings demonstrate that applying the optimal mechanical cell pressure is significant when using microscale silicon-dominant anodes. We recommend a mechanical pressure of 0.50 MPa for increased rate capacity, minimizing impedance, heat evolution, and thickness gain, and 0.20 MPa for increased energy density. Acknowledgments: S.F. gratefully acknowledges the financial support from the BMBF (Federal Ministry of Education and Research, Germany) under the auspices of the ExZellTUM III project (grant number 03XP0255). The authors want to thank the research battery production team of iwb at TUM for the multi-layer pouch cell production. We also thank Wacker Chemie for kindly providing the microscale silicon material. References: [1] Jantke et al. Silicon-Dominant Anodes Based on Microscale Silicon Particles under Partial Lithiation with High Capacity and Cycle Stability. Journal of The Electrochemical Society 2019, 166, A3881–A3885. [2] Haufe, S.; Bernhard, R.; Pfeiffer, J. Revealing the Failure Mechanism of Partially Lithiated Silicon-Dominant Anodes Based on Microscale Silicon Particles. Journal of The Electrochemical Society 2021, 168, 080531. [3] Friedrich et al. Effect of Mechanical Pressure on Lifetime, Expansion, and Porosity of Silicon Dominant Anodes in Laboratory Lithium-Ion Cells. ECS Meeting Abstract A04-0538. [4] Helmer et al. Deconvolution of an Soc-Dependent Contact Resistance in a Multilayer Pouch Cell Using Impedance Spectroscopy ECS Meeting Abstracts MA2023-01(2):618-618. [5] Aufschläger et al. High precision measurement of reversible swelling and electrochemical performance of flexibly compressed 5 Ah NMC622/graphite lithium-ion pouch cells. Journal of Energy Storage 2023, 59, 106483. Figure 1

  • Formation and Cycling of Microscale Silicon Anodes at Elevated Temperatures with FEC-Based and EC-Based Electrolytes

    by Jonas L. S. Dickmanns, Lennart Reuter, Hubert Andreas Gasteiger

    Silicon is a promising candidate to replace graphite (372 mAh g-1) as anode material in lithium-ion batteries (LIBs) due to its high theoretical gravimetric capacity of 3589 mAh g-1.1 Graphite is already partially substituted by silicon in commercial battery applications in order to increase the energy density of LIBs.2 However, a complete transition to silicon is still hindered by the extreme volume expansion of up to 300% upon complete electrochemical lithiation to Li15Si4.3 This causes particle cracking, electrical contact loss of active material, and the continuous (re-)formation of the solid electrolyte interphase (SEI) on the newly formed surface, leading to a continuous loss of cyclable lithium and a fast capacity fading of the cell. One approach to mitigate Si particle cracking is the partial lithiation of microscale silicon, limiting the capacity to ~1200 mAh g-1, i.e., one-third of the theoretical capacity, enabling a cycle-life of more than 200 cycles before reaching 80% state-of-health (SOH).4 While electronic disconnection of lithiated silicon contributes to the overall cyclable lithium losses, the continuous formation of the SEI remains one of the major challenges that limit the lifetime.5 Fluoroethylene carbonate (FEC) has been shown to be one of the most suitable additives for silicon-containing cells to ensure the formation of a suitable SEI and comparably stable cycling performance.6,7 However, especially at elevated temperatures, FEC decomposes to form vinylene carbonate and hydrogen fluoride, which is detrimental to the SEI.8 This study investigated temperature-dependent cycle-life stability of microscale-silicon dominant anodes with EC-based and FEC-based electrolytes at room and elevated temperature. The electrodes consist of 70% silicon (Wacker Chemie AG) with an LiPAA binder (8%) and conductive carbon (2%). Additionally, graphite (8% KS6L, Imerys) was added to enhance the electronic conductivity, whereby within the operating voltage range of the anode, only a minor capacity of the graphite is used. As electrolytes, either 1 M LiPF6 in EC:DEC 1:2 v:v (EC-based) or 1 M LiPF6 in FEC:DEC 2:8 v:v (FEC-based) were used. Full-cells were cycled with a nickel-rich transition metal oxide cathode active material (LiNi0.83Co0.12Mn0.05O2 (NCM831205), BASF SE) based cathode at 25 °C and 45 °C. As shown in Figure 1, cycling in coin cells revealed the expected decreased cycle-life of cells with the FEC-based electrolyte at 45 °C (light blue) compared to 25 °C (dark blue).8 However, cycling cells with the FEC-free, EC-based electrolyte (green) at elevated temperatures, showed the opposite trend. The cycle-life until 80% SOH increased by 110 cycles (+100%), surpassing that of the cells with the FEC-based electrolyte at 45 °C. The charge-averaged mean voltages for both charge and discharge were investigated to identify the main failure mechanisms. This allowed us to differentiate between the loss of cyclable lithium and internal cell resistance build-up. To better understand the contributions of anode and cathode to capacity fading, we assembled Swagelok® T-Cells with the same cell chemistry and cycled them analogously. While the resistance of the cathode remained nearly constant over the whole course of cycling, the resistance of the anode showed an increase with decreasing cell capacity. Furthermore, online electrochemical mass spectrometry (OEMS) was performed to determine the gases evolved during formation with the EC-based electrolyte at 25 °C and 45 °C. This allowed us to gain insights into the overall SEI formation mechanism and to differentiate the formation of suitable SEI components. References: M. N. Obrovac and L. Christensen, Electrochem. Solid-State Lett., 7, A93–A96 (2004). S. Chae, S. H. Choi, N. Kim, J. Sung, and J. Cho, Angew. Chemie - Int. Ed., 59, 110–135 (2020). M. N. Obrovac and V. L. Chevrier, Chem. Rev., 114, 11444–11502 (2014). D. Jantke, R. Bernhard, E. Hanelt, T. Buhrmester, J. Pfeiffer, and S. Haufe, J. Electrochem. Soc., 166, A3881–A3885 (2019). S. Haufe, R. Bernhard, and J. Pfeiffer, J. Electrochem. Soc., 168, 080531 (2021). V. Etacheri, O. Haik, Y. Goffer, G. A. Roberts, I. C. Stefan, R. Fasching, and D. Aurbach, Langmuir, 28, 965–976 (2012). R. Jung, M. Metzger, D. Haering, S. Solchenbach, C. Marino, N. Tsiouvaras, C. Stinner, and H. A. Gasteiger, J. Electrochem. Soc., 163, A1705–A1716 (2016). T. Teufl, D. J. Pritzl, L. Hartmann, S. Solchenbach, M. Mendez, and H. Gasteiger, J. Electrochem. Soc. (2023). Acknowledgements: The authors gratefully acknowledge funding from the German Federal Ministry of Economic Affairs and Climate Action through the project CAESAR (grant number 03EI3046F). We would like to thank BASF SE for providing the NCM cathode material. Also, we kindly thank Wacker Chemie AG for providing the silicon anode material. Figure 1


  • Elucidating the Effect of Pre-Lithiation of Silicon Dominant Anodes on the Full Cell Performance

    by Moritz Bock, Jonas L. S. Dickmanns, Hubert Andreas Gasteiger

    Over the last few years, there has been a high interest in increasing the energy density of lithium-ion batteries in order to increase the driving range of battery electric vehicles. On a material level, silicon is a promising anode active material candidate due to its high theoretical capacity of 3579 mAh g-1, which is approximately ten-fold higher than that of the currently used graphite anodes with a theoretical capacity of 372 mAh g-1.[1] However, the main drawbacks of silicon are its intrinsic volume expansion of +300 % upon lithiation.[2] This leads to rupturing of the passivating solid electrolyte interphase (SEI), particle cracking, and loss of electronic contact, limiting the lifetime of batteries with silicon based anodes, thus hindering their transition into application. As a possible solution, Jantke et al. proposed the concept of partial utilization of µm-sized crystalline silicon, where only one-third of the theoretical capacity is used for (de)lithiation. Thereby, a crystalline core remains, and the volume expansion on the particle-level is reduced to approximately + 100%.[3] In addition, it was shown that irreversible losses during the formation and upon cycling can be compensated by pre-lithiation of the anode, which increases the lifetime significantly.[4,5] In this study, we investigated a promising cell chemistry for high-energy applications, containing a Si-dominant anode and a cathode based on a Co-free lithium- and manganese-rich NMC. The here used anode consists of 70 wt% silicon, 20 wt% graphite, 2 wt% conductive C65, and 8 wt% LiPAA-binder. Note that graphite mainly acts as a conductive additive within the operating voltage window, with a negligible contribution to the overall anode capacity. The electrochemical testing was conducted at 25 °C in Swagelok® T-cells containing two glass fiber separators, a 1M LiPF6 in FEC:DEC (2:8, v:v) electrolyte and a lithium metal reference. Without pre-lithiation, these full-cells suffered from rapid capacity fading, reaching the 80 % state-of-health (SOH) criterion after ~100 cycles. As will be discussed, our analysis shows that the primary mode of failure in these cells is the loss of cyclable lithium, evidenced by an increase in the end-of-discharge potential at the anode. It was found that with increasing end-of-discharge potential at the anode, the anode resistance at low state-of-charge rises significantly. Therefore, silicon anodes were lithiated in coin half-cells to 25, 50, and 75 % of the reversible cathode capacity (corresponding to 300, 600, and 900 mAh gSi -1). Then, the anodes were harvested in the lithiated state and assembled in a Swagelok® T-cell with the same cathode, separator, and electrolyte as the non-pre-lithiated reference cells. Pre-lithiation leads to similar reversible charge/discharge capacities, but generates a cyclable lithium reservoir in the anode. Successively increasing the pre-lithiation of the anode increases the lifetime from 100 to 550 cycles. The onset of the above-described aging phenomena is delayed by 150 cycles for every additional 25 % pre-lithiation. Further, the influence of aging and lithium inventory on anode and cathode resistance will be discussed, showing that the increase in anode resistance is mainly a function of (de)lithiation rather than cycle number. Acknowledgments: The authors gratefully acknowledge the funding from the BMBF (Federal Ministry of Education and Research, Germany) in the ExZellTUM III project (grant number 03XP0255). We also kindly thank Wacker Chemie AG and BASF SE for providing the anode and cathode active materials. References: [1] M. N. Obrovac, L. Christensen, Electrochem. Solid-State Lett. 2004, 7, A93–A96. [2] M. N. Obrovac, V. L. Chevrier, Chem. Rev. 2014, 114, 11444–11502. [3] D. Jantke, R. Bernhard, E. Hanelt, T. Buhrmester, J. Pfeiffer, S. Haufe, J. Electrochem. Soc. 2019, 166, A3881–A3885. [4] S. Haufe, R. Bernhard, J. Pfeiffer, J. Electrochem. Soc. 2021, 168, 080531. [5] V.L. Chevrier, L. Liu, R. Wohl, A. Chandrasoma, J. A. Vega, K. W. Eberman, P. Stegmaier, E. Figgemeier, J. Electrochem. Soc. 2018, 165, A1129–A1136.